XTEMOS ELEMENT
AJAX PRODUCTS TABS
Fuel Supply System Petrol MPFI Type
Fuel Supply System Petrol MPFI Type (Actual Working Model) Multi Point Fuel Injection
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under :
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Igniter & Ignition Coil
9. Distributor
10. Spark Plugs
11. Power Supply
12. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of MPFI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
DC Servo Motor Controller
This trainer designed for versatile Applications / Experiments mentioned below. It consists of(i) a PWM Chopper Drive using MOSFET (ii) DC Servo Motor (iii) Speed Sensor (v) PI Loop for speed. This trainer system is a compact & advanced version for class room experiment setup for the students to operate and study a practical speed measurement using optical sensor and speed control system.
FEATURES:
• One 12V PMDC Motor mounted on a open frame. • Speed Range: 0 to 1500 RPM. • Speed Sensor fixed on the frame. - Photo interrupter with optical Encoders. • One F/V converter is provided to convert the pulses to voltage output. • Speed controller provided to select - Proportional circuit. - Proportional plus Integral circuit. • One 3½ digit display to display the speed of the DC Servo motor / set value. • A switch provided to select the reference or the actual speed. • All important signals are terminated at sockets. So that, the student can monitor / measure the signals using CRO, DVM, Frequency counter etc.
Balance
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Jockey
Mechanical Heat Pump Trainer
Heat Pump is a device to pump heat from one source to another. The heat obtained by heat pump is more than that could be obtained by direct electrical heating. The apparatus consists of refrigeration system with water cooled shell and coil type evaporator and condenser.
SPECIFICATIONS:
1.Compressor – Hermetically sealed compressor using R-12 refrigerant, having capacity 0.3 tons of refrigeration. Condensing pressure – max. 15 Kg/cm2 (Actual pressures will depend upon working conditions). 2.Condenser – Shell and coil type with continuous water flow arrangement. 3.Evaporator – Shell and coil type with continuous water flow arrangement. 4.Expansion Valve – Internally equalized thermostatic expansion valve. 5.Measurements – a) Rotameter for condenser & evaporator water flow rate measurement. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for condensing and evaporating pressure – 2 Nos. d) Thermometer for refrigeration cycle & water temp, measurement – 7 e) Wattmeter for compressor input measurement. f) Ammeter for compressor current measurement. 6.Controls – a) HP/LP cutout for compressor. b) Overload protector for compressor. c) Gate valve to control water flow rates. d) Necessary switches and fuse. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 2m, X 2m. X 1.5m. height. 2.220V. 15Amp. Single Phase Stabilized power supply.
Advance Surgical Structure Leg
Description
This model of Advanced Surgical Suturing Leg allows the students to practice cut, suturing, stitches release, enswathing, etc. The elasticity and flexibility of skin can make it for practice hundreds of times. There are some initial wounds on the arm and if all the initial wounds have been sutured, people can cut the arm in other place for new training of suturing.
RF Signal Source with Detector
Specification
• 25 to 6000MHz RF synthesized signal generator. • Programmable attenuator 5, 10, 20, 30dBm up to 1.5GHz. • 40 x 2 LCD Display to display the frequency of the RF signal and RF signal level. • Output level : 0dBm +/2dB upto 1GHz, -5dBm, +/-2dB upto 3GHz, -10dBm, +/-3dB upto 6GHz. • Output impedance : 50 ohm. • One RF Power detector provided for 50 to 1000MHz frequency range and this output is measured • by an ADC and display on the LCD display. • 6 Keys keypad provided to select the desired frequency, attenuation level, Sweep mode. • Step size : 1MHz. • Connectors: - 2 Nos. of 'N' type connector for RF out and RF in. - One "BNC" type connector for RF detector output.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Flow Over Weir Or Open Channel Apparatus
Flow Over Weir Or Open Channel Apparatus:
A ‘WEIR’ is the name given to concrete or masonry structure built across a river (or stream) in order to raise the level of water on the upstream side and to allow the excess water to flow over its entire length to the downstream side. Weirs may also be used for measuring the rate of flow of water in river or streams.
Different shapes of “WEIRS” generally used are sharp-crested weir, broadcasted weir and ogee shaped weir.
In the unit a centrifugal pump sucks the water from the sump tank, and discharges it to a small flow channel. The weir is fitted at the end of channel. All the weirs are interchangeable. The water-flowing over the weir falls in the collector. Water coming at from the collector can be directed to the sump or can be directed in to the measuring tank for measurement of flow.
SPECIFICATIONS:
[1] The unit is provided with following weirs: (a) Sharp-crested weir. (b) Broad-crested weir. (c) Ogee shaped weir. [2] Pump 1/2 H.P. monoblock. [3] Flow measurement – Measuring tank calibrated water flow meter is used. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Floor surface – 2.5 m x 1.5 m. [2] 230 v, 5 amp supply with earthing connection
Demonstration Dynamo
Description
This model uses the same basic assembly as the motor, but is mounted on a baseplate 230 x 90 mm approx. which also carries a hand-drive pulley 120mm. diameter coupled to the smaller dynamo pulley by a rubber belt to give a step-up ration. Electrical output is via a pair of 4mm sockets. The model may also be used as a motor on a 6-8 V D.C. supply.
Stereo Zoom Microscope
Specifications
| Magnification | : | 20x & 40x or 30x and 60x | |
| Eyepiece Lens | : | Wide Field 10x or 15x Paired Eyepiece | |
| Objective | : | 2x and 4x (Turret Type Revolving) | |
| Focusing | : | Vertical movement with rack & pinion, Tension control knob & stroke 50 mm | |
| Inclination | : | 45° | |
| Tube Rotation | : | 360° Rotatable, Removable |
Accessories
Rubber Eye Guard. LED Light Illuminator or Flurescent Ring Illuminator.
Planck’s Constant
Modern LEDs (light emitting diodes) cover the range from deep blue (440 nm) to infra-red (940 nm). By monitoring the voltage at which each LED just begins to emit light a graph of energy input as a function of light emitted frequency can be plotted and an approximate value of Planck’s constant deduced. Complete with viewing tube but without power supply.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Slide Box
We are the major Exporter and Trader of superior quality Slide Boxes .
These Slide Boxes are durable, compact & provide utmost protection to 1" x 3" slides.
Heavy walls will not warp, splinter or crack.
Our Slide Boxes are unaffected by humidity and are thoroughly insect proof.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Slide Box - 25 Slides | 12 | |
| Slide Box - 50 Slides | 12 | |
| Slide Box - 100 Slides | 6 |
Urinary Bladder Model
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Concentric Tube Heat Exchanger
(A)Plain Tube ( Water To Water ):
The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. While the outer tube consists of GI pipe through which cold water flows. The arrangement enables the parallel and counter flow of the cold water. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.
Specifications:
1.Inner copper tube I.D, 12.7mm. and outer G. I. Pipe I. D. 15mm. approx. and 1.5m. length. 2.Thermometers – 4 nos. 3.Measuring flask – 1 Lit. capacity. 4.Geyser-3 kW. Single phase.Services required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x I m x 1 m height. (B) Finned Tube ( Water To Air ): The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. It is finned at its outer diameter to increase the heat transfer surface. While the outer tube consists of GI pipe through which cold air flows. The arrangement enables the parallel and counter flow of the air. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.Specifications:
1.Inner copper tube I.D. 12.7mm. and outer G. I. Pipe I. D. 25mm. approx. and 1m. length. 2.Thermometers – 4 nos. 3.Orifice meter along with manometer. 4.Measuring flask – 1 Lit. Capacity. 5.Geyser-3 kW. Single phase.Services Required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x 1m x 1m height.
PETRI DISH
Product description:
These flat, clear Corning Petri dishes are made from soda lime silica glass and will withstand repeated sterilization (wet or dry). The edges are beaded to provide greater mechanical strength. The covered dish is not airtight. Bottoms also have a triangular enamel reference point for serial dilutions.
Size:
50mm
75mm
100mm
150mm
Air Conditioning Trainer Window Type
Window air conditioner is becoming now a day’s necessity. The unit demonstrates the application of window air conditioner & evaluation of its performance. It consists of a small room to which a small air conditioner is connected the room is provided with a transparent front cover with a heater inside to simulate heat load in the room. Various measurements are provided so that performance of system that is COP of system, actual & theoretical cooling capacity of system & power consumption of unit with different load conditions.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirloskar make, having the capacity of 1/10 ton of refrigeration using R-12 refrigerant to keep room temperature between 20 to 30 c. 2.Condenser – Finned tube type, with forced air flow over the tubes, 3.Capillary tube of matched length as expansion device. 4.Evaporator – Finned tube type with forced air flow, 5.Room – 0.6 X 0.7 X 0.7 m. height, provided with transparent front wall. A heater with input control is provided inside the room. Which simulates different load conditions. 6.Measurements and Controls a) H.P. / L.P. Pressure gauges b) Digital temperature indicator to measure the temperatures at various points. c) Energy meters to measure input to compressor & heater. d) High and low pressure cutout. e) Thermostat to put off the compressor at set room temperature. f) Necessary switch for electrical components.SERVICES REQUIRED:
1.Floor area of 2m X 1 m. 2.230V, 15AC stabilized supply with earthing connection
Fuel Supply System Of A 4 Cylinder Diesel Engine
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Separating Throttling Calorimeter
AIM
To find out dryness fraction of steam by combined separating and throttling calorimeter.
PRODUCT DETAILS
The steam passing out from separating calorimeter may still contain some water vapour , in it . in other words it may not be absolutely dry . again , in a throttling calorimeter steam after passing through the throttle valve must be superheated or at least dry saturated . this limits the extent of dryness fraction that can be reliably measured , depend up on the pressure of steam in the main steam pipe . if a sample of steam, which may be still wet after passing through the throttle valve i.e it will not be superheated . thus under this condition the throttling calorimeter fails to enable us in determining the value of dryness fraction of steam . to overcome this difficulties we make use of separating and throttling calorimeter . first the steam is passed through separating calorimeter where itlosses most of it’s moisture and becomes comparatively drier, it is than passed through the throttling calorimeter where super heating takes place with out changr of total heat . the temperature and pressure of steam after throttling are measured by using a thermometer and manometer respectively.DESCRIPTION
The set up consist of a separating and throttling calorimeter . a steam generator is provided at the base of the apparatus . a thermostat knob is provided at the front of apparatus to control the temperature inside the steam generator . steam from steam generator is passed from separating calorimeter where most of the water partical get separated from steam and then passed to throttling calorimeter where steam get superheated . after that superheated steam passed through heat exchanger to condense the steam.SAPARATING CALORIMETER
It consist of two concentric chamber , the inner chamber ,and the outer chamber . which communicates with each other through an opening at the top. As the steam discharge through the metal baskets ,which has a large number of holes , the water partical due to there heavier momentum get separated from the steam and collected in the chamber. The comparatively dry steam in the inner chamber moves up and than down aging through the annular space between the two chambers and enters the throttling calorimeter .THROTTLING CALORIMETER
It consist a narrow throat . pressure and temperature are measured by manometer and thermometer . the steam after throttling process passed through the heat exchanger and condensate is collected .UTILITIES REQURIED
1.WATER SUPPLY 3 lit/min (approx) 2.Drain 3.Electric supply : 1phase , 220 V A.C , 2Amp. 4.Steam table for calculation 5.Space required : 1.0 m X 1.0 m
Portal Frame Apparatus
DESCRIPTION:
Portal Frames used for the measurement of horizontal reaction are made stiffer by using M. S. flats rectangular cross section (10mm thick and 40mm wide). All are true to shape. The ends can be other fixed of hinged as desired. The end at which horizontal reaction, is to be measured, is provided with ball bearing rollers, which easily rolls on a smooth rolling platform. At the roller end a chord is attached which is connected further to spring balance. The spring balance records the horizontal reaction, for the measurement of slope and deflection. Both the columns of the portal frame can be clamped (fixed) or pivoted (hinged) and required.EXPERIMENT:
• To study the behavior of a portal frame under different end conditions.TECHNICAL SPECIFICATION:
• Apparatus made up of M.S. plate of rectangular section of 3mm thick x 40cm wide. • Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. • The size of portal will be 40cm x 60cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. • Apparatus is to be supplied complete with a supporting stand and a set of weights • Electronic load cells, displacement cell and Electronic Control Unit (ECU) provided with apparatus. • Software for digital calculations to easily performs by students.OPTIONAL ACCESSORIES:
• PC/Laptop Set.
Recalculating Ball Type Steering System
Recalculating Ball Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
