XTEMOS ELEMENT
AJAX PRODUCTS TABS
Spartan 6 Trainer Kit
Features
• 16 Nos. of digital input using slide switches with LED indication • 16 Nos. of digital output using discrete LEDs • 16× 2 LCD is provided for display the text message. • One Reset Switch • One switch for giving manual clock • FPGA configuration through - On board Xilinx USB to JTAG Programmer with isolation to configure FPGA - On board Flash Prom XCF04S (Programmable through USB to JTAG programmer) • Total 186 I/O Pins: 100 Pins used for integrating peripheral like LED, Switches etc., balance pins are available to user • In 3nos of 20 pin header. • 1 No of 26 pin header to interface VLIM cards like Traffic Light Controller / On-board TLC (factory settable). • On board programmable PLL oscillator from1 MHz to 100MHz using jumpers • 4Nos of 7 segment LED display • One relay and Buzzer provided. • Stepper & DC motor drive provided on board (Motor Optional) • 4x4 matrix key provided • On board I2 C RTC Interface • On board Temperature Sensor Interface • SPI Based Analog to Digital Converter
pH, Conductivity and Temperature Meter, Digital, Table Model
Highly stable and accurate.
Cell Constant Adjustment Facility
3.5 Digit Red LED Display
Technical Specification
General Power: 220 V AC ± 10%, 50Hz Dimensions: 75 x 175 x 275 mm (App.) Weight: 2.5 Kg. (App.) Temp. Compensation: 0 to 50°C adjustable from temperature. Parameters pH Range: 0 - 14 pH Resolution: 0.01 pH Accuracy: ± 0.01 pH ± 1 Digit Temp. Compensation Manual: 0 to 100°C Temperature Range: 0 - 100°C Resolution: 0.1°C Accuracy: ± 0.2% ± 1 Digit Sensor RTD: (PT - 100) Conductivity Range: 0 to 20 mS/cm in two Ranges Accuracy: ± 0.5% ± 1 Digit Resolution: 1µS/cmAccessories
pH combination electrode Cond. Cell Temperature probe Operation manual Dust cover pH stand 7 & 4 pH bottles Beaker
Microscope Glass Slides – Plain
Magnetic field demo, vertical wire
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Cylinderical Magnet
Coelenterata
Solar System Model
LPC 2148 Evaluation Board
ON Chip Features
• CPU - LPC2148. • Core - 16/32 Bit ARM7TDMI-S. • Speed - Max 60 MHZ. • Flash - 512KB. • RAM (on-chip) - 40KB. • 46 x General Purpose I/O Pins. • USB2.0 Full speed Compliant Device. • One 10bit ADC with 14 Analog inputs. • One 10bit D/A Converter. • Two 32bit Timers/ External Event Counters. • Low Power Real Time Clock. • Six PWM, Watchdog. • Two UARTS (16c550). • Two Fast I2C (400Kb/s) Module.ON Board Features
• Eight Digital Output - LED Interface. • Two Digital Input. • 16 x 2 Character LCD Interface. • 7 Segment Display via I2C Interface. • 10 Base T Ethernet Connectivity. • SD Card Interface Support. • Audio Interface. • Jtag connector is provided for Debugger. • USB to serial interface provided.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Hydraulic Drum Brake Actual Working Four Drum
TMS320F2812 Based DSP Trainer
FEATURES:
• 12 Motor control PWM & 4 Individual PWM output • 16 channel, 12 bit ADC • 56 Individually programmable GPIO lines • 2 Quadrature encoder interface / 6 capture input • 128K x 16 bit flash memory • 1K x 16 bit OTP ROM • 14K x 16 bit SARAM • 16 LEDs are provided for user program development & debug • Opto isolated USB to Serial Interface • 3 Switches are provided for user interface like, frequency, speed variations etc., • Bead Inductances provided for RF EMI rejection • 16 ADC inputs are protected and terminated at 26 Pin FRC connector. • 8 I/O lines are protected and terminated at 50 Pin FRC connector • 12 PWM outputs and 6 capture inputs are terminated at 34 pin FRC connector • On board isolated USB to JTAG interface
Motor Generator Model Set
Description
This motor-generator set gives students an insight into the physical and technical relationships on which electric motors, generators and transformers are based. The modular system allows to set up different function models without tools: Various DC motors Series and shunt motor Synchronous motor DC generator and alternator Transformer. This set allows the performance of 10 student experiments about the following topics: Magnetic field of a coil Conversion of electrical energy into kinetic energy Commutator Direct current motor Synchronous motor Series and shunt-wound motors Electromagnetic induction The electrical generator Engine-generator Transformer
Worm Roller Type Steering System
Steering System – Actual Working
Manual Steering System
Type – Worm & Roller Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Signal Generator, Digital
This signal generator is a useful test instrument capable of generating multiple waveform and offers excellent waves shape, signal linearity, waveform symmetry and frequency range with selection of sine, triangular and square wave and amplitude variable 10 V peak to peak. 1 Hz to 100 kHz in five decade ranges selected by rotary switch named as frequency multiplier. Sine, triangular and square waveforms selected by push switch with LED indication. Output signal is 0 – 3.5 Vrms (10 V peak to peak) open circuit continuously control with uncalibrated amplitude control knob. Mains rocker switch with indicator Light. Signal Generator is versatile for general laboratory use; output signal is adjustable with the combination of frequency multiplier and set frequency dial with a low level of distortion. Set frequency is displayed on a 4 seven segment display. Output Voltage is continuously variable with selector range 1 V and 10 V.There is two pair of output safety sockets. One for CRO output (experiment for amplification, filter etc.) and another pair of sockets to speaker to drive a speaker and to demonstrate the audio signal frequency range 20 Hz to 20 KHz.
Histology Set II
Set of 24 slides consisting of
| Adrenal gland | Areolar tissue |
| Cereburm | Colon |
| Compact bone, LS | Heart, entire LS |
| Human plantar skin | Hyaline cartilage |
| Kidney, LS | Liver, injected |
| Lung, LS triple stain | Lymph node |
| Olfactory epithelium | Oviduct |
| Penis | Peripheral nerve |
| Pituitary, V.LS | Sperm Smear |
| Striated muscle, TS | Thyroid gland |
| Tooth | Trachea |
| Ureterv | White Fibre-Cartilage |
4 Stroke 1 Cylinder Petrol Engine Manual Driven
The engine will be sectioned to show the internal constructional details. The working of individual part and accessories like Valves, Pistons, pumps, Crank and Camshaft, etc. will be demonstrated. It is provided with Flywheel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes. The actual cut section engine will be supplied with key card & very interesting literature regarding working.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Masses, Slotted
Solid brass, Accurate machined masses placed on a plastic and metal rack with handle.
Set of 8: 1x10 gm, 2x20 gm, 1x50 gm, 1x100 gm, 2x200 gm, and 1x500 gm, Total 1100 gm.
Set of 10: 1x10 gm, 2x20 gm, 1x50 gm, 5x100 gm, 1x500 gm, Total 1100 gm.
Set of 12: 1x1 gm, 2x2 gm, 1x5 gm, 1x10 gm, 2x20 gm, 1x50 gm, 1x100 gm, 2x200 gm, 1x500 gm, Total 1110 gm.
Set of 14: 1x1 gm, 2x2 gm, 1x5 gm, 1x10 gm, 2x20 gm, 1x50 gm, 5x100 gm, 1x500 gm, Total 1110 gm.
Beaker (Polypropylene)
We are the renowned Exporter and Trader of high quality Beaker (Polypropylene).
These Polylab Beakers, molded in Polypropylene, have excellent clarity and very good chemical resistance.
These autoclavable Beaker (Polypropylene) have prominently raised graduations on the outer surface.
Pouring a solution becomes very convenient because of its tapered spout.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Beaker 50 ml | 12 | |
| Beaker 100 ml | 12 | |
| Beaker 250 ml | 12 | |
| Beaker 500 ml | 12 | |
| Beaker 1000 ml | 6 | |
| Beaker 2000 ml | 6 | |
| Beaker (Euro Design) 25 ml | 12 | |
| Beaker (Euro Design) 50 ml | 12 | |
| Beaker (Euro Design) 100 ml | 12 | |
| Beaker (Euro Design) 250 ml | 12 | |
| Beaker (Euro Design) 500 ml | 12 | |
| Beaker (Euro Design) 1000 ml | 6 | |
| Beaker (Euro Design) 2000 ml | 6 | |
| Beaker (Euro Design) 5000 ml | 2 | |
| Beaker (Printed Graduation) 50 ml | 12 | |
| Beaker (Printed Graduation) 100 ml | 12 | |
| Beaker (Printed Graduation) 250 ml | 12 | |
| Beaker (Printed Graduation) 500 ml | 12 | |
| Beaker (Printed Graduation) 1000 ml | 6 | |
| Beaker (Printed Graduation) 2000 ml | 6 | |
| Beaker (Printed Graduation) 5000 ml | 2 | |
| Beaker (Printed Graduation) 10000 ml | 2 |
Human Reproduction Charts
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tearable and long lasting with plastic rollers, size 75 x 100 cm. Human embryological development. Human Life cycle (birth). Human reproductive organs, male. Human reproductive organs, female.
Ripple Tank
Description :-
Transparent acrylic plastic ripple tank, supported in a sturdy plastic frame which has recesses to hold four legs with leveling feet.
The tank edges are shaped to minimize undesired reflections.
Tank has a drain hole closed by a rubber stopper.
With two light alloy uprights to carry a horizontal rippler support rod which is adjustable for height.
The ripple assembly, elastically suspended from the support rod, consists of a 4 – 6 V DC motor mounted on a wooden beam.
The motor has an eccentric weight which causes the beam to oscillate.
Two point sources are provided by two plastic spheres, each mounted on a right angle rod.
A metal rod is fixed centrally into a socket in one short side of the frame to afford support to the illuminant.
Overall size of the tank 580 x 500 x 80 mm, window area 370 x 280 mm, height of tank above bench level (with legs attached) approx. 375 mm.
Complete with following accessories :-
1. Two straight obstacles of aluminium alloy length 130 mm.
2. One straight obstacle length 40 mm.
3. One curved reflector radius 200 mm.
4. One trapezoidal plastic plate for refraction.
5. One wood hand wave roller.
6. One water dropper.
7. One pkt. rubber bands.
8. One foam plastic sponge.
9.One illuminant with a 12 V, 24 W lamp mounted in a lamp house and provided with a long supporting rod.
Bar Breaking Apparatus
Description
A heavy cast iron stand slotted to carry a stout iron bar, with ten cast iron breaking bars. Comprising a heavy cast iron frame 340 x 120 x 100 mm with slotted end pillars to carry a stout iron bar. The bar is threaded at one end for a large tensioning nut and has holes at the other end to accommodate the cast iron breaking bars. Supplied complete with ten breaking bars.
Primary and Secondary Coil
Description
The apparatus demonstrates the principle of Electromagnetic Induction and helps explain the concept of a transformer. Primary and Secondary coil consist of coils mounted on plastic spools, with 2 binding posts on each coil. You can slide the primary coil inside the secondary coil. Also includes a soft iron core for induction experiments. Primary coil has 480 turns while secondary coil has 3800 turns. Requires a galvanometer and bar magnets, not supplied with apparatus.
