XTEMOS ELEMENT
AJAX PRODUCTS TABS
Zoology Charts
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tearable and long lasting, with plastic rollers, size 75 x 100 cm. Epithelial tissue, simple & stratified. Connective tissues, loose. Connective tissues skeletal (Bone Cartilage). Connective tissues-Blood. Nerve Cells Types of Nerve Cells Neuroglia Type of muscular tissues Plasmodium Vivax , life cycle Amphioxus Embryological Development Sponge, External morphology with T.S. Hydra, External morphology with T.S. Obelia Life cycle & T.S. in Medus Echinococcus Life Cycle Pinworm Life cycle Earthworm, external structure with T.S. in intestine & internal anatomy Earthworm, circulatory system with reproductive system Snail-L.S. through mouth Snail-reproductive system Crayfish-T.S. in Branchial Chamber Crayfish Reproductive Male & Female Cockroach Mouth parts Cockroach, internal anatomy Starfish, water vascular system Starfish, Digestive system Amphioxus General structure Amphioxus Circulatory system Fish Circulatory system Fish Reproductive system for male & female Frog circulatory system & L.S. in Heart Frog Skeletal system & L.S. in Heart Pigeon skeletal system with fore & hind limbs Pigeon Arterial & Venous system Rabbit Arterial &Venous system with L.S. in heart Rabbit-Reproductive system Male & Female Classification of animals, English only Typical Animal cell, English only
Kaplan Turbine Test Setup
DESCRIPTION:
Kaplan Turbine is an axial flow reaction Turbine named in honor of Dr. B. Kaplan, a Gennan Engineer. This turbine is suitable for low head. The power produced by a turbine is proportional to QH. As the head (H) decreases the J discharge (Q) must increase to produce the same power. The present Set-up consists of a scroll casing housing a runner. Water enters the turbine through the stationary guide vanes and passes through the runner axially. The runner has a hub and airfoil vanes, which are mounted on it. The water is fed to the turbine by means of Centrifugal Pump. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. A transparent hollow cylinder made of acrylic is fitted in between the draught tube and the casing for observation of flow on to the airfoil vanes. This runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of this brake arrangement so that the efficiency of the turbine can be calculated. The Set-up is supplied with control panel. A draught tube is fitted on the Outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and Vacuum Gauge are fitted at the Inlet & Outlet of the turbine to measure the total supply head on the turbine.EXPERIMENT:
1.To study the operation of a Kaplan Turbine 2.To determine the Output Power of Kaplan Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 109 (1.33 HP) | HM 109 (5 HP) | |
| Output Power | 1.33 HP / 1 Kw | 5 HP / 3.75 Kw | |
| Discharge | 1500 LPM (Approx.) | 5000 LPM (Approx.) | |
| Supply Head | 5 m | 5 m | |
| Rope Brake Dynamometer | Dia 200 mm | Dia 300 mm | |
| Sump Tank | Capacity 300 Ltrs. | Capacity 600 Ltrs. | |
| Water Circulation Centrifugal Pump | Capacity 7 HP, Three Phase | Capacity 20 HP, Three Phase | |
| Speed | 1500 RPM (approx.) | ||
| Runner | With adjustable Curved Vanes | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
Angel Property of Cyclic Quadrilateral
Test Tube, with Interchangeable Stopper
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
L Shaped Spreader
We are a prominent Exporter & Trader of L Shaped Spreader.
The L Shaped Spreader is sterile & smooth and enables even spreading of liquid samples across the surface of a jar plate without grouping & cutting the medium.
Avail the L Shaped Spreader from us at nominal market prices.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| L Shaped Spreader | 100 | |
| Micro Pestle (for 0.5 and 1.5 ml MCT) | 12 | |
| Micro Pestle (for 1.5 ml MCT) | 12 |
Resistance Box, Plug Pattern
Description
All plugs are turned to a fine standard taper and are interchangeable. These are moulded in fluted plastic tops. The brass blocks are undercut and are fitted to a thick insulating plate. Heavy 4 mm brass terminals are used. Coils are non-inductively wound and are treated to be strain-free. Coil values are engraved on the plate and an infinity plug is also included. Accuracy ±0.5% for 0.01 to 0.05 ohm coils, ±1% for the rest 0.01 to 0.1 ohm, Total 0.2 ohm 0.1 to 1 ohm, Total 2 ohm 0.1 to 5 ohm, Total 11 ohm 0.1 to 10 ohm, Total 21 ohm 0.1 to 50 ohm, Total 111 ohm 0.1 to 100 ohm, Total 211 ohm 0.1 to 500 ohm, Total 1111 ohm 1 to 10 ohm, Total 20 ohm 1 to 50 ohm, Total 110 ohm 1 to 100 ohm, Total 210 ohm 1 to 500 ohm, Total 1110 ohm 1 to 1000 ohm, Total 2110 ohm 1 to 5000 ohm, Total 11110 ohmXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
FLASK TONG
Rack Pinion Type Steering System
Rack & Pinion Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Water Still with Metal Heater
Specifications
Water stills are carefully designed to produce high purity pyrogen free distilled water. The water still made from 3.3 exp. borosilicate glass comprises of horizontal type boiler, condenser, constant level device, silica sheathed heater, along with stand and clamps.Features
Borosilicate condenser and boiler are with a removable silica sheathed heater and screw threaded connectors for ease of Cleaning. Distillate temperature is approx. between 25° to 45°C which is ensured by an efficient condenser. The stand is powder coated for rust free operation and lustrous appearance. The unit automatically switches off if water level in the boiler falls below heater. Cooling water from the condenser is re-circulated into the boiling chamber, hence saving energy. Drain nozzle/Teflon Stop Cork is provided for easy cleaning and maintenance. Electrical Power: 220/240 V, 50/60Hz, Single Phase Supply.
Comparative Study
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Vertebrate Hearts Vertebrate Brains Vertebrate Skulls Vertebrate Limbs Vertebrate Girdles Vertebrate Urino genital system Vertebrate Embryos Vertebrate Arterial arches circulation Vertebrate Genital apparatus & venous system
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Compound Microscope (Student Microscope)
Specification
Elegant body, practical design and coated lenses. Fixed square stage 120mm x 120 mm with optional mechanical stage or slide clips. Focusing by coarse & fine adjustment knobs. Illumination by plano concave mirror reflector or optional LED light. Eye Piece 10x & 15x Objective 4x, 10x , 40x/45x 100x oil immersion is optional. Available in Styrofoam pack for safe & easy transport. Wooden Box is optional.
Multiple Input/Output Process Trainer
Panel Features
• Power ON/OFF switch • Heater selection switch • Heater and pump indicators • High current fuse carrier for • Heater protection • Provision to run the stirrer • Digital panel meters • Two numbers of industrial PID Controller • Electrical test points are provided to measure the current signal • Mimic DiagramFeatures
• Two numbers of flow Transmitter (DPT) are provided to sense the flow of the liquid. • Three numbers of temperature transmitter (RTD) are provided at various stages to measure the temperature. • Five numbers of level sensor (RF capacitance) are provided to sense the level of each tank. • Industrial type Conductivity sensor is provided to analyze the conductivity of given Solution. • RTD sensor (or) Thermocouple acts as a temperature sensor. • Digital panel meters are provided to indicate the output of each sensor. • Provision to measure the conductivity. • Two numbers of motorized control valve or pneumatic control valve are provided to control the flow of the pipe line. • A powerful thyristor based power driver is provided to drive the heater power. • An industrial type water heater is used as a heat Source. • Storage tank of 50 litre capacity (SS). • Process tank of 15 litre capacity (SS). • Four numbers of acrylic tank are provided to study the response of four tank systems. • In necessary location Ball valve, globe valve and needle valves are provided. • Two numbers of stirrer are provided in the temperature process and alkaline process. • Three numbers of centrifugal pump (FHP) is used to circulate the water from storage tank. • Six numbers of rotameter are provided in the process inlet to visualize the real flow. • Regulated power supply is mounted in the panel. • All the flow lines are fitted by (SS) pipe fitting. • An over head tank is provided to give constant flow. • All the equipments are mounted in a rugged and mobile type metallic work station.
Biological Science Set
Set of 22 slides. Fulfils the requirements of most biology courses.
The slides have been chosen for their relevance to international Curriculum and for the clarity with which they show structures, which may be related directly to function.
The set comprises following slides.
| Adipose tissue | Allium LS root tip for mitosis |
| Allium, Leaf, WM epidermis with stomata | Artery and vein |
| Cucurbita, stem, TS and LS | Entire Kidney, LS Mixed Bacteria |
| Germinating pollen, LS stigma | Human blood smear |
| Ligustrum (Privet) TS leaf | Lung |
| Mixed Pollen | Nerve cells, isolated |
| Nettle stinging cells | Pacinian corpuscle receptor cells |
| Saccharo0myces, budding | Skin |
| Small intestine, TS injected | Squamous, epithelium, cheek cells |
| Stomach, VS | Straited muscle |
| Triticum, LS Seed | Zea Stem, TS and LS |
Block Calorimeter
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Water Still with Metal Heater
Specifications
Water stills are carefully designed to produce high purity pyrogen free distilled water. The water still made from 3.3 exp. borosilicate glass comprises of horizontal type boiler, condenser, constant level device, silica sheathed heater, along with stand and clamps.Features
Borosilicate condenser and boiler are with a removable silica sheathed heater and screw threaded connectors for ease of Cleaning. Distillate temperature is approx. between 25° to 45°C which is ensured by an efficient condenser. The stand is powder coated for rust free operation and lustrous appearance. The unit automatically switches off if water level in the boiler falls below heater. Cooling water from the condenser is re-circulated into the boiling chamber, hence saving energy. Drain nozzle/Teflon Stop Cork is provided for easy cleaning and maintenance. Electrical Power: 220/240 V, 50/60Hz, Single Phase Supply.
Advanced Universal FPGA Trainer
The universal FPGA trainer consist of a main board with many peripheral like USB Device, Ethernet, Serial ports, Parallel Port, VGA port, Graphics LCD, Switches, LED, ADC etc. This motherboard has 4Nos of high speed connectors for plugging the daughter boards, which contains the FPGA of any manufacturers. Separately 2Nos of 100 pin high speed connectors provided for hardware expansion as plug in boards.
• Industry standard interconnection
- 10 MBPS Ethernet
- USB 2.0 Interface
- Two RS232 ports
- 9 pin D connector
• Memory Sub system
- 8 MB x 16 Bit SDRAM
- 4MB x 16 bit flash EEPROM
- 256KB I2C EEPROM
• Additional Features
- One 240 x 128 graphics LCD
- 16 Nos of dip switches
- 16 discrete LEDs
- 4 digit multiplexed 7 segment LED display
- 4 x 4 matrix keyboard
- One VGA Port at 15 pin D connector
- One PS2 connector for keyboard and mouse
- Reset Switch
- I2C Real time Clock
• Analog Input & Output
- 2MSPS SPI ADC (12 Channel)
- Temperature sensor interface
- One 16 bit Stereo CODEC
• 2 Nos. of 100 pin high speed connectors provided to hardware expansion can be used as hardware bus.
• Multilayer board for superior signal integrity.
• 54 I/O pins terminated at 3Nos of 20 pin connector for external interfacing.
Power Steering System
Power Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Pulse Width Modulation and Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Pulse Width Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Built in IC based DC Regulated Power supply ±12 V, +5 V.
2. Four level Built in carrier pulse Output.
3. Frequency Range: 8 KHz, 16 KHz, 32 KHz, 64 KHz Amplitude : 5 Vpp approx.
4. Built in sine wave Audio Frequency Function Generator for modulating signal. Frequency Range: 1 KHz and 2 KHz selectable with a toggle switch Amplitude : 0-10 Vpp and 0-4 Vpp approx.
5. Circuit Diagram for Modulation and Demodulation is printed on the milky white top panel.
Front Suspension System
In this model the working of front suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a front suspension system are shown in actual working form. This model helps the student to understand the working of the front suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Macpherson Type Suspension System
(B) Double Wishbone Type Suspension System
(C) Longitudinal Torsion Bar Type Suspension System
Transistor Char Appt
Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book. It has survived not only five centuries, but also the leap into electronic typesetting, remaining essentially unchanged. It was popularised in the 1960s with the release of Letraset sheets containing Lorem Ipsum passages, and more recently with desktop publishing software like Aldus PageMaker including versions of Lorem Ipsum.
