XTEMOS ELEMENT
AJAX PRODUCTS TABS
Lab Tubing Connectors
We are engaged in providing high quality range of Lab Tubing Connectors.
These Lab Tubing Connectors are sourced from highly reliable manufacturers who ensure the usage of high grade components for its manufacturing.
Our clients have always appreciated our range of Lab Tubing Connectors for its supreme quality and durability.
our Lab Tubing Connectors comes in a wide range which includes Cross Connector , Y Shaped Connector , L Shaped Connector and T Shaped Connector.
| Particulars | Pack (Pcs) | |
|---|---|---|
| T-Connector 6 mm | 36 | |
| Y-Connector 6 mm | 36 | |
| T-Connector 8 mm | 36 | |
| Y-Connector 8 mm | 36 | |
| T-Connector 10 mm | 36 | |
| Y-Connector 10 mm | 36 | |
| Cross Connector-6 mm | 36 | |
| Cross Connector-8 mm | 36 | |
| Cross Connector-10 mm | 36 | |
| L Connector-6 mm | 36 | |
| L Connector-8 mm | 36 | |
| L Connector-10 mm | 36 | |
| Pinch Clip | 12 |
IPM Based Power Module
Power Module is designed for Motor control Applications upto 3 HP by using IGBT & DIODE Technology Based IPM. Input:1 Phase / 3 phase 50 Hz AC. Output : 400V/10A (MAX), AC/DC on each Leg of 3 phase Bridge
FEATURES:
• 1200V, 25A, 3 Phase IGBT Inverter Bridge • 1200V, 10A IGBT for Over Voltage breaking • Built - in Over Voltage, Under Voltage, Over Current & Over Temperature ProtectionADDITIONAL FEATURES:
• 1200V, 25A Converter Bridge for AC-DC power conversion • 4 Nos of Hall Effect current sensors are provided to sense the DC Link current & 3 output current of the Inverter Bridge • 1 No of Hall Effect Voltage sensor is provided to sense DC Link voltage • All the PWM signals are isolated using Opto Isolator • Protection circuit for over current with LED indication • Optically Isolated Fault signal from the IPM is given to the Embedded/DSP controllers for protection. • Independent Power supplies for all Isolated circuits. • 0-900V Voltmeter is provided to Indicate the DC Link Voltage • All current, PWMS & Feedbacks are terminated at Front panel • FRC Connectors are provided to Interface with the Embedded/DSP controllers • All the Input/output Lines are terminated at Banana sockets.
Kaplan Turbine Test Setup
DESCRIPTION:
Kaplan Turbine is an axial flow reaction Turbine named in honor of Dr. B. Kaplan, a Gennan Engineer. This turbine is suitable for low head. The power produced by a turbine is proportional to QH. As the head (H) decreases the J discharge (Q) must increase to produce the same power. The present Set-up consists of a scroll casing housing a runner. Water enters the turbine through the stationary guide vanes and passes through the runner axially. The runner has a hub and airfoil vanes, which are mounted on it. The water is fed to the turbine by means of Centrifugal Pump. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. A transparent hollow cylinder made of acrylic is fitted in between the draught tube and the casing for observation of flow on to the airfoil vanes. This runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of this brake arrangement so that the efficiency of the turbine can be calculated. The Set-up is supplied with control panel. A draught tube is fitted on the Outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and Vacuum Gauge are fitted at the Inlet & Outlet of the turbine to measure the total supply head on the turbine.EXPERIMENT:
1.To study the operation of a Kaplan Turbine 2.To determine the Output Power of Kaplan Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 109 (1.33 HP) | HM 109 (5 HP) | |
| Output Power | 1.33 HP / 1 Kw | 5 HP / 3.75 Kw | |
| Discharge | 1500 LPM (Approx.) | 5000 LPM (Approx.) | |
| Supply Head | 5 m | 5 m | |
| Rope Brake Dynamometer | Dia 200 mm | Dia 300 mm | |
| Sump Tank | Capacity 300 Ltrs. | Capacity 600 Ltrs. | |
| Water Circulation Centrifugal Pump | Capacity 7 HP, Three Phase | Capacity 20 HP, Three Phase | |
| Speed | 1500 RPM (approx.) | ||
| Runner | With adjustable Curved Vanes | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
Electronic Digital Theodolite
Description
This cost-effective Electronic Digital Theodolite provides excellent performance, reliable quality and practical operation for any construction application. The body style is similar to a Topcon Digital Theodolite and is combined with easy to use operation. The smart appearance and reasonable structure is as attractive as its price. • Tribrach. • AA Rechargeable Batteries (4 each). • Lens Cap. • Operator's Manual. • Hard carrying case.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Reagent Reservoirs
The Universal Reagent Reservoir is a graduated single reagent reservoir with maximum volume of 50 ml, reservoir with 8 separate numbered 5ml.
Reagent channels & a reservoir with 12 separate numbered 5ml. Reagent channels.
Made of polypropylene these reagent reservoirs are repeatedly autoclavable and can be used with all multi-channel pipettes.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Reagent Reservoir 75 ml | 12 |
Front Axel Assembly With Differential Gear
Front Axel Assembly With Differential Gear (Actual Cut Section)
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Mammal
Breast Examination Model
Description
Demonstrate realistic self-examination with our natural casting of a female upper body with medium sized breasts. It can easily be worn, in order to better train and practice breast self-examination. Made of high-quality silicone. Displays the skin in finest detail. Very realistic to the touch and dermatologic ally tested Breast examination is possible in both upright and lying positions.Benign and malignant tumors in different stages of development hone self-examination skills:
2 benign tumors 4 malignant tumors 2 typical anomalies Includes “Female Breast” chart Supplied with talcum powder, harness, stand and aluminum carrying case.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Amplitude Modulation And Demodulation
Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission. It is still used in radio system to transmit audio signal although it has lesser in popularity compared to FM (Frequency Modulation) due to its lower signal to noise ratio.
Technical Specification :-
1. I C based DC regulated Power Supply ±12 V / 500 mA.
2. Audio frequency 1 KHz / 0-2 Vpp for modulating signal 455 KHz / 2.5 Vpp approx. for Carrier Frequency.
Logic Gates Trainer
Logic Gates Trainer has been designed to study logic gates and applications. This trainer board is designed to verify the truth table of various logic functions, to prove De-Morgan’s theorem, Half adder and Full adder by using logic gates. The board is absolutely self-contained and requires no additional apparatus. 12 V / 1 A DC adaptor is required to operate it.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
REDWOOD VISCOMETER
PRODUCT DESCRIPTION
Oil & Petroleum Testing Instruments is widely acknowledged for its high functional efficiency, excellent results, accuracy, robustness, ability to withstand extreme working conditions and low maintenance requirements. Technically advanced and durable, these instruments are offered at industry leading prices in different specifications as per the requirements of the clients.
Demonstration Gear Model System
Description
A series of models to demonstrate different gearing systems. With transparent slideplates, the gears may easily be seen and where necessary there is an index on the primary and secondary shafts to show the change in the direction of rotation and the relative speed of rotation. A simple three-speed and reverse-gear system using spur gears. Reverse gear is obtained by interposing a small lay-shaft mounted pinion between the two main shafts. Gear selection is by means of a short ball-ended lever.
CAVITY BLOCK
Tablet Coating Pan
Product Description
We offer coating pan that is designed to perfection and fabricated from best grades of raw material procured from reliable sources. These coating pan are suitable for coating tablets and is checked by our quality controllers for high performance and uniform coating all over the tablet. The different parts of our coating pan machines are listed as under:PAN
The coating pan is SS semi ellipsoidal size pan with a circular mouth for charging & discharging of tablets, Pan mounted at an inclination of 45 degrees to the horizontal.DRIVE ASSEMBLYPAN
The tablet coating pan consists of a suitable HP 3 Phase, 440 V, 1440 RPM TEFC motor with suitable worm reduction gear box and cone pulley arrangement to give three speed output.HOT AIR BLOWERPAN
The tablet coating pan unit is provided with a hot air blower consisting of suitable HP 3 Phase 440 V, 2880 RPM TEFC electric motor & centrifugal blower with damper delivering required CFM. The air is heated by means of suitable electric heater to give air at 30 to 90 degrees Heater with thermostat control and flexible hose pipe.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Demonstraton Electric Bell
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Orbital Shaking Incubator
Specification
Outer made of M.S. Sheet powder coated & inner chamber is made of thick S.S. Sheet. The gap between two walls is fitted with high grade glass wool. The glass window makes it possible to inspect specimen without disturbing inner Temperature. The unit has a temprature range from ambient to 60°. Temperature is controlled by Dual Display Microprocessor PID Digital Temperature Indicator Cum Controller with a accuracy of + 0.5°C. Air Circulation Fan is provided to maintain stability throughout. Speed of shaker is variable from 30 RPM to 250 RPM. The tray of the shaker is also made of S.S. Sheet with Lotus type clamps to hold flasks. Unit is fitted with Digital RPM Meter, 999 min digital time.Optional Accessories
Timer 0-24 Hours. 16 Flasks of 100ml. instead of 9 flasks of 250ml. 9 Flasks of 500ml or 25 flasks of 100ml instead of 16 flasks of 250ml. 25 Flasks of 250ml or 36 flasks of 100ml instead of 16 flasks of 500ml.Size
9 Flasks of 250ml. 16 Flasks of 250ml. 16 Flasks of 500ml.
Atomic Model Set
We present to you, Atomic Model Set.
The Atomic Model Set consists of moulded balls of different colors & sizes along with connectors of different sizes.
The sizes & shapes of the balls & connecting lugs have been designed in accordance with internationally acceptable standards.
Material : Polystyrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Atomic Model Set - Senior Set | 1 | |
| Atomic Model Set - Junior Set | 1 | |
| Atomic Model Set (Euro Design) - Student Set | 1 | |
| Atomic Model Set (Euro Design) - Teacher Set | 1 |
