XTEMOS ELEMENT
AJAX PRODUCTS TABS
Automatic Gear Box Actual Cut Section
Automatic Gear Box – Actual Cut Section
The working of automatic gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of automatic gear box are shown in actual working form. This model helps the student to understand the working of the automatic gear box very easily. It is specially made dissectible for demonstration purposes.
Orfice Mouthpieces Apparatus
DESCRIPTION:
An orifice is an opening made in the side or bottom of tank, having a closed perimeter, through which the fluid may be discharged. A mouthpiece is short tube fitted to a same size circular opening provided in a tank so that fluid may be discharged through it. Orifice and mouthpiece are used to measure the rate of flow of liquid. The apparatus is designed to measure the co-efficient of discharge of orifice & mouthpiece. The apparatus consists of a supply tank, at the side of which a universal fixture for mounting orifice or mouthpiece is attached. A centrifugal pump supplied the water to supply tank. Head over the orifice/mouthpiece is controlled by a by pass valve provided at pump discharge. A measuring tank is provided to measure the discharge. A gauge for measuring X and Y co-ordinates of jet from the orifice is provided, which is used to calculate Cv of orifice.SPECIFICATIONS:
[1] Supply Tank – 0.4 X 0.3 X 0.5m height [2] Orifice – 8mm and 10 mm. [3] Mouthpiece (a) LID = 4 (b) L/D = 1 (c) Bordas mouthpiece. (d) Convergent mouthpiece. [4] X-Y gauge for orifice jet co-ordinates. [5] Measuring tank of suitable capacity OR a calibrated water flow meter. [6] Sump tank of suitable capacity. [7] 0.5 HP pump with valve. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC. Power Supply.
Magnifier, Folding
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Expansion Model of Human Teeth
Motor Generator Model Set
Description
This motor-generator set gives students an insight into the physical and technical relationships on which electric motors, generators and transformers are based. The modular system allows to set up different function models without tools: Various DC motors Series and shunt motor Synchronous motor DC generator and alternator Transformer. This set allows the performance of 10 student experiments about the following topics: Magnetic field of a coil Conversion of electrical energy into kinetic energy Commutator Direct current motor Synchronous motor Series and shunt-wound motors Electromagnetic induction The electrical generator Engine-generator Transformer
Ice Melting Kit
Description
Demonstrates the difference in thermal conductivity of two different materials. The kit consists of two identical blocks, one made of aluminum and other made of plastic. When an ice cube is placed on aluminum it turns into water in seconds, while on plastic block it melts slowly. The aluminum block has a larger heat capacity and a higher thermal conductivity while the plastic block has lower values of both parameters. With instructions.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Newton’s Rings Apparatus
Clinometer Compass
Description
Clinometer Handle Compass is a reproduction of an antique Clinometer compass. The Handle Compass gets its name from its "handle" shaped sight, which actually serves two purposes With the compass level, an object can be viewed through the peep sights to determine its magnetic heading. The second and most interesting purpose is when tilting the compass on its side and viewing an object through the sights, its angle of elevation or declination can be found. A weighted pendulous arm beneath the compass needle can be read from one of three scales : Angle in degrees beneath the zenith (from straight up), angle in degrees of elevation or declination, and in inches per yard of slope. The compass has a needle lift mechanism to protect the compass jewel and the pendulous arm when being transported.
Gas Turbine/Turbojet Engine
Constant Volume Air Thermometer
Description
A metal stand fitted with 0-100 cm x 1 mm vertical wooden scale and supporting a mercury reservoir sliding on a metal rod. An air thermometer bulb fitted to a bracket can be attached to the other rod at either of two positions. With U-shaped base. Complete with 1 meter rubber tubing to connect reservoir to the bulb. Supplied without mercury.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Brush, Beaker
Bottle Cap Sealing Machine
Specifications
Bottle Cap Sealing Machine which is used by the industries for sealing the cap of the bottles. It is supplied with complete electric fittings accessories. Finds usage in pharmaceutical, chemical and food & beverage industries, the offered range is available in different specifications, in order to meet the variegated expectations of our valuable customer. Our provided Bottle Cap Sealing Machine is tested by the team of our professionals. Furthermore, our clients can avail the entire range from us at market leading prices. (a) Hand operated. (b) Electrical operated.
Model of Female Breast
PH METER
Product Description
Due to our wide expertise, we are involved in manufacturing and exporting Digital pH Meter. The leading technology we have incorporated in this equipment results in accurate measurement of pH balance. Widely demanded in pharmaceutical, chemical, and food and beverage industry, this digital pH meter is available at a competitive price for our prestigious clients. Features:- Sleek design
- Accurate results
- Digital display
- Digital PH METER
- Max Make
- E.I. Make
- PH Electrode (Glass) Routine
- PH Electrode (Gell Filled) Unbreakable
- Pen type PH METER
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Water Cooler Trainer
The apparatus consists of a storage water tank, embraced by evaporator coil of the cooling unit, cooling cycle comprises of a hermetically sealed compressor, air-cooled condenser, a capillary tube as expansion device and an evaporator cell. The stainless steel water tank is provided with insulation on air Sides and a door are provided at the top. Cold water can be taken out from a top provided and inlet water supply is controlled by a bail-operated top. Various measurements provided enable students to determine the theoretical and actual COP, power consumption, actual cooling capacity refrigerant flow and compressor volumetric efficiency of compressor.
SPECIFICATIONS:
Cooling Cycle a) Compressor Hermetically sealed type, having the capacity of 1/3 ton of refrigeration using R-12 refrigerant. b) Finned tube type air colled condenser with forced air flow. c) Filter cum drier for refrigerant. d) Capacity expansion device. e) Evaporator coil embraced on stainless steel water tank, Provided with glass wool Insulation. 2.Water drain tap and float operated inlet water tap are provided for water tank with insulated lift door at top. 3.Measurement a) Pressure gauges for evaporating and condensing pressure. b) Thermometers to measure refrigerant temperatures at inlet and out let of condenser and evaporator. c) Dial type thermometer for water temperature. d) Rotameter to measure liquid refrigerant flow. e) Energymeter to measure compressor Input. 4.Safely & Controls – a) Thermostat to put off compressor at set water temperature. b) Pressostat to put off compressor if high or low pressure Goes out of set limit. c) Over load protector for compressor, A technical manual will be supplied along – with the unit. Also, the unit is provided with an attractive and anti corrosion powder costing.SERVICES REQUIRED:
1.Floor space of 1.5 m. X 1.5 m. 2.Water supply of 5 lit/min, 3.230 V, 15A AC stabilized supply with earthing connection
Tablet Hardness Tester (Pfizer Type)
Product Description
A handy, tough and direct dial reading type tablet hardness tester, working as pair of plairs, generates breaking force in single grip. The instrument offers accurate and reproducible results much faster other conventional hardness testers.Specifications
Accuracy : ±0.2 Kg Least Count: 0.2 Kg Safe Testing Force: 20 Kg Maximum Tablet Diameter: 25mm
Displacement Vessel,Alluminum
Linear Air Track
Angular section aluminium alloy track, length 255cms, with staggered air holes, supported on two light alloy castings positioned 45 cm from each end of the track.
One support has a two- point contact and other one-point contact for lateral and horizontal adjustments for which a knurled screw is provided.
Large catapult arms with slots for elastic bands are fitted to each end of the track.
A fully fitted to one end of the track enables experiments involving acceleration under a constant force.
Identical end caps enable air to be introduced from either end of the track, bung being supplied to close the end not being used.
The vehicle buffer attachments and clamping screws are matt black to help interpretation of stroboscopic photographs.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Draining Rack
Draining Rack provides an excellent option for post wash draining of tubes & bottles in the laboratory.
The back plate of this Draining Rack has 20 holes into which pegs are tightened with the help of screw-nuts.
Bottom of the rack is provided with a tray which collects all the waste water drained down which can further be collected in a container via drain tube.
This rack not rot, stain or rust.
Material : Acrylopitrile Butadiene Styrene / Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Draining Rack | 1 |
Stefan Boltzmans Apparatus
The Stefan Boltzmann constant is an important constant in heat transfer. The apparatus determines Stefan Boltzmann constant. The apparatus consists of a hemisphere surrounded by hot water. Hot water is obtained from a water-heating tank. When the blackened disc is inserted at the center of hemisphere, heat is transferred into the disc from hemisphere by radiation and its temperature begins to rise, and from temperature raise rate. (It is measured at the intervals of 5 sec.) Stefan Boltzmann constant is determined.
SPECIFICATIONS:
Water heating tank provided with electric immersion heater. Hemisphere made of copper sheet, 200mm. dia. Surrounded water jacket of 250mm. Dia. Test disc made of copper 20mm. dia. provided with thermocouple at the center. Multichannel digital temperature indicator 0-200 C with 0.1C least counts to measure the temperature of hemisphere and disc. Audible buzzer with timer to ring at every 5 seconds. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Bench area of about 1m. x 05m. at working height. 2.230v, 15A, AC, electric supply with earthing connection
Hydraulic Bench Apparatus
OBJECTIVE:
To conduct the experiment of hydraulic bench, with separate experiential set ups i.e. Hydrostatic Pressure, Flow over Weirs, Bernoulli’s Theorem, Flow meter Demonstration, Impact of jet and Orifice Discharge etc. which are accessories of the Hydraulic Bench.DESCRIPTION OF APPARATUS:
The set up is a self-contained, water recirculation unit provided with a top tray, sump tank and a measuring tank. Drain valve and over-flow are provided on the sump tank. A centrifugal pump is fitted for water circulation. Flow control valve and bypass valve is fitted in water line to conduct the experiment at different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. Measuring tank is provided to measure the discharge. Drain valve is provided in the measuring tank to empty water in sump tank after measuring discharge. Separate level indicator and scale is provided to read the level of water in the measuring tank.UTILITIES REQUIRED:
1.Water Supply (Fill approx 250 Ltrs Initially). 2.Drain Required. 3.220 V AC, 50 Hz, single phase electric supply source. 4.Floor area 1.75 m x 1.50 m.SPECFICATION:
1. Top Tray : 1060 mm x 650 mm. 2.Pump : 1 HP 3.Flow Measurement : Using measuring Tank (Material SS) 4.Tank : Capacity 40 Ltr. 5.Sump Tank : Capacity 120 Ltr. Material SS. The whole set-up is well designed and arranged in a good quality powder coating painted structure.
Utility Tray
We excel in providing high quality Utility Tray to our valuable clients.
Our range of Utility Tray is well appreciated in the market for its high quality and durability.
this Polypropylene Tray can be utilized for wide range of purposes ranging from drying glassware to sterilizing and for storing any laboratory apparatus.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Utility Tray 375 x 350 x 130 mm | 6 |
