XTEMOS ELEMENT
AJAX PRODUCTS TABS
Pulley Blocks
8085 Microprocessor Trainer Kit
Specification
• Intel 8085A CPU @ 6.144 MHz Clock speed. • RAM : 8KB expandable upto 32KB, Jumper selectable. • EPROM : 8KB expandable upto 32KB, Jumper selectable. • Lithium Battery backup for RAM. • 21 Keys multi-function keyboard with double shot characters for long life. • 6 digit 7Segment RED LED Display. • 3 Channel 16 bit counter / timer terminated in a 10 Pin Connector. • 48 TTL I/O Lines, terminated at 26 pin FRC connector • RS232C Compatible serial Port terminated in a 9 Pin "D" Male Connector. • One VXT Bus (50 Pin FRC Connector) for interfacing VBMB series of Experiment boards and bus expansion. • Built-in SMPS Power Supply: Input : 230V AC, Output: +5V / 3.5A, +12V / 150mA. • Built in Line Assembler and Disassembler provided. • Software single stepping of user programs by instruction for software debugging. • This trainer helps to learn the characteristics of double acting cylinder namely direction, speed & force. • A Microcontroller ADC relay driver provided to actuate the cylinder. • Gear pump supplies the hydraulic fluid to double acting cylinder through direction control valve. • Pressure control valve controls the flow rate of fluid to cylinder. • Single phase induction motor drives the pump. • Control unit communicate with PC and controls the double acting cylinder using LabVIEWSoftwares. • Two proximity sensors are provided to indicate the position of the cylinder. • Load cell measures the force developed by the cylinder. • 5/2 Double Solenoid Valve directs the cylinder. • One tank is used to store the hydraulic fluid.
Beaker (TPX)
The company is primarily engaged in the exporting and trading of the latest Beaker (TPX) all across the globe.
The demand for our Beaker (TPX) has gradually increased over the time span, for their various attributes, and premium quality.
Our Beaker (TPX) are available in different specification and at affordable prices.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Gear Box Actual Cut Section
Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
Hope’s Apparatus
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Steering Geometry Wheel Alignment Trainer
Steering Geometry & Wheel Alignment Trainer
With the help of this trainer the students can learn about steering geometry and practically perform wheel alignment using various tools.
(A) Turn Tables
(B) Toe In Toe Out Gauge
(C) Magnatic Caster Camber Gauge
(D) Manual Steering System With Four Wheels
(E) Tool Kit
Tray Dryer
| Design | Standard, Customized | |
| Capacity | 96 trays | |
| Automatic Grade | Automatic, Semi-Automatic | |
| Max Temperature | 250 degree C |
| Chamber Size (HxWxD) | Tray Capacity mm Inches | |
|---|---|---|
| 430x840x650 8Tray | 16”x32”x 1 1/4 | |
| 430x840x910 12Tray | 16”x32”x 1 1/4 | |
| 910x840x910 24Tray | 16”x32”x 1 1/4 | |
| 960x1270x1450 45Tray | 16”x32”x 1 1/4 | |
| 960x1700x1700 96Tray | 16”x32”x 1 1/4 |
Optional
Timer 0-24 hours. Digital temp. Indicator-cum-controller. Tray 16”x32”x 1 1/4 size.
Turbine/Pump Unit
Description
For use as a water turbine to drive a generator producing electricity or for use as a pump driven by a motor and raising a head of water to produce potential energy. The rotor has eight 'bucket' blades and is housed in a block turbine chamber with a clear Perspex front. Two inlet tubules (for turbine and pump operation respectively) and one outlet tubule are provided and the shaft carries a 15 mm. diameter pulley. With driving belt.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Lubrication System Of An Automobile
In this model the working of lubrication system of a car is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a lubrication system of a car are shown in actual working form. This model helps the student to understand the working of the lubrication system of a car very easily. It is specially made dissectible for demonstration purposes.
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Gynecological Examination Model
Description
Gynecological Simulator is ideal for all aspects of gynecological education, training and competency evaluation, including the bimanual exam, speculum exam, and cytology sampling. Students will appreciate the unprecedented realism of its internal and external features, while instructors will love the interchangeable components that make up its unique modular system. This simulator allows you the flexibility of customizing your scenarios with use of included makeup, blood, and thickener. Additional specialized modules are also available (STD, post-menopause, S.A.N.E., and pre-puberty). Starter unit includes torso, normal genital pad, normal pelvic organ block with vagina and rectum, abdominal gel pad, fabric abdominal pad, abdominal overlay skin, seven uterus/cervix pieces (normal/normal with discharge option, retroverted/cervicitis, cancer/cancer, transparent IUD trainer, post-menopause/herpes, fibroids/polyp, early pregnancy), five detachable ovaries (normal, polycystic, small cyst, large adnexal mass), bladder insert, pelvic organ prolapse insert, baby powder, Injury Shades Makeup Wheel, Primary Colors Makeup Wheel blood mix, hydroxyethyl cellulose thickener, syringe, lubricant, instruction manual, and hard carry case.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Flexible AC Transmission Systems
Three phase FACTS help the students to get insight of FACTS operation in Realtime by enhancing their understandings through various experiments. This module can be used to analyze the effect of shunt compensation (STATCOM- STATIC Compensator) series Compensation (SSSC - Static Synchronous Series Compensator) and Series - Shunt Compensation (UPFC - Unified Power Flow Controller) in the transmission line.
It consists of
• Generator Set-up (3Φ AC Source) • Simulated Transmission line • IGBT Based VSI Power Module • Series & Shunt Transformers with LC filter • RLC - Load setup • TMS320F2812 DSP Controller • Upgrade possibleGenerator Set-up (3Φ AC Source)
• 3 phase Alternator DC Motor Drive setup 3Φ / 1KVA / 1500 RPM / Salient Pole type coupled with 2HP/220V DC shunt motor and with suitable drive from 1Φ AC input supply with • suitable speed control, sensor and digital speed indicator. • Digital controller with IGBT based DC voltage controller for DC motor Armature Voltage variation 0-200V DC/10A & Alternator field voltage variation with necessary instruments • /meters/indicators.
Muscle Figure
Histology (Shark)
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Pelton Wheel Turbine Test Setup
DESCRIPTION:
Pelton Wheel Turbine is only impulse water turbine now in common use named in honor of Sir L.A. Pelton (1829-1908) of California, USA. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the Inlet of the Turbine is only kinetic energy. The Pressure at the Inlet and Outlet of the atmospheric. This turbine is used for high heads. The Present Set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through SS nozzle with a SS spear, by means of Centrifugal Pump, tangentially to the runner. Row of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel the runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is providing with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid MS structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure Gauge is fitted at the Inlet of the turbine to measure the total supply head to the turbine.EXPERIMENT:
1.To study the operation of a Pelton Wheel Turbine 2.To determine the Output Power of Pelton Wheel Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 111 (1.33 HP) | HM 111 (2 HP) | HM 111 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1.5 Kw | 5 HP / 3.75 Kw |
| Discharge | 300 LPM (Approx.) | 400 LPM (Approx.) | 630 LPM (Approx.) |
| Supply Head | 25 m | 40 m | 45 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 150 Liters. | Capacity 200 Liters. | Capacity 300 Liters. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 7.5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1000 RPM (approx.) | ||
| Impeller | Material Brass, Bucket type | ||
| Nozzle | Material Stainless Steel/Mild Steel | ||
| Spear | Material Stainless Steel/Mild Steel | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
Rotary Air Compressor Test Rig
The Apparatus consists of a rotary vane compressor driven by an electric motor; Air intake is measured by an orifice meter and manometer, Discharge “pressure is measured by a pressure gauge. Power input of the compressor measured by an Energymeter. Thus the students can determine volumetric efficiency, power consumption and free air discharge of compressor.
SPECIFICATIONS:
1.Vane compressor – Rotary compressor, driven by 3 HP motor. 2.Calibrated orifice meter with water manometer to measure air intake. 3.Energy meter to measure input of the meter. 4.Pressure gauge to measure discharge pressure. 5.Control valve at delivery side. 6.Stop clock. 7.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Floor space of approx. 1.5 X 1.5 m. X 1.5 M. height. 2.440V, 16A, 3ph. supply. 3.Tachometer.
Profile Projector 300mm Dia
Specifications
300mm dia 360 degree rotatable graduated screen with venire and 90 degree cross hair line providing high accuracy of linear and angular measurements, providing illumination of contour lamp 12V/100W and two surface (12v/35W) lamps, with three standard magnifications.
Standard Features:
| X-Y Bed Size | : | 150mm X 150mm, fitted with hard steel balls for X-Y movement | |
| Travel X-Y movement (Standard) | : | 50 X 50mm | |
| Micrometers (50mm Dia) | : | Zero Adjustable 25mm (L.C 0.01mm) | |
| Angular Measurement | : | Manual, 360 degree graduated ring with 1 minute venire | |
| Maximum size of object view | : | 28mm (dia) | |
| Max Working Distance | : | 65 mm | |
| Standard Magnifications | : | 10x, 20x & 50x |
Sonometer 3-Wire
Description :-
Hollow wooden sounding box 1290 x 130 x 110 mm, with mm scale, has two fixed bridges 72 cm apart over which wires are stretched.
To one wire is fitted a spring balance reading to 100 N x 5 N and its tension can be adjusted by a winged nut and measured.
Another wire passes over a pulley and can be loaded as desired.
A third wire, for comparison, can have its tension adjusted by a wrest-pin.
With 3 movable bridges, wrest-pin key, spring balance, and set of four wires of different diameters, each 1.5 meter long, without masses.
Tilt Telescopic Collapsible Steering System
Tilt, Telescopic & Collapsible Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
