XTEMOS ELEMENT
AJAX PRODUCTS TABS
Water Tap, Swan Neck, Light
Plane Table
Description
The Plane Table Surveying Instruments include standard accessories like Trough Compass, Spirit level, Canvas cover, Plumbing Fork etc., and is also with a fitted tripod. Uses of Plane Table in Engineering Surveys: • Maps preparation • Recording topography Accessories included in Plane Table Surveying Instruments: • Plane Table Board 750 x 600 mm, thickness 22mm & 16mm • Carrying Bag for Board • Teak wood Polished Stand • Stand Rigid Brass Head & Plate, • Magnet Trough compass brass • Spirit Level brass • Sight van 24" • Plumbing Fork • Plumb Bob
Tuning Forks, Set of 4
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Insect Collecting Net’ Executive’ (Telescopic)
Rotary Air Compressor Test Rig
The Apparatus consists of a rotary vane compressor driven by an electric motor; Air intake is measured by an orifice meter and manometer, Discharge “pressure is measured by a pressure gauge. Power input of the compressor measured by an Energymeter. Thus the students can determine volumetric efficiency, power consumption and free air discharge of compressor.
SPECIFICATIONS:
1.Vane compressor – Rotary compressor, driven by 3 HP motor. 2.Calibrated orifice meter with water manometer to measure air intake. 3.Energy meter to measure input of the meter. 4.Pressure gauge to measure discharge pressure. 5.Control valve at delivery side. 6.Stop clock. 7.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Floor space of approx. 1.5 X 1.5 m. X 1.5 M. height. 2.440V, 16A, 3ph. supply. 3.Tachometer.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Induction Coil, Ruhmkorff
Description
Coils are wound with highly insulated copper wire impregnated with paraffin wax; input 6-8 V dc through two 4 mm socket terminals, with an adjustable trembler system. The spark suppression capacitor is housed in the base. A pair of pointer electrodes with insulated handles for adjustment of the spark gap is provided. Spark length 10 mm Spark length 25 mm Spark length 50 mm Spark length 75 mm Spark length 100 mm
Chordata Protochordata
Educational Equipments Manufacturer, Exporters & Suppliers - School Educational Equipments Manufacturers & Exporters of Educational Equipments for Lab.
Science Lab Products, Teaching Aids, Classroom Instruments, Educational Laboratory
Amphioxus Entire WM
Amphioxus Pharynx Region TS
Amphioxus Gonads Region TS
Amphioxus Intestine Region TS
Amphioxus Oral-Hood TS
Amphioxus Tail Region TS
Balanoglossus Ant. Region LS
Balanoglossus Proboscis Region TS
Balanoglossus Collar Region TS
Balanoglossus Brachial Region TS
Balanoglosus Trunk Region TS
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Calorimeter, Electric
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Mammal
Behaviour Of Column Struts Apparatus
Apparatus consist of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below:
1. Both ends pinned
2. Both ends fixed
3. One end pinned and other fixed
4. One end fixed and other end free
Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Forced Convection Apparatus
The unit consists of a circular pipe; loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe. Temperature of air at inlet and outlet of test section are measured. Thus the students can calculate local and overall heat transfer coefficients in forced convection, at various airflow rates and various heat flux values.
SPECIFICATIONS:
1.Test pipe – 32mm NB GI pipe, 500 mm. long, heated by band heater, outside. Centrifugal blower to force air through test pipe with How control valve. 2.Variac 2A, capacity to force air through test pipe with flow control valve. 3.An orifice meter with differential water manometer. 4.Voltmeter and Ammeter to measure heater input. 5.Multichannel digital temperature indicator to measures various temperatures. 6.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Bench area of about 1m. x 0.75 m. at working height. 2.239v, 15A, AC, supply with earthing connection.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Motor With Solar Cell
Optech Scanner
Description
Optech ILRIS Laser Scanner is fully portable, laser based ranging and imaging system for the commercial survey, engineering, mining and industrial markets. A compact and highly integrated instrument with digital instrument with digital image capture and sophisticated software tools, ILRIS is an industrial leading solution that addresses the needs of commercial users.
Binocular Microscope
The future of class room microscopy with crisp sharp image, very much convenient in working, easy to move, light weight, durability, ergonomic design and affordable prices.
It became an ideal instrument for school labs, medical institutes, colleges and universities.
Specifications
| Viewing head | : | Inclined sliding type Binocular Head | |
| Eyepiece | : | Paired Wide Field Eyepiece WF 10x/18 | |
| : | Paired Eye-piece 5x Huygenian | ||
| Objectives | : | Semi-Plan 4x,10x,40x(SL) & | |
| : | 100 x (SL) Oil Immersion. | ||
| Nose-piece | : | Quadruple Nosepiece | |
| Mechanical Stage | : | Double plate stage size 140mm x 140mm, X/Y travel range 90mmx65mm.Low drive right side movement controls. Ceramic surface for scratch resistance. Double specimen holder clip | |
| Condenser | : | Abbe N.A 1.25 with Iris Diaphragm | |
| Filter | : | Frosted White Filter | |
| Illumination | : | LED Illumination, Brightness Adjustable | |
| Light Source | : | Plano-concave Mirror | |
| Carrying Case | : | Styrofoam Packing with standard accessories. |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
CNC Lathe Trainer
Controller:
Type of control system: PLC based system Main Spindle Drive : AC Motor with VFD Z and X Drives : Stepper drive with Ramp function Input to Stepper : Optically Isolated Motor Drive :TTL Compatible Run Speed Control : Computer controlled with software Interpolation : liner / Circular /Parabolic Cycles Used :G,M,S,T,F,I,K,M,F Cycles : Circular Interpolation /canned Threading : Straight/Taper Power Devices : Short Circuits and over Temperature Protected Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
Center height : 100mm Swing over Carriage : 80mm Distance between Centre : 300mm Longitudinal Travel : 310mm Weight : 800kg Dimension in mm : 1300 x 800 x 1400 Rapid Travel : 700mm/min Resolution Z Axis : 5micron Resolution X Axis : 5micron Automatic : providedAXIS TRAVEL:
X Axis : 80mm Z Axis : 310mmSPINDLE:
Spindle Speed : Continuous Variable Spindle Power : 2 HP Inside Taper : MT3 Speed Range : 50 to 3000Rpm
Histology Set I
Set of 24 slides comprising
| Adipose tissue | Compact bone |
| Striated muscle, teased | Nerve cells isolated |
| Spinal cord | Aorta, artery and vein |
| Human blood smear | Liver |
| Pancreas | Pseudostratified caliated columnar epithelium of trachea |
| Stomach | Simple columnar epithelium |
| Squamous epithelium | Lleum |
| Duodenum | Human Scalp |
| Smooth muscle | Kidney |
| Ovary | Rat Testis |
| Lung | Injected small intestine |
| Effector nerve ending | Cardiac muscle |
Air Core Solenoid
Description
Air Core Solenoid helps investigate the magnetic field of a long coil. It can also used with the Current Balance as an accessory to measure the force on a conductor in a magnetic field. The solenoid has coils wound on a plastic tube with approximately 575 turns of copper wire. It can carry a current of 5 A continuously or 10 A intermittently.
Episiotomy Training Simulator
Description
Suturing Simulators provide a realistic way for students to learn good surgical techniques. The simulators provide students with a variety of repair experiences without the constraint of time and concern for safety, which are factors with a live patient. The simulators can be used by the student in a learning lab with an instructor or by the student individually in the clinical setting just prior to a patient experience. They are also useful as homework teaching aids that can be signed out at night and returned the next day. In addition to being portable, the lifelike texture allows the learner to develop a “feel” for instrument handling, tension on suture, and the advantages of one method of tying knots over another.Includes one of each simulator:
Midline Suture Simulator Left Mediolateral Suture Simulator Right Mediolateral Suture Simulator Each simulator comes with an instruction booklet and is individually boxed.
