XTEMOS ELEMENT
AJAX PRODUCTS TABS
Masses Iron
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Unit Cubes
Interlinking Cubes are one of the most widely-used math manipulative in the world. The colorful, interlocking cubes help children to learn number and math concepts. These cubes represent units and link in all direction. Interlinking cubes are used for patterning, grouping, sorting, counting, numbers, addition, subtraction, multiplication, division and measurement. Each unit is a cubic centimeter measuring 1 cm x 1 cm x 1 cm
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Digital Trainer Using NAND Gates
Complete with Regulated power supply of + 5V/500 mA. Provided with 4 Logic input switches (bounceless) 4 LED Indicators (Buffered)
Functional diagram of :-
1. 3 Input NAND 6 No.
2. 4 Input NAND 4 No.
3. 1 Input NOT Gates 4 No. is printed on board.
4. 12 Interconnection Leads and User’s Manual is provided.
Comparative Study
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Vertebrate Hearts Vertebrate Brains Vertebrate Skulls Vertebrate Limbs Vertebrate Girdles Vertebrate Urino genital system Vertebrate Embryos Vertebrate Arterial arches circulation Vertebrate Genital apparatus & venous systemXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Vacuum Assisted Hydraulic Drum Brake
Vacuum Assisted Hydraulic Drum Brake With Vacuum Booster & Motorised Vacuum Pump
Suitably sectionised full size unit. Consisting of original parts such as :- vacuum booster with master cylinder assembly, wheel cylinder, brake shoes, brake drums, motorised vacuum pump and necessary connections. Completed with operating lever and mounted on heavy iron stand.
Discharge Over Notches Apparatus
DESCRIPTION:-
The Lab setup consists of a channel having sufficient length and width in which water is supplied from the bottom. Required Notch is fitted at one end of this channel .A hook gauge with Vernier scale is fitted to measure the height of fluid in flow channel. Arrangement for fixing interchangeable notches is made. Set of three brass notches, i.e. rectangular notch. 60 V notch & 45 V notch provided along with the set up. Present set – up is self –contained water re- circulating unit .provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass value are fitted in water line to conduct the experiment on different flow rate .Flow rate of water is measured with the help of measuring tank and stopwatch.EXPERIMENTS:-
Ø To Determination Co-efficient of discharge (Cd) through Ø V notch (45 deg. and 60 deg.) Ø Rectangular Notch. Ø Trapezoidal NotchUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity 0.5kw,220V AC, Single PhaseTECHNICAL SPECIFICATION: –
Ø Channel Test Section : Size 600x250x180 mm Ø Notches : Material Brass(3 Nos) 1. Rectangular Notch 2. 45 deg. V Notch 3. 60 deg. V Notch 4. Trapezoidal Notch Ø Hook / Pointer : With Vernier Scale Ø Water Circulation : FHP Pump, Crompton/Sharp make. Ø Flow Measurement : Using Measuring Tank with Piezometer, Cap.25 Ltrs. Ø Sump Tank : Capacity 70 Liters. Ø Stop Watch : Electronic Ø Control Panel : On/Off Switches, Main Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Concave Mirror, Spherical
4 Stroke 1 Cylinder Diesel Engine Motor Driven
The engine will be sectioned to show the internal constructional details. The working of individual part and accessories like Valves, Pistons, pumps, Crank and Camshaft, etc. will be demonstrated. It is provided with Flywheel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes. The actual cut section engine will be supplied with key card & very interesting literature regarding working.
Induction Coil
Description
This box form Induction Coil has a 50 mm spark gap and can produce pulses of high voltage spark from a low voltage direct current source such as a battery. It is suitable for use with gas-filled discharge tubes, vacuum tubes, eudiometers and for general laboratory work. It is comprised of two coils fully enclosed in a polished wooden case with binding posts. Spark gap at the discharge points can be adjusted by sliding rods back and forth
Vacuum Pump
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Model of Galilean Telescope
Autoclave, Radial Locking
Specification
Double wall chamber Autoclave. The inner chamber and outer wall made of stainless steel, ring made of stainless steel/ mild steel. The lid is made of stainless steel tightened by radial arms through a steering wheel made of chrome plated mild steel. The instrument is absolutely leak proof. Equipped with pressure gauze, safety valve, double safety valve, steam release valve, rubber gasket, inner container, S.S bucket and mild steel legs for Autoclave. The Autoclave can hold the in between 5psi to 20 psi. Autoclave, Vertical, Double Walled, Radial Locking.| Capacity (Lt.) | Size | |
|---|---|---|
| 23 litres | (10” x 18”) | |
| 40 litres | (12” x 22”) | |
| 52 litres | (14” x 22”) | |
| 60 litres | (14” x 25”) | |
| 75 litres | (16” x 24”) | |
| 95 litres | (18” x 24”) | |
| 180 litres | (22” x 30”) |
Conical Flask
Our superior quality Conical Flasks are made up of polypropylene, these cone shaped flasks are rigid, translucent & autoclavable.
The screw cap keeps the contents of the Conical Flasks contamination free and makes the flask leak proof.
The threads of the Conical Flasks should be disengaged before autoclaving.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Conical Flask 100 ml | 12 | |
| Conical Flask 250 ml | 12 | |
| Conical Flask 500 ml | 12 |
Conical Percolator
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
PH METER
Product Description
Due to our wide expertise, we are involved in manufacturing and exporting Digital pH Meter. The leading technology we have incorporated in this equipment results in accurate measurement of pH balance. Widely demanded in pharmaceutical, chemical, and food and beverage industry, this digital pH meter is available at a competitive price for our prestigious clients. Features:- Sleek design
- Accurate results
- Digital display
- Digital PH METER
- Max Make
- E.I. Make
- PH Electrode (Glass) Routine
- PH Electrode (Gell Filled) Unbreakable
- Pen type PH METER
PAM-PPM-PWM Modulation and Demodulation Trainer
PAM- PPM- PWM is the basic pulse modulation techniques. This trainer provides complete setup to the students for performing Experiments on these techniques. They can study Sampling, Pulse Modulation &Signal reconstruction process. Separate circuits are provided for each Techniques.
FEATURES:
• PAM- PPM- PWM Modulation and Demodulation Techniques,using Natural and Flat - top Sampling. • Natural Sample, Sample and Hold and Flat-top outputs. • Selectable 2 different sampling pulse frequencies on board. • On board Sine wave generators. • Voice communication using dynamic microphone and speaker • On board Filters and Amplifier • Functional blocks indicated on board schematic • Input- Output and Test points provided on board. • Built in DC Power Supply • Fully documented operating ManualTECHNICAL SPECIFICATION:
• Crystal Frequency : 6.14MHz • Sampling Frequency : 16 KHz, 32 KHz • Sine wave Generator : 1 KHz &500Hz, Amplitude (0-5)V, Tolerance +5% • Low Pass Filter : 4 Order BW Filter • Cut off frequency : 3.4 KHz • Voice Communication : Voice Link using dynamic mic& speaker • AC Amplifier : With Adjustable Gain control • Microphone type : Dynamic, 600 Ohm. • Audio Pre-amplifier : Op-amp based • Power amplifier : 1W Mono • Interconnections : BS2 Connector. • Power : 230V, 50Hz
Orfice Mouthpieces Apparatus
DESCRIPTION:
An orifice is an opening made in the side or bottom of tank, having a closed perimeter, through which the fluid may be discharged. A mouthpiece is short tube fitted to a same size circular opening provided in a tank so that fluid may be discharged through it. Orifice and mouthpiece are used to measure the rate of flow of liquid. The apparatus is designed to measure the co-efficient of discharge of orifice & mouthpiece. The apparatus consists of a supply tank, at the side of which a universal fixture for mounting orifice or mouthpiece is attached. A centrifugal pump supplied the water to supply tank. Head over the orifice/mouthpiece is controlled by a by pass valve provided at pump discharge. A measuring tank is provided to measure the discharge. A gauge for measuring X and Y co-ordinates of jet from the orifice is provided, which is used to calculate Cv of orifice.SPECIFICATIONS:
[1] Supply Tank – 0.4 X 0.3 X 0.5m height [2] Orifice – 8mm and 10 mm. [3] Mouthpiece (a) LID = 4 (b) L/D = 1 (c) Bordas mouthpiece. (d) Convergent mouthpiece. [4] X-Y gauge for orifice jet co-ordinates. [5] Measuring tank of suitable capacity OR a calibrated water flow meter. [6] Sump tank of suitable capacity. [7] 0.5 HP pump with valve. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC. Power Supply.
Outside Micrometers Engraved Marking
Description
Micrometer is used to measure short lengths accurately Technical Details : Engraved Marking On The Vernier Scale Carbide Tipped Measuring Faces Blue Metallic Finish Frame With Locking Clamp and ratchet stop ; Least Count : 0.01mm/0.001” ; Sizes ; 0-25 ; 25-50 ; 50-75 ; 75-100 ; Specifications Guarantee 6 Months without abuse Packing ; Plastic Box Calibration ; In house.
‘Gravity’ By Free Fall Apparatus
Consists of an electromagnet housed in a plastic moulded case with connections for an external timer, with a heavy steel sphere, and a platform unit.
For determination of 'g' (the gravitational acceleration) by free fall method.
The apparatus consists of an electromagnet which is housed in a plastic moulded case with 4 mm socket connections provided to energize the magnet and another pair of sockets for connection to a timer in use.
To perform the experiment, an electromagnet is energized and a metal sphere is attached.
As soon as the power to the electromagnet is switched off the sphere falls and the unit activates the timer.
When the sphere hits the platform, which is connected to a micro switch, the timer stops and the time of fall can be determined.
For use with compatible timer (product code LBTM).
Unit conveniently attaches to all commonly used stands (stand not supplied, see Stand & Rod Assembly - Value Pack STD-RD).
