XTEMOS ELEMENT
AJAX PRODUCTS TABS
IoT Based Real Time Applications
Specification:
• To check the imbalance and deflection of moving machinery used for measuring various mechanical vibration • By using high performance acceleration meter realize the repetitiveness and accurate measurement. • Velocity : 0.01 – 400.0mm/s RMS 0.001-16.00inch/s • Acceleration : 0.1 – 400m/s2 equivalent peak • : 0.3 – 1312ft/s • Displacement : 0.001 – 4.000mm.
TI MSP430 Development Board
ON Chip Features
• CPU - MSP430F1611 • Core - 16 bit RISC Architecture. • Speed - Up to 8 MHZ. • Flash - 48 KB + 256B. • SRAM (on-chip) - 10KB. • 48 GPIO Lines. Two UARTs. • One I2C Module. One SPI Module. • Two 16 bit Timers. • Five Power Saving Mode. • 12 bit ADC with single channel. • 12 bit DAC with two channel.ON Board Features
• Eight Digital Output - LED Interface. • Two Digital Input. • 16 x 2 Character LCD Interface. • 7 Segment Display via I2C Interface. • 10 Base T Ethernet Connectivity. • SD Card Interface Support. • Audio Interface. • Jtag connector is provided for Debugger. • USB to serial interface provided.
Coriollis Component Of Acceleration
This set up is designed to study coriollis component of Acceleration of a slider crank Mechanism. The apparatus uses hydraulic analogy to represent the rotating slider. It consists of a rotating block with two arms in opposite direction. These tubes can be rotated at various speeds by using a swinging field motor, which also acts as a dynamometer to measure torque applied to rotating tubes. A Perspex window on top cover helps to visualize the process. Rotameter is used to measure water flow rate through tubes. Water is circulated by small monoblaock pump.
Specifications:
1.Main Tank with fiberglass lining. 2.Rotating Arms 9/6 mm dia, 300 mm long. 3.Motor – Swinging field, D.C., 0.5 HP. 4.Rotameter 5.Monoblock Pump 6.Control Panel comprising of – (i) Speed Control Unit. (ii) Speed Indicator. (iii) Necessary switches. 7.Rigid support frame.Range of Experiment:
Coriollis Component of Acceleration can be determined at various speeds of rotation and water flow rates.Service Required:
1.A.C. Single Phase .230 V. stabilized supply. 2.Floor Space -1.5 m X 1.5 m.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Redundant Joint Apparatus
Apparatus consists of three suspension members (spring balances) of different stiffness, which are jointed at a point to form the redundant joint. The upper end of the suspension members being tied in a position to a vertical wooden board. Arrangement is provided to apply a vertical load at the joint and to measure its horizontal and vertical displacement on a paper and also elongations and forces in the suspension members by the help of dial gauges. Dial gauges with magnetic base are provided with the apparatus.
EXPERIMENT:
Comparison of experimental and theoretical results of forces in the members and the component displacement of the loaded joint D of a three bar suspension system for vertical loads.REQUIRED ACCESSORIES:
• Redundant Joint Apparatus • Dial Gauge : 1 No. • Magnetic Base : 1 No. • Hangers : 1 Nos. • Weight of 500gm : As Per requirement.
Cooling System Of An Automobile
In this model the working of a cooling system of a car is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a cooling system of a car are shown in actual working form. This model helps the student to understand the working of the cooling system of a car very easily. It is specially made dissectible for demonstration purposes.
Specific Gravity Specimen Cylinders with Hooks
Tube Sedimentator
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
U Shaped Magnet
Leopold Maneuvers Simulator
Description
One piece fetal baby with palpable fontanelles, spine, shoulders, elbows, and knees Fetal baby may be placed in normal, breech, or transverse position Fetal baby cradled between two “cushions” Cushions may be inflated independently of the other; inflation of the lower cushion raises the fetus to desired position; inflation of the upper cushion creates a firm abdomen as in the ninth month of pregnancy The Palpation Module is designed to be used with the Advanced Childbirth Simulator.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Ray Optics Kit
Description
Consists of 2 lamps and two stands, 1 pair housing shields, 2 combined single and triple slit plates, 2 multiple slit combs, 2 holders for combs and slit plates, 4 wooden light barriers, and following cylindrical lenses, of size 50 x 50 mm. 4 No Lenses of +7D, 2 of +10D, 2 of +17D and 2 of -17D.
Venturimeter Orificemeter Calibration Set Up
DESCRIPTION:-
The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different floe rate. Flow rate of water is measured with the help of measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the Co-efficient of discharged through Venturimeter and Orificemeter Ø To measure discharge through Venturimeter and Orificemeter as flow meters.UTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATIONS: –
Ø Venturimeter : Material Clear Acrylic, Compatible to 1” Dia pipe Ø Orificemeter : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Heat Transfer Activity
Free Force Vortex Apparatus
DESCRIPTION:-
The experimental set up consist of a circular transparent cylindrical tank in which four circumferential jets have been placed along the circumference of the cylinder near its bottom which helps in the formation of free vortex. It is assumed that the torque exerted by these jets is negligible. The Orifice is reducing bush so that a reduced diameter can be investigated. The plate can also be rotated with the help of a variable speed motor so that the cylinder rotates about its vertical Axis with the help of a V belt and forced vortex is formed. Conditions wear allowed to steady state and the depth of flow at any particular point was observed not to change over a period of time. The experimental procedure involves measurement of resulting free surface that represents the variation of the sum of the pressure and datum head.SCOPE OF EXPERIMENTS:-
Ø To plot the surface profile of a free and forced vortex by measurement of the surface profile coordinates and to show that total energy is constant throughout vortex.TECHNICAL SPECIFICATION: –
Ø Cylinder : Material Acrylic Dia. 200mm approx Ø Height of Overflow point : 150mm Ø Drive : FHP variable speed motor, speed way Ø The whole Set-up is well designed and arranged in a good quality painted StructureXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Draining Rack
Draining Rack provides an excellent option for post wash draining of tubes & bottles in the laboratory.
The back plate of this Draining Rack has 20 holes into which pegs are tightened with the help of screw-nuts.
Bottom of the rack is provided with a tray which collects all the waste water drained down which can further be collected in a container via drain tube.
This rack not rot, stain or rust.
Material : Acrylopitrile Butadiene Styrene / Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Draining Rack | 1 |
89C51 Microcontroller Trainer
Specification
• Core :NXP89C51RD2 / 8051 • Internal Memory :64KB Flash, 1KB RAM • External Memory :64KB EPROM, 64KB RAM • 16 Digital Outputs - SMD LED Interface. • 16 Digital Inputs - Switch Interface. • 20X4 Character LCD Interface. • I2C Peripherals : - 8 Bit ADC [8-Bit 4 Channel ADC, Two Potentiometer Provide in on board]. - 8 Bit DAC. • Six 7-Segments Display Interface. • On Board Stepper Motor Driver is provided. • PWM lines are terminated at Terminal Block. • IBM PC Keyboard Interface for entering program. • CPU Lines are terminated at 50 pin Expansion Header.(VBMB and VPIC) • I/O ports terminated to connect to external devices. • Program / Execution switch is provided for serial ISP (Using ISP Utility Software). • ADC, DAC lines are terminated at terminal blocks.
Heart Models
Our capability and industrial know how has enabled us to manufacture, supply and export Heart Models.
Made of superior quality raw materials that are supposed to be the best in the market, these products have a descriptive structure and construction.
With clear depiction of external features and internal structures of the heart, these provide an appropriate indication of various large blood vessels.
These products help in education medical students about the clearer conception of the routes of the systemic and pulmonary circulation in the heart.
Heart Models are packed in special packaging material so as to ensure its safe and secure transit.
Gas Turbines Or Turbojet Engine Model
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
