XTEMOS ELEMENT
AJAX PRODUCTS TABS
Rear Axial Assembly With Differential Gear
Rear Axial Assembly With Differential Gear Fully Floating Type – Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Ruhmkorff Coil
Description
Ruhmkorff Coil produces pulses of high voltage spark from low voltage DC source (6 – 12 V DC). It is suitable for use with gas-filled discharge tubes, vacuum tubes, eudiometers and for general laboratory work. Includes an adjustable vibrator system, primary current polarity reversal, on-off switch, a capacitor enclosed in the box and special alloy contacts. Spark gap at the discharge points can be adjusted by sliding rods back and forth. Spark Length 15 mm.
Planck’s Constant
Modern LEDs (light emitting diodes) cover the range from deep blue (440 nm) to infra-red (940 nm). By monitoring the voltage at which each LED just begins to emit light a graph of energy input as a function of light emitted frequency can be plotted and an approximate value of Planck’s constant deduced. Complete with viewing tube but without power supply.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Measuring Jugs
The Measuring Jugs, moulded in Polypropylene are clear, autoclavable and have good chemical resistance.
The Measuring Jugs are provided with a handle for easy & convenient lifting and have raise graduations for easy reading.
Adding to the existing range of Jugs, these short form transparent jugs, made of polypropylene are autoclavable and have non-drip spout.
These jugs have raised graduations, provide excellent contact clarity, & are provided with excellent thumb grip on handle.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Measuring Jug 250 ml | 12 | |
| Measuring Jug 500 ml | 12 | |
| Measuring Jug 1000 ml | 6 | |
| Measuring Jug 2000 ml | 6 | |
| Measuring Jug (Euro Design) - 500 ml | 12 | |
| Measuring Jug (Euro Design) -1000 ml | 6 | |
| Measuring Jug (Euro Design) - 2000 ml | 6 | |
| Measuring Jug (Euro Design) - 3000 ml | 6 | |
| Measuring Jug (Euro Design) - 5000 ml | 4 | |
| Measuring Jug (Printed Graduation) - 100 ml | 12 | |
| Measuring Jug (Printed Graduation) - 250 ml | 12 | |
| Measuring Jug (Printed Graduation) - 500 ml | 12 | |
| Measuring Jug (Printed Graduation) - 1000 ml | 6 | |
| Measuring Jug (Printed Graduation) - 2000 ml | 6 | |
| Measuring Jug (Printed Graduation) - 5000 ml | 4 |
Endocrine Glands
Ruhmkorff Coil
Description
Ruhmkorff Coil produces pulses of high voltage spark from low voltage DC source (6 – 12 V DC). It is suitable for use with gas-filled discharge tubes, vacuum tubes, eudiometers and for general laboratory work. Includes an adjustable vibrator system, primary current polarity reversal, on-off switch, a capacitor enclosed in the box and special alloy contacts. Spark gap at the discharge points can be adjusted by sliding rods back and forth. Spark Length 15 mm.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Citical Radius Of Insulating Material
Citical Radius of Insulating Material:
At particular radius of insulation over a cylinder, loss of heat is maximum. The unit consists of a G.I. pipe provided with plaster of Paris insulation on out side surface. Four pipes are provided with heater inside having input control. Input to heaters is measured by common voltmeter and ammeter, by controlling input to heaters, it is shown that critical radius of insulation is ratio of thermal conductivity and outside heat transfer co-efficient.
SPECIFICATIONS:
1.G. I. Pipes with electrical heater inside – 4 Nos. 2.Insulation over the pipes of different thickness. 3.Controls and Measurements – a) Dimmerstat to control heater input – 4 Nos. b) A voltmeter and ammeter to measure inputs to heater. c) Digital temperature indicator to measure temperatures across insulation. d) Necessary switches and controls. A technical manual accompanies the unit.SERVICES REQUIRED:
230 V, 5 Amp., A.C., Supply with earthing connection. Floor Area of 1 m. X 1 m X 1.5m. height.
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Specific Gravity Specimen Cylinders with Hooks
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
PCR Tube Rack
We are one of the prime Exporters and Traders of PCR Tube Rack .
Used for keeping PCR Tubes, Top & base of this rack are made of tough & transparent polycarbonate while the middle portion is made of polypropylene.
PCR Tube Rack facilitates the use of multipipetters.
A number of racks can be stacked together to save shelf space.
Material : Polycarbonate / Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| PCR Tube Rack (Rack for 96 PCR Tubes of 0.2 ml | 4 |
Two Stage Air Compressor Test Rig
The test rig comprises of a two-stage air compressor fitted with an air tank with orifice, pressure gauges 9 an energy meter to measure the input & a Temperature indicator measures the temperatures at various points. The compressor is mounted on air receiver along with the motor, and is provided with air relief valve (safety) and a pressure switch. The unit determines volumetric efficiency and isothermal efficiency at various discharge pressures
SPECIFICATIONS:
1.Air compressor – Double cylinder, two-stage type driven by a 2-hp. Three – phase motor mounted on air receiver provided with delivery valve. 2.Air tank and orifice with water manometer for air intake measurement. 3.Pressure gauges at outlet on both stages. 4.Digital temperature indicator. 5.Energy meter to measure input power. 6.A technical manual accompanies the equipments.SERVICES REQUIRED:
1.Floor space of 2,5 X 1.5m. 2.440 V, 15A, 3ph. AC supply with neutral and earthing connection. 3.A hand tachometer.
Human Tooth, Upper Triple Root In 6 Parts
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
IoT Development System
The industrial networks are primarly concerned with Programmable Logic Controllers(PLC),Distributed Control Systems(DCS), Supervisory Control and Data Acquistion Systems(SCADA) any many other hetrogenous devices in the form of differnt applications. More over these devices are based on either wired or wireless communication protocols like Profinet, Profibus, MODbus, WiFi, Zigbee and Etc.
Specification:
• To impart the knowledge about Industrial IoTa the Students, We have designed a IIOT trainer kit, which have inter-quark chip based IoT Gateway. • This Gateway is a universal Gateway supports many different types of communication protocols such as wired and Wireless communication for industrial applications. • The IIoT Gateway connected with Siemens based Distributed Control System(DCS), Programmable Logic Controller(S7-1200, S7-1500) using S7-protocol and OPC UA. • The Intel centrino based powerful WiFi chip enables us to the access data via Mobile Application. • The Gateway can get the internet connectivity via Ethernet and WiFi also. • This Gateway can communicate with our own ingenious data acquisition system using RS485 BUS and RS232 Bus. • The USB based communication exchange the data between Zigbee co-coordinator and Gateway.
Tablet Coating Pan
Product Description
We offer coating pan that is designed to perfection and fabricated from best grades of raw material procured from reliable sources. These coating pan are suitable for coating tablets and is checked by our quality controllers for high performance and uniform coating all over the tablet. The different parts of our coating pan machines are listed as under:PAN
The coating pan is SS semi ellipsoidal size pan with a circular mouth for charging & discharging of tablets, Pan mounted at an inclination of 45 degrees to the horizontal.DRIVE ASSEMBLYPAN
The tablet coating pan consists of a suitable HP 3 Phase, 440 V, 1440 RPM TEFC motor with suitable worm reduction gear box and cone pulley arrangement to give three speed output.HOT AIR BLOWERPAN
The tablet coating pan unit is provided with a hot air blower consisting of suitable HP 3 Phase 440 V, 2880 RPM TEFC electric motor & centrifugal blower with damper delivering required CFM. The air is heated by means of suitable electric heater to give air at 30 to 90 degrees Heater with thermostat control and flexible hose pipe.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Petri Dish
These Petri Dish offered by us is clear, unbreakable, & autoclavable.
The PS Petri Dish with fitting proves excellent for culture exp.
Made in polystyrene, this transparent Petri Dish provides an excellent inside view.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Petri Dish 50 mm | 36 | |
| Petri Dish 75 mm | 36 | |
| Petri Dish 100 mm | 36 | |
| Petri Dish 125 mm | 12 | |
| Petri Dish 150 mm | 12 | |
| Petri Dish (Culture) | 12 |
Advanced Surgical Suture Arm
Description
Interchangeable arterial and venous inserts within the fore arm allow creation of arteriovenous (AV) fistulas and placement of AV grafts, while a simulated healed fistula insert provides a platform on which hemodialysis exercises can be performed. An additional multi-layer insert in the bicep area can be used for incision and suture training exercises.Advanced Arterial Patient Training Arm Features:
Subcutaneous injection sites on the volar forearm and lateral upper arm Intra Muscular injection site on the upper arm Arterial system including the radial and brachial arteries Suture and incision sites on both the upper arm and forearm Hem dialysis site on the forearm Arterial and Venous insert for IV and blood draw exercises, AV anastomosis, and placement of AV grafts. This multi-layer surgical insert includes the skin, subcutaneous tissue, muscle, radial artery, and radial vein AV fistula insert that simulates a healed fistula for hem dialysis exercises. Multi-layer bicep insert that includes the skin, subcutaneous tissue, and muscle and allows incision and suturing exercises Durable skin that can be pierced in excess of 200 times with a 20 or 22 gauge needle Realistic tactile feedback for both surgical and arterial & venous stick exercises Adjustable heart rate and pulse strength simulating a heart rate from 10 BPM to 150BPM Cephalic (antecubital), Basilic, Radial, and Ulnar veins as well as the radial and brachial arteries for infusion and blood draw. Rotating arm allowing dorsal and volar access along the length of the arm. Varying vessel palpability to simulate collapsed or bulging vessels and ease of assembly. Latex-Free New proprietary materials replicate of skin, subcutaneous, and muscle layers at all surgical sites. Upgraded inserts, skins, and vessels for improved tactile feedback Micro pump embedded within the shoulder generates variable heart rates and pulse strength. Easy to replace plug-and-play inserts to allow quick change-out between procedures. Latex-free vessels with improved access for hassle-free replacement.
Heat Pipe Apparatus
Heat Pipe Apparatus:
Heat pipe is an interesting device, which is used to transfer heat from one location to another.
The apparatus consists of three pipes, viz. A heat pipe, copper pipe and stainless steel pipe. Ail the pipes have same physical dimensions. Copper and stainless steel pipes serve the purpose of comparison of heat pipe performance. All pipes are mounted vertically with a band heater at lower end and water filled heat sink at upper end. Nearly isothermal operation of heat pipe is clearly visualized from longitudinal temperature distribution of the pipe.
SPECIFICATIONS:
1.Heat pipe – Stainless Steel pipe, 25 mm O.D., 450 mm. Long. Sealed at both ends, evacuated and filled partially with distilled water – one No. 2.Copper and stainless steel pipe of same size as that of heat pipe – one each. 3.Equal capacity heater at bottom end of each pipe. 4.Water filled heat sinks at upper end of each pipe.Measurements and controls
a) Dimmerstat to control heat input to all the heaters – 4 amp. Capacity One No. b) A voltmeter and an ammeter to measure input to heaters One each. c) Multichannel digital temperature indictor to measure temperatures along the length of pipes.Four thermocouples are provided on each pipe. v Thermometers to note down water temperatures in heat sinks – 3 Nos.Services Required:
230 VA.C. Single Phase supply. Floor Area = 1 m X 0.5m X 0.5 m height.
Primary and Secondary Coil
Description
The apparatus demonstrates the principle of Electromagnetic Induction and helps explain the concept of a transformer. Primary and Secondary coil consist of coils mounted on plastic spools, with 2 binding posts on each coil. You can slide the primary coil inside the secondary coil. Also includes a soft iron core for induction experiments. Primary coil has 480 turns while secondary coil has 3800 turns. Requires a galvanometer and bar magnets, not supplied with apparatus.
Cytology Mitotic Cell Division
Educational Equipments Manufacturer, Exporters & Suppliers - School Educational Equipments Manufacturers & Exporters of Educational Equipments for Lab.
Science Lab Products, Teaching Aids, Classroom Instruments, Educational Laboratory
Interphase Stage
Prophase Stage
Metaphase Stage
Anaphase Stage
Anaphase Stage
Telophase Stage
Set of 5 Slides, as above
