XTEMOS ELEMENT
AJAX PRODUCTS TABS
Solar Wind 3Φ, 2KW Smart Grid
This consists of 2 Microgrids of 2000W &1000W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. A 3Φ 3KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 3Φ, 2.5KVA Grid Commercial Solar Power Inverter can be added to this experimental setup. By adding 3Φ, 2.5KVA commercial solar inverter, when the experimental setup is not used by student, it may be used to generate power.
This Advanced Smart Grid Experimental Setup Consists of
• 2 Micro Grids, each 1000W of power generation using Solar, Wind or Hybrid • An Isolation Transformer Coupled to the utility Grid, acts as Main Grid to this Setup • Various other Power Sources • Commercial 3Φ 5KVA Grid Connected Inverter (Optional) • Optional Components for the Smart Grid Setup • DSP /FPGA Controller for PE, SG, PS Applications • Other Add ons • Components for Building 10/25KW Smart Grid Power Generation • IoT Based Data Acquisition.Solar Wind Grid Connected 3Φ, 2KW Smart Micro Grid
• Main Frame • 1KW Solar PV Module with Stand • Wind Turbine • DC-DC Boost Converter • 120V Battery Bank - 12V x 100AH x 10 Nos • 2KW Bi-Directional DC-DC Buck-Boost Converter for Charging battery • 2KW 3Φ Inverters • DSP/FPGA Controller • Microcontroller based Protection Relays • Smart Energy Meter • Synchronizing Panel • Three Phase RL Load 2KW • PLC with SCADA Software • 14 Channel PC based Power Quality Analyzer (Optional)
Intestinal Villi
STAINING RACKS
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Plates For Simple Cell
Resonance Apparatus
Insect Storage Box
Description
For pinning of insects both inside top & bottom, White hardwood / Teakwood frame with melamine lamination on top & MDF sheet bottom is nicely polished. Top & bottom lined with 8mm thick soft pinning. washable EVA sheet. Inside glazed white. Raised wall with holes for insecticide inside bottom to make box air tight and pest proof. Fitted with brass hinges. index card holder & clips. Insect Storage BoxSize 53x45x9 cm Insect Storage BoxSize 45x30x7.5 cm Insect Storage BoxSize 38x25x7.5 cm Insect Storage BoxSize 30x23x7.5 cm
Line Shaft Unit
Description
For showing the conversion from electrical energy via mechanical, to potential energy by winding up a weight on a cord. One end of the 6mm. steel shaft carries an aluminium 'V' pulley 56 mm. diameter, and the other end is fitted with a cord anchoring collar. Supplied complete with driving belt.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Three Phase Cyclo Converter
This module is designed for three phase half wave-step down cycloconverter. It consists of 18 Synchronized firing pulses, 18 SCRs, Relevant power supply and circuitry for frequency divisions.
Specification
• Eightin nos. SCR with RC snubber protection is provided for 3phase • cycloconverter power circuit (each phase consist of 6 SCRs) Rated at 1200V@25Amps. • Three nos. center tapped inductor (0%.50%, 100%) is provided for power circuit. • Eightin nos. Isolated gate pulses for SCR power circuit. • One potentiometer is provided to vary the frequency. • One potentiometer is provided to vary the output voltage. • MCB protection. • Housed in sleek screen printer cabinet. • Provision for V/F control Power Supply. • Input 440V ± 10%, 50HZ three phase AC supply. • ± 15V DC, 9V, 9V, 9V AC (3phase) for the firing circuits. • 24-0-24V 3phase input for power circuit.
Botany
Algae Fungki, Set of 20 slides
Angiospermic Families, Set of 15 slides
Bacteria, Set of 20 slides
Bacteria, Algae & Fungi, Set of 30 slides
Botany, Set of 30 slides
Bryo & Pteridophyta, Set of 20 slides
Cell Structure, Set of 20 slides
Dispersal of Seeds, Set of 20 slides Fern, Set of 10 slides
Fruits, Set of 20 slides
Germination of Seeds, Set of 20 slides
Higher Plants, Set of 20 slides
Inflorescence, Set of 20 slides
Insectivorous & Parasitic Plants, Set of 20 slides
Single Phase Cyclo Converter
Specification
• Consists of firing circuit, SCR power circuit and load. • Line synchronized IC based linear firing circuit. • Line synchronization achieved by step - down transformer. • Four nos. firing pulse with pulse transformer isolation to trigger four SCR. • One no. potentiometer used to vary the firing angle (180° - 0°). • Carrier logic implemented with carrier frequency of 4KHz. • One no. toggle switch with debounceogic for pulse ON/OFF. • EPROM Based firing pulse frequency variation. • Two nos. toggle switch to select different frequency (Hz, 50/2Hz, 50/3Hz, 50/4Hz). • Power circuit consists of Four nos. SCR with fuse protection. • Anode, Cathode, Gate terminals are terminated in the front panel for user connection. • 24V AC, 1Amp Provided for power circuit input with ON/OFF switch. • One no. fixed R, load provided Center tapped inductor for power circuit. • 230V, 50Hz AC input with ON/OFF rocker switch, fuse for over load.
Automobile Parts Actual Cut Section
This model helps the student to understand the working of automobile parts very easily. It is specially made dissectible for demonstration purposes.
1 Self Starter
2 Battery
3 Distributor
4 Ignition Coil
5 Spark Plug
6 Magneto
7 Electrical Fuel Pump
8 Mechanical Fuel Pump
9 Master Cylinder
10 Brake Cylinder
11 Gear Lubricating Pump
12 Water Pump or Water Body
13 Radiator
14 Crank Shaft
15 Cam Shaft
16 Connecting Rod
17 Piston With Rings
18 I.C. Injector
19 Speedometer
20 Shock Absorber
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
4 Stroke Petrol Engine Sectional Working Model
Unsymmetrical Bending Apparatus
DESCRIPTION:
Apparatus consist of an angle of size 1” x 1” x 1/8” or in equivalent metric units of length 80cm is tied as a cantilever beam. The beam is fixed at one end such that the rotation of 450 intervals can be given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement is provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end. A dial gauge with magnetic base is supplied with the apparatus.EXPERIMENT MANUAL:
• To study the behavior of a cantilever beam under symmetrical and unsymmetrical bending. • Using a Dial gauge shown a increasing and decreasing of heights.
Matt White Screen
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Bending Moment & Shear Force Apparatus
INTRODUCTION:
Shear Forces occurs when two parallel forces act out of alignment with each other. For example, in a large boiler made from sections of sheet metal plate riveted together, there is an equal and opposite force exerted on the rivets, owing to the expansion and contraction of the plates. Bending Moments are rotational forces within the beam that cause bending. At any point within a beam, the Bending Moment is the sum of: each external force multiplied by the distance that is perpendicular to the direction of the force.EXPERIMENT MANUAL:
1. To verify the Shear force a cross-section of the beam. 2. To verify the bending moment in cross–section of beam with a flexure condition.APPARTUS SPECIFICATION:
1. Dimensions : 158 cm X 45cm X (h)60cm 2. Total Beam Length : 160 cm with flexure 3. Width of Beam : 5 cm 4. Distance of Length in between : 5 cm 5. Height of beam : 36 mm 6. No. of Hanger for weights : 3 7. No. of Spring Balance : 2 (of 10kg) 8. Total Weight of Apparatus : 13.1 kgACCESSORY REQUIRES:
1. Shear force apparatus 2. Bending Moment Apparatus 3. Hangers 4. Weights 5. Two Spring balances – 10kgs
Cryo Rack
Our Cryo Rack is moulded in polycarbonate making it tough, durable & autoclavable.
This handy Cryo Rack can hold 50 vials can be unscrewed without actually picking them up as the vial will lock in every well and hence will not twist.
This rack is provided with four anti skid rubbers & each well is identified with an alpha-numeric index.
Material : Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Cryo Rack | 2 |
Spherometer Demonstration Model
Friction In Pile Lines Apparatus
DESCRIPTION:-
The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the losses due to fiction in pipes Ø To determine the friction factor for Darcy Weis back equationUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pipes (2 Nos.) : Material GI of ½ “ & 1” Diameter Ø Pipe Test Section : Length 1 m Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 25 Ltrs. Ø Sump Tank : Stainless Steel, Capacity 50 Ltrs. Ø Stop Watch : Mechanical / Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted StructureXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Wooden Lever Apparatus
Made of wood, one meter long graduated scale is balanced on knife edge of the fulcrum. Supplied with 2 sets of 100 g weights.
One meter long with fulcrum lever is graduated in centimeters and is balanced on the fulcrum by a transverse groove cut midway in the length of the lever over knife edge of the fulcrum, supplied with 2 sets of 100 g weights.
Porcelain Crucible
Description
Porcelain Bottom Crucible with porous disc permanently formed into walls. Porcelain Crucible, which we offer, is featured by stable porosity and rate of flow. These Porcelain Crucibles are made available with very fine (1.2 micron), fine (5 micron) and medium (15 micron) pore diameters discs. Maximum operating temperatures for Porcelain Bottom Crucible range from 900Â °C to 1200Â °C depending upon ceramic composition selected. Further, variation in temperature will not affect characteristics within their working temperature range.Capacity
15 ml 25 ml 30 ml 50 ml
Differential Gear Assembly Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Multi-Functional Nursing Simulator (Female)
Description
Designed according to the demand of the clinical principles and the guidelines of nursing training. This multifunctional simulator could simulate an actual circumstance for practice. Multiple functions, rural practice, easy assembly, well shaped appearance and correct anatomical landmarks provides a very good training for practice.Features:
Head Care. Body care. Patient moving. Different lying pose. Bilateral and Unilateral oxygen inhalation. Atomization inhalation therapy. Nasal Feeding. Gastric lavage training. Intravenous Injection. Intramuscular Injection. Hypodermic Injection. Various fistula orifice washing practice. Female Catheterization. Female Bladder Washing. Enema Treatment. Simulator Assembly.
Fluid Mechines Hydraulic Machines Models
FLUID MECHANICS & HYDRAULIC MACHINES MODELS
1. Hook Gauges
2. Venturimeters & Orificemeters
3. Manometers
(A) Pitot Tube
(B) U Tube Double Column Manometer
(C) Differential Manometer
(D) Inclined Manometer
4. Valves Models
(A) Hydraulic Non Return Valve
(B) Gate Valve
(C) Globe Valve
5. Turbines & Pumps Models
(A) Different Impellers Of Pumps And Turbines (Set Of 8) :
(i) Mixed Flow Runner Cast Aluminium
(ii) Axial Flow Runner Cast Aluminium
(iii) Radial or Centrifugal Runner Cast Aluminium
(iv) Kaplan Runner Cast Aluminium
(v) Francis Runner Cast Aluminium
(vi) Domestic Self Pumping Runner of Brass
(vii) Centrifugal Runner Actual Cast Iron
(viii) Pelton Wheel Runner Cast Aluminium
(B) Display Board For Pipes
(C) Hydraulic Elevator:
(D) Hydraulic Ram Non Working Model
(E) Pelton Turbine Model
(F) De-Lavel Turbine Model
(G) Kaplan Turbine Model
(H) Francis Turbine Model
(I) Impulses Turbine Working Model
(J) Air or Steam Pressure Turbine Model
(K) Pure Reaction Turbine Model
(L) Radial Turbine Model
(M) Gear Pump Model:
(N) Rotary Pump
(O) Centrifugal Pump : Actual Cut Section
(P) Reciprocating Pump : Actual Cut Section
(Q) Model Of Air Lift Pump Model
(R)Pendulum Pump Model
(S) Archemedian Screw Pump Model
(T) Tubewell Model :
(U) Deep well Turbine Pump Model
(V) Submersible Pump Model
(W) Hydro-Electric Power Installation Model
