XTEMOS ELEMENT
AJAX PRODUCTS TABS
Solar System Model
Numerical System
This panel is used to demonstrate the number systems such as binary, decimal and hexadecimal numbers. Toggle switches used to activate the displays showing the particular number entered. Input may be entered either as decimal or binary numbers with a toggle switch for mode selection. Decimal numbers are shown on a three digit seven segment LED display. 12 V / 2 A DC adaptor is required to operate it.
francis turbine test setup
DESCRIPTION:
Francis Turbine is a reaction Turbine, which was developed by English born American Engineer Sir J.B. Francis. The water enters the turbine through the outer periphery of the runner in the radial direction and leaves the runner in axial direction and hence it is called a mixed flow turbine. As the water flows to the runner, a part of pressure energy goes on changing into kinetic energy. Thus the water through the runner is under pressure. The runner is completely enclosed in an air tight casing and the casing & runner is always full of water. The present Set-up consists of a runner. The water is fed to the turbine by Means of centrifugal Pump, radially to the runner. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is provided with a transparent. The circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the runner. The runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of brake arrangement so that the efficiency of the turbine can be calculated. A draught tube is fitted on the outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and vacuum Gauge are fitted at the Inlet and Outlet of the turbine to measure the total supply head on the turbine.UTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V Ac, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 101 (1.33 HP) | HM 101 (2 HP) | HM 101 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1 Kw | 5 HP / 3.75 Kw |
| Discharge | 1000 LPM (Approx.) | 1000 LPM (Approx.) | 2000 LPM (Approx.) |
| Supply Head | 10 m | 10 m | 15 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 300 Ltrs. | Capacity 300 Ltrs. | Capacity 600 Ltrs. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1500 RPM (approx.) | ||
| Runner | Having Curved Vanes | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Concentric Tube Heat Exchanger
(A)Plain Tube ( Water To Water ):
The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. While the outer tube consists of GI pipe through which cold water flows. The arrangement enables the parallel and counter flow of the cold water. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.
Specifications:
1.Inner copper tube I.D, 12.7mm. and outer G. I. Pipe I. D. 15mm. approx. and 1.5m. length. 2.Thermometers – 4 nos. 3.Measuring flask – 1 Lit. capacity. 4.Geyser-3 kW. Single phase.Services required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x I m x 1 m height. (B) Finned Tube ( Water To Air ): The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. It is finned at its outer diameter to increase the heat transfer surface. While the outer tube consists of GI pipe through which cold air flows. The arrangement enables the parallel and counter flow of the air. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.Specifications:
1.Inner copper tube I.D. 12.7mm. and outer G. I. Pipe I. D. 25mm. approx. and 1m. length. 2.Thermometers – 4 nos. 3.Orifice meter along with manometer. 4.Measuring flask – 1 Lit. Capacity. 5.Geyser-3 kW. Single phase.Services Required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x 1m x 1m height.
Newton’s Colour Disc, Motor Driven
Gas Turbines Or Turbojet Engine Model
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Basic Electro Pneumatic Trainer Kit
Features
• This trainer kit helps to design the circuits with logic sequence. • FRL unit receives air from compressor then filters, regulates & lubricates the air. • 5/2 direction control valve provided to control the double acting cylinder. • 3/2 direction control valve provided to control the single acting cylinder. • One way flow control valves provided to control the air flow. • Magnetic read switches are provided to indicate the position of the cylinder. • Control module controls the direction control valves using Switches, Relays and Timer.
Water Cooling Tower Apparatus
The apparatus consists of a forced draught, counter flow type-cooling tower. A blower supplies cooling air. Air enters the tower at the bottom. Hot water is, obtained from a geyser. Hot water is sprayed over the mesh packing through the nozzles and it flows downwards. Evaporative cooling of water occurs due to the current of air and water gets cooled. This student can study the operation of cooling tower and calculate the energy balance.
SPECIFICATION:
Cooling tower, fabricated of M.S. Sheets, 200 X 200 mm. cross section, 1.2m. height with Perspex front. Wire mesh packing is provided in the tower. Geyser – 3 Kw Capacity to provided hot water. Centrifugal blower, 1 HP capacity to force air through the tower. Multichannel Digital Temperature indicator to measure temperature at various points. Rotameter to measure inlet water flow. Measuring tank to measure outlet water flow. Calibrated orifice and water manometer to measure airflow. Arrangement to measure dry and wet bulb temperatures of air at 5 intermediate stations. A technical manual accompanies the unit. The unit Is provided with anticorrosion an attractive color powder coating.SERVICES REQUIRED:
440V, 32A, AC supply with neutral and earthing connection. Floor space of about 2m. X 1.5m. Water flow of 10 Ht./min. at constant head
Blood Bank Rrefrigerator
Features
Temp Range/Precision : 4 ±1°C, 0.1 °C Control System : Microprocessor control Display Alarm : Large screen LED display/ Audio and visual alarm for Height or low temperature; System failure; Door ajar; Power failure Refrigeration Type : Forced air refrigeration system Door : Three-ply transparent glass door with lock, Heating film preventing frosting, Stealing joint strip with magnetic force Casters : 4 casters Power Supply : 110/220V±10%, 50/60Hz Capacity : 120L Refrigerant : R134a, CFC-Free Material Internal : Stainless steel Material External : Cold-rolled steel with anti-bacteria powder coating Drawers/Shelves : Shelves Consumption : 160W External Size(L*W*H) : 520*600*1050mm Standard Accessory : Temperature printer, 2 shelves, 6 baskets, fluorescent lightSpecifications
Temperature- 2°C to 4°C Temperature Accuracy- + / - 1°C Temperature Controller- Digital P.I.D Controller Display- LCD / LED Display Alarm- Audio visual alarm for high and low temperature. Power Failure Alarm- Yes Refrigerant- Non-CFC Refrigerant Defrost type- Automatic Air Circulation- Forced air circulation External Construction- Stainless Steel 304 grades / MS Power Coated Interior Construction -Stainless steel 304 Insulation- CFC free high density polyurethane foam insulation Shelves- Adjustable and made of quality steel wire Illumination- Fluorescent Lamp Safety Device- High and low temperature protection Power Supply - 220 Volts
IPM Based Power Module
Power Module is designed for Motor control Applications upto 3 HP by using IGBT & DIODE Technology Based IPM. Input:1 Phase / 3 phase 50 Hz AC. Output : 400V/10A (MAX), AC/DC on each Leg of 3 phase Bridge
FEATURES:
• 1200V, 25A, 3 Phase IGBT Inverter Bridge • 1200V, 10A IGBT for Over Voltage breaking • Built - in Over Voltage, Under Voltage, Over Current & Over Temperature ProtectionADDITIONAL FEATURES:
• 1200V, 25A Converter Bridge for AC-DC power conversion • 4 Nos of Hall Effect current sensors are provided to sense the DC Link current & 3 output current of the Inverter Bridge • 1 No of Hall Effect Voltage sensor is provided to sense DC Link voltage • All the PWM signals are isolated using Opto Isolator • Protection circuit for over current with LED indication • Optically Isolated Fault signal from the IPM is given to the Embedded/DSP controllers for protection. • Independent Power supplies for all Isolated circuits. • 0-900V Voltmeter is provided to Indicate the DC Link Voltage • All current, PWMS & Feedbacks are terminated at Front panel • FRC Connectors are provided to Interface with the Embedded/DSP controllers • All the Input/output Lines are terminated at Banana sockets.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Wheatstone Bridge, Two Gap
Description
Comprising a resistance wire swg 24 stretched along a meter scale subdivided in mms and marked every cm. is clamped to stout brass plates so as to avoid end errors. A plated brass strip with 4 mm socket terminal is fitted along the meter rule to provide a two gap system for normal Wheatstone bridge work. Complete with jockey.
Physical Optics Kit
Description
Consists of: 1. Eight Plano-convex lens fl 500 mm, 1 Plano convex lens of fl 150 mm. 2. Twelve lens holders. 3. Four plates of different apertures, 32, 22, 11 and 5.5 mm diameter resp. 4.Three plates with small holes in circles of 29, 22, 10 mm diameter 5. One plate with circular aperture of 5.5 mm diameter 6. Four multi-aperture plates. 7. Four stop plates. 8. Two slide holders. 9. Six translucent screens. 10. Ten white cards. 11. Four Eye-pieces. 12. Fifteen each Red, Green and Blue filters. 13. Forty Black cards with holes. 14. Forty razor blades. 15. 120 Rubber bands. 16. One piece black chiffon for diffraction effects
Alage & Fungi
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Chlamydomonas , General structure & Life History Ulothrix general structure and L.H. Oedogonium Life Cycle Spirogyra structure & conjugation Chara structure & L.H. Nostoc structure & L.H. Ectocarpus structure & L.H. Dictyota structure & L.H. Fucus structure & L.H. Rhizopus structure & L.H. Mucor structure & L.H. Yeast Bacteria – I showing structure and forms Bacteria – II showing reproductive Virus types, structure & L.H. Penicillium Albugo(Cystopus) structure & reproduction Puccinia graminis structure & L.H. Agricus structure & life historyXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Lathe Tool Dynamometers
This is a strain gauge type two component lathe tool dynamometer designed to measure vertical and horizontal forces on the while orthogonal cutting process. The unit is in two parts one is mechanical sensing unit or tool holder, which can mounted on the top of the Ross slide after removing swivel base and compound slide of a lathe and digital force indicator. With this Dynamometer student can study the change in these forces by varying Speed, Cut and Feed.
FEATURES:
1.Rigid in construction 2.Sensitive transuding and amplifying system for accuracy in force measurement. 3.Compact Digital force indicator. 4.Use of cutting fluid during operation is possible.SCOPE OF SUPPLY:
1.Mechanical sensing unit or Tool Holder with string gauges. With H.S.S. tool of ½ “ size. 2.Control panel housing digital force indicator to measure two forces simuletensiously, balancing potentiometers, connoting cable. 3.Necessary switches, fuses and polycarbonate front plate. Range o to 500 Kg. 4.Centre Height, P.C.D.of clamping bolt size, clamping Bolt size. Three component lathe tool dynometer is also available.
Wireless Connectivity Kit
A Powerful Wireless Connectivity board is designed based on Sitara AM335X Cortex-A8 for detailed and combined study of different Wireless Communications. All in one Wireless Kit contains GSM/GPRS, GPS-GLONASS SBAS (GAGAN), ZIGBEE, RFID, Bluetooth and Wifi on board modules. It supports Linux, WinCE and Android OS Packages which can be used to study different applications like GPS tracking, wireless home and industrial security system, SMS and ZigBee based home application and lighting control and many more.
Features
• TI Sitara AM3354: - ARM Cortex-A8 32-Bit RISC Microprocessor NEON SIMD Co-processor - SGX530 Graphics Engine • DDR3 RAM : 4 GB • NAND Flash : 4 GB • 7” TFT Display Interface • Touch panel (Resistive and Capacitive) interface • On board WLAN (802.11 b/g/n), Bluetooth (802.15) • USB 2.0 – Host, OTG • Serial Interface : UART, SPI, I2C • On board - 10/100MPPS Ethernet PHY • Audio : - Digital Microphone - Multichannel Audio Serial Port (McASP) • Analog to Digital Converter
Soil Auger
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
VHDL/VERILOG Learning Kit
Features
• Based on 64 Macro cell Xilinx CPLD device : XC2C64A • 20 SPDT Slide switches • 16 output LEDs and One 7 segment LED display • 4x4 Matrix keys using Micro switches (4 multiplexed with 4Nos of Slide switch) • One NC/NO switch for giving manual clock • Square wave Oscillator • Onboard USB to JTAG and External JTAG Connector for programming the CPLD • 16 I/O Lines terminated at 20 pin connecter. • External 5 volt 2Amp power supply • Compatible with Xilinx ISE Design Suite Web Pack Software. • USB Cable • Onboard USB to JTAG is Compatible only with Vi JTAG 5.0 Software.
Corcyra Egg Laying Cage
Description
Frame made of MDF sheet planks. Fine wire mesh provided on top and bottom fitted with 3mm dia hole wire mesh on one top, a rounded opening 3cm dia is provided which can be closed with wooden plug. On one side a rounded opening 11cm with an arrangement for drop clouser with the help of MDF sheet cover is provided for manually putting in/taking out the material. Size 35x25x18cm
Utility Tray
We excel in providing high quality Utility Tray to our valuable clients.
Our range of Utility Tray is well appreciated in the market for its high quality and durability.
this Polypropylene Tray can be utilized for wide range of purposes ranging from drying glassware to sterilizing and for storing any laboratory apparatus.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Utility Tray 375 x 350 x 130 mm | 6 |
Micro Tip Box
The Micro Tip Box offered by us unique boxes are moulded in polypropylene and are therefore autoclavable.
The box itself is clear providing inside to hold the tips.
The tip holding spaces are uniformly placed to facilitate the use of multi channel pipettes.
The cover is joined to the base through ball catcher hinges and provides excellent protection to the tips.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Micro Tip Box For 96 Micro Tips of 2-10μl | 6 | |
| Micro Tip Box For 96 Micro Tips of 2-200μl | 6 | |
| Micro Tip Box For 96 Micro Tips of 200-1000μl | 6 |
