XTEMOS ELEMENT
AJAX PRODUCTS TABS
LPC 2148 Development Kit
ON Chip Features
• CPU - LPC2148. • Core - 16/32 Bit ARM7TDMI-S. • Speed - Max 60 MHZ. • Flash - 512KB. • RAM (on-chip) - 40KB. • 46 x General Purpose I/O Pins. • USB2.0 Full speed Compliant Device. • One 10bit ADC with 14 Analog inputs. • One 10bit D/A Converter. • Two 32bit Timers/ External Event Counters. • Low Power Real Time Clock. • Six PWM & Watchdog. • Two UARTS (16c550). • Two Fast I2C (400Kb/s) Module.On-Board Features
• Two Digital output. • Two Digital input. • 10 base T Ethernet Interface. • USB 2.0 Connectivity. • SD Card Interface. • 16 x 2 character LCD Interface. • 2 Analog Inputs are Terminated at Potentiometer. • RS232 lines are terminated at 9 pin D-type connector. • CPU lines are terminated at 20 pin connector.
Motor Generator Model Set
Description
This motor-generator set gives students an insight into the physical and technical relationships on which electric motors, generators and transformers are based. The modular system allows to set up different function models without tools: Various DC motors Series and shunt motor Synchronous motor DC generator and alternator Transformer. This set allows the performance of 10 student experiments about the following topics: Magnetic field of a coil Conversion of electrical energy into kinetic energy Commutator Direct current motor Synchronous motor Series and shunt-wound motors Electromagnetic induction The electrical generator Engine-generator Transformer
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Petri Dish Rack
We offer comprehensive range of Petri Dish Rack to our valuable clients.
These Petri Dish Racks are clear acrylic construction with polycarbonate posts.
Our range of Petri Dish Rack has a capacity to hold 60 petri dishes of 90 mm size while Petri Dish Rack can hold 56 petri dishes of 60 mm.
Useful during inoculation, incubation & storage, Petri Dish Rack enables the culture to be seen & checked during.
Material : Polymethyl Methacrylate / Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Rack For 90 mm Petri Dish | 2 | |
| Rack For 60 mm Petri Dish | 2 |
Dicot Stem Anatomy T. S. & L. S.
Description
This model shows the transverse and longitudinal section of a dicotyledonous stem in which case the cambium ring has been formed but no secondary growth has yet taken place. Useful model for study of epidermis, lentice , cork layer, cork cambium, cortical parenchyma ,starch sheath, medullary rays, phloem, sieve plate, sieve tube, phloem parenchyma and inter fasicular cambium ,xylem, pitted vessels, bordered pitted vessels, annular vessels, spiral vessels, pith etc. Mounted on base, with key card.
Anti Lock Braking System ABS Trainer
Anti Lock Braking System (ABS) Trainer
All modern car are now days fitted with anti lock braking system. This trainer helps the students to understand the working of ABS. The trainer consists of the following parts.
1. Control Panel,
2. Break Light,
3. ECU,
4. ABS Hydraulic Activator,
5. Break Lever,
6. Pressure Gauges,
7. Common Pressure Gauge.
An anti-lock braking system (ABS) is a safety system that prevents the wheels on a motor vehicle from locking up (or ceasing to rotate) while braking. A rotating road wheel allows the driver to maintain steering control under heavy braking by preventing a skid and allowing the wheel to continue interacting tractively with the road surface as directed by driver steering inputs. ABS offers improved vehicle control and decreases stopping distances on dry and especially slippery surfaces for many drivers, but on loose surfaces like gravel and snow-on-pavement it can slightly increase braking distance, while still improving vehicle control. Stopping a car in a hurry on a slippery road can be very challenging. Anti-lock braking systems (ABS) take a lot of the challenge out of this sometimes nerve-wracking event. In fact, on slippery surfaces, even professional drivers can’t stop as quickly without ABS as an average driver can with ABS.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Turbine/Pump Unit
Description
For use as a water turbine to drive a generator producing electricity or for use as a pump driven by a motor and raising a head of water to produce potential energy. The rotor has eight 'bucket' blades and is housed in a block turbine chamber with a clear Perspex front. Two inlet tubules (for turbine and pump operation respectively) and one outlet tubule are provided and the shaft carries a 15 mm. diameter pulley. With driving belt.
Jet Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Jet Pump. The Set-up consists of a Mono-Block Jet Pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum Gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
Ø To determine overall efficiency and pump efficiency of the Jet Pump Ø To plot Head vs. Discharge, Pump efficiency vs. DischargeFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
1.Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. 2.Water Supply: Tap water connection ½ “BSP, Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Mono – Block Jet Pump Test Rig Ø Pump & Drive : Mono – Block Jet Pump, Size 32 mm x 25 mm x 25 mm (Suction x Pressure x Delivery), Capacity 1 HP Ø Supply Tank : Capacity 70 Ltrs. Ø Measuring Tank : Capacity 50 Ltrs fitted with Piezometer Tube & Scale Ø Medium Flow : Clear Water Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Energy Measurement : Energy meter Electronics, L & T make Ø MCB : For Overload Protection Standard make On/Off Switch, Main Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Car Chassis All Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Solenoid
Photon Energy Array
Heat Transfer In Aagitated Vessel
The unit consists of a vessel with class wool insulation ail around. A helical coil made of copper is fixed inside the vessel. A motorized agitator is fixed at the center of the coil. The vessel is provided with an electric heater and a controller is also provided for vessel. Heater heats water in the jacket while cold water is circulated through coll. Temperature of circulated water and water In vessel Is measured and thus heat transfer coefficient at various agitator speeds can be determined.
SPECIFICATIONS:
1.Vessel approx. 20 lit. capacity, provided with glass wool insulation all around and electric heater at the bottom. 2.Agitator 150 mm dia, with 1/8 HP motor to drive the agitator. 3.Helical coil – 200 dia, 8 turns, made of 3/8″ dia. copper tube. 4.Controllers for heater and agitator motor. 5.Temp. Indicator for vessel water temperature and circulated water inlet and outlet.SERVICES REQUIRED:
1.Single phase 230V, 15 A stabilized supply. 2.Water flow at the rate of 4 to 5 lit. per min. 3.Suitable drain arrangement for water. 4.Floor area -1.5 mtr. X 1 mtr. X 1 mir height.
Analgesiometer Tail Flick
Analgesiometer Tail Flick (Radiant Heat or Tail Flick Type): It provides pain stimulus by heated nichrome wire in a Rat's tail to determine analgesic effect of drugs.
Complete with one spare element to work on 220 A.C.
Features
Shutter operated lamp illumination system. Automatic or manual mode for detecting tail flick. Precise and reproducible results. PC Connectivity with software. Software with calibration and report generation feature. Software with auto experiment number and serial number feature. Software with provision to convert data in excel or pdf. Cut off timer to avoid damage to animal. Calibration mode using Heat Flux meter (optional device).XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Resistor Set
Description
Consisting of six resisters of resistances with different current ratings. The resistors can be used in either the series or parallel mode. The resistors can be connected to any of the desired circuits through the safety sockets provided on the top of the kit for each resistor separately. Accuracy ± 5% . The specifications of each resistor are printed on the top panel of the kit. Mounted in moulded box.
Petri Dish
These Petri Dish offered by us is clear, unbreakable, & autoclavable.
The PS Petri Dish with fitting proves excellent for culture exp.
Made in polystyrene, this transparent Petri Dish provides an excellent inside view.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Petri Dish 50 mm | 36 | |
| Petri Dish 75 mm | 36 | |
| Petri Dish 100 mm | 36 | |
| Petri Dish 125 mm | 12 | |
| Petri Dish 150 mm | 12 | |
| Petri Dish (Culture) | 12 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Four Stroke Petrol Engine Model
Description
Represents internal structure and operating principles of an air cooled two-stroke engine. All parts in aluminium alloy. Ignition is shown by means of a miniature bulb. Carburetter and fuel supply also sectioned. Mounted on base with printed diagram showing working. Two-Stroke Petrol Engine Four-Stroke Petrol Engine are also available.
Window Air Conditioning Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Insect Display Showcase
Description
For display of insects in corridors, laboratory etc. MDF frame with MDf sheet bottom and glass top is nicely polished. Bottom lined with 8mm thick EVA sheet. Raised wall with holes for insecticide bottom to make box airtight & pest-proof. Fitted with clips, lool, handle, hanging hooks on ends and fluorescent tube inside. Size 90x60x11cm.
Generation Of Involute Gear Tooth Profile
This board illustrates the process of cutting of involutes Gear Teeth, by use of rack type cutter It consists of 3 white acrylic discs A, B, C. having pitch circle diameter 450 mm, 300 mm & 200 mm respectively. A gear tooth profile with module 25mm can be traced out on a peace of paper placed between disc and cutter. An affect of Interference and Undercutting on correct profile of gear tooth can be studied from the profiles traced.
