XTEMOS ELEMENT
AJAX PRODUCTS TABS
Wooden Pipette Stand, Holds 24 pipettes Vertically
Ice Plant Trainer
The Plant uses ice can system. The cans filled with fresh wafer are kept in a tank in which brine is circulated. The brine is cooled by the refrigerant, which in turn cools the water in can and ice formation takes place.
SPECIFICATIONS:
1.Compressor : Kirioskar make hermetically sealed compressor using R 12 Refrigerant. 2.Condenser : 4 row type air cooled. 3.Expansion Valve : 0.5 TR capacity. 4.Evaporator : 1/2″ O.D. copper tube – 75 feet long. 5.Filter – Drier : Silica gel filled – 3/8″ flare connections. 6.Main Tank : 600 mm X 375 mm 7.Total Ice Cane Capacity : 7 Kg 8.Ice Making Capacity : 7 Kg / 4 Hours. 9.Thermocol insulation : 6.5″ 10.Brine Stirrer : Motor driven fan, 1 phase, 1/10 HP, 1440.INSTRUMENTATION:
1.Temperature Indicator : Digital Type O300°c, with 1 °c least count, using Cr/Al thermocouples. Accuracy 1 % of full reading. 2.Compressor Energy Meter : Single Phase, 10 – 20 Amp. Capacity. 3.Pressure Gauge: a)0-21 Kg/cm2 b) -1 to 10.6 Kg/cm2 c) Both of 65 mm dial. 4.Digital Thermometer CONTROLS : 1.HP/LP Cutout : Auto reset type. 2.Thermostat : Auto reset type. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Floor Area – 2m. X 1.5m. X 1.5m. Height. 2.220 V., 15 Amp.Single Phase Stabilized power supply
IoT Based Real Time Applications
Specification:
• To check the imbalance and deflection of moving machinery used for measuring various mechanical vibration • By using high performance acceleration meter realize the repetitiveness and accurate measurement. • Velocity : 0.01 – 400.0mm/s RMS 0.001-16.00inch/s • Acceleration : 0.1 – 400m/s2 equivalent peak • : 0.3 – 1312ft/s • Displacement : 0.001 – 4.000mm.
Electric Motor St. Louis
Description
The motor consists of a two pole armature mounted between the ends of two bar magnets. The armature has a two section commutator and a pair of slip-rings on its shaft and is so constructed that the wire cannot slip off the iron core. The upper bearing and brushes for the commutator are mounted on a strong upright. Separate brushes are provided for the commutator and for slip rings and each are connected to a terminal. The magnets are held in position by thumb screws.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Polarising Filter Stress Determination
Description
Demonstrate stress patterns in solids with this new and valuable equipment. Two polarising filters, mounted on a graduated frame are placed on a plastic base. Clear acrylic pieces of different shapes are introduced between the filters; when pressure is applied to the solids the resulting stress patterns are observed. An important method of demonstrating polarisation and stress. Includes instructions.
Tubing, Silicon
Plantation Pots
Plantation Pots, moulded in polypropylene, are available in four different sizes.
The Plantation Pots have a downward extended rim, which provide convenient lifting even if the pot is filled.
The bottom of the pot is provided with holes for drain purpose.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Plantation Pots 100 mm | 20 | |
| Plantation Pots 150 mm | 20 | |
| Plantation Pots 200 mm | 20 | |
| Plantation Pots 250 mm | 20 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Digital Kymograph
Digital Kymograph has gained immense recognition in exporting and supplying quality assured array of Digital Kymograph Consists of a revolving drum that is wrapped with a sheet of paper and this kymograph is used to measure atmospheric pressure, the functioning of steam engines and tuning fork vibrations. Offered kymograph is made in complete compliance with predefined industry norms at our well-equipped unit. Furthermore, this Digital Kymograph is extensively appreciated and demanded in the market due to its rugged design and excellent performance.
Features
Excellent performance. Power efficient. Easy operation. Result accuracy.Specification
Digital Speed Selection. Spirit Level: For adjusting level. Auto Stop after One Complete Cycle. 16 x 2 LCD Digital Display with Back Light simultaneous display of all functions on the display and selection through display. Highly Accurate Speed : E/C System Speeds available -0.12.,0.25,0,.50,0.75,1.00,1.25,mm/Sec With Accurance of +/-0.01%. Timer With Alarm Time Multiplier (o-10 min in multiple of 30 sec.) for indicating washing Cycle Drug Injection times etc. Very Low Power Consumption (12 volts 1 Amp.). Operated with Stepper Motor which is highly accurate and run by Microprocessor based program. Battery Back Up (Optional): Auto Conversion to Battery Mode in Case of Electricity Failure. Back up 1 to 4 hours. Special Chrome Plated and Powder Coated Body: Extremely Resistant to Corrosion and Leak Proof Design. Self Lubrication Gear. And More Feature Available.
Photon Energy Array
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Handheld Anemometer Digital
Bucket & Cylinder
For demonstrating Archimedes principle this is a simple form in brass, suitable for class demonstration or individual use.
The bucket has suspension loop at the top and hook at the bottom.
The cylinder has a suspension hook at one end. Size 6 cm long, overall length when extended 16 cm.
A Bucket and Cylinder
B Bucket and Cylinder Large Size
Telescopic Alidade
Conductivity Appratus Ingen – Hauzs
Description
Consists of 5 metal rods of different materials having equal lenghts mounted in sheet metal box 150 x 90 x 100mm with corks. Metal rods 150 x 3 mm length x diameter, one each of aluminium,brass, copper, lead and iron, embedded along one side of a metal tank size 150 x 90 x 100 mm length x width x height.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Impact Of Jet On Vanes Apparatus
DESCRIPTION:-
The Set-up consists of two sided clear fabrication. Water is fed through a nozzle and discharged vertically to strike a target carried on a stem, which extends through the cover. A weight carrier is mounted on the upper end of the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured by adding the weights supplied to the weight pan until the mark on the weight pan corresponds with the level gauge. A total of two targets are provided a flat plat and a hemispherical cup.EXPERIMENTS:-
Ø To measure the force developed by a jet of water impinging upon a different targets (Hemispherical & Flat Plate) and comparison with the forces predicted by the momentum theory.UTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Test Plates : Material Brass (2 Nos.) 1. Flat Plate 2. Hemispherical Cup Ø Nozzle : Material Brass Ø Stainless Steel Chamber : Having of opposite sides made of glass Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 40 Ltrs. Ø Sump Tank : Capacity 60 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Metacentric Height Apparatus
DESCRIPTION:-
A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc. For tilting the ship model, a cross bar with two movable hangers is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus.EXPERIMENTS:-
Ø Determination of the Metacentric height and position of the Metacentric height with angle of heel of ship model.TECHNICAL SPECIFICATION: –
Ø Pontoon : Size 300 x 150 mm (Approx.) with a Horizontal Guide Bar for aliding weight. Ø Material : Stainless Steel Pontoon Ø Water Tank : Size 600 x 400 x 400 mm (Approx.) Ø Front Window of Tank : made of Glass/Perspex Ø A set of weights is supplied with the apparatus. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Pilot Static Tube Set Up
DESCRIPTION:-
A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper / SS is supplied and is fixed below Vernier scale. The Vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow. A U-tube manometer is provided to determine the velocity head. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot tube Ø To plot velocity profile across the cross section of pipeUTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pitot Tube : Material Copper/SS of compatible size fitted with Vernier Scale Ø Test Section : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 40 Ltrs. Ø Sump Tank : Capacity 70 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Displacement Vessel, Glass
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Gas Tap, Regular
Description
Made of brass with superior black powder coating. Regular construction having lever handle with locking arrangement to ensure lever rotation does not go beyond 90°. Output nozzle having 4mm bore. Inlet 3/8 X 26. Flange diameter 50mm with two holes to fix on bench or any other surface with screws. Provided with adapter (6/8, 3.8mm bore) and corresponding nut (8mm bore). Designed to operate at pressure up to 2 psi (0. 14kg/cm2). Suitable for use with coal gas, natural gas and L.P.G.Particulars
Gas Tap, One Way Gas Tap, Two Way Gas Tap, Three Way Gas Tap, Four Way
Fisher Clamp
We bring to you, Fisher Clamp.
The Fisher Clamps are moulded in Polypropylene making it completely corrosion-proof.
The spring-loaded jack in the middle provides a vice like grip to the Burette and prevents it from slipping.
Two tapered wedges are provided to ensure firm grip on rods having diameter ½" or 3/8".
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Fisher Clamp- Single | 12 | |
| Fisher Clamp- Double | 6 |
