XTEMOS ELEMENT
AJAX PRODUCTS TABS
Car Chassis All Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Three Hinged Arch Apparatus
The mild steel model has a span of 100cm and rise 25cm, with hinges at supports and crown. One of the ends should rests on rollers. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically determinate structure, the horizontal thrust developed under the action of any load system can be theoretically calculated and will also be measured directly by neutralizing the outward movement of the roller end. A dial gauge with 25mm travel (with magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Electronics Kit
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
N-P-N Transistor Unit
STAINING RACKS
Transformer Stand and Core
Description
Apparatus is designed primarily for demonstration of the basic principles of transformers. It consists of a laminated U-core with laminated I-core, both with 32 x 25 mm cross section to form a closed core of size 102 x 127 mm. Heavy aluminium alloy stand with removable clamping rods, 2 pole pieces, each 65 x 30 x 25 mm with one end cone shaped, to accept support rod and shading ring. Poles also have a hole drilled through lengthwise to take a light beam. 300 turns 600 turns 1200 turns 3600 turns 12000 turns
Gear Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Gear Pump. The Set-up consists of a Gear Pump having a pair of meshed gears coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum Gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
Ø To determine overall efficiency and pump efficiency of the Gear Pump Ø To plot Head vs. Discharge, Pump efficiency vs. DischargeFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Oil Supply: Oil @ 30 Ltrs. (Optional extra cost)TECHNICALS SPECIFICATIONS:
Ø Pump : Gear Pump with pair of meshed gears Capacity 1 HP,Speed 1500 RPM (max.), Head 5 Kg/cm2 (max.) Ø Drive : AC Motor with step cone pulley arrangement for 3 prefixed speed DC Motor with DC Drive along with (non-contact type Digital RPM Indicator Ø Supply Tank : Capacity 30 Ltrs. Ø Measuring Tank : Capacity 20 Ltrs. fitted with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Control Panel : With required electrical instrumentation (The whole Set-up is well designed and arranged in a good quality painted structure.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Linear Air Track
Angular section aluminium alloy track, length 255cms, with staggered air holes, supported on two light alloy castings positioned 45 cm from each end of the track.
One support has a two- point contact and other one-point contact for lateral and horizontal adjustments for which a knurled screw is provided.
Large catapult arms with slots for elastic bands are fitted to each end of the track.
A fully fitted to one end of the track enables experiments involving acceleration under a constant force.
Identical end caps enable air to be introduced from either end of the track, bung being supplied to close the end not being used.
The vehicle buffer attachments and clamping screws are matt black to help interpretation of stroboscopic photographs.
Electric Motor St. Louis
Description
The motor consists of a two pole armature mounted between the ends of two bar magnets. The armature has a two section commutator and a pair of slip-rings on its shaft and is so constructed that the wire cannot slip off the iron core. The upper bearing and brushes for the commutator are mounted on a strong upright. Separate brushes are provided for the commutator and for slip rings and each are connected to a terminal. The magnets are held in position by thumb screws.
Wide Mouth Reagent Bottle
Our Wide Mouth Reagent Bottle is available in Polypropylene.
The PP Wide Mouth Reagent Bottle, offered by us, are largely demanded for their unique features.
These features include Rigid, Translucent and have Excellent Contact Clarity.
Moreover, our Wide Mouth Reagent Bottle is available at affordable prices.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Reagent Bottle (Wide Mouth) 30 ml | 12 | |
| Reagent Bottle (Wide Mouth) 60 ml | 12 | |
| Reagent Bottle (Wide Mouth) 125 ml | 12 | |
| Reagent Bottle (Wide Mouth) 250 ml | 12 | |
| Reagent Bottle (Wide Mouth) 500 ml | 12 | |
| Reagent Bottle (Wide Mouth) 1000 ml | 6 | |
| Narrow Mouth Bottle 4000 ml | 1 | |
| Wide Mouth Square Bottle 4000 ml | 1 | |
| Heavy Duty Vaccum Bottle 2000 ml | 1 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Gat Tap, Superior
Description
Made of brass with superior black powder coating. Heavy construction having lever handle with locking arrangement to ensure lever rotation does not go beyond 90°. Output nozzle having 4mm bore. Inlet 3/8 X 26. Flange diameter 50mm with two holes to fix on bench or any other surface with screws. Provided with adapter (6/8, 3.8mm bore) and corresponding nut (8mm bore). Designed to operate at pressure up to 2 psi (0. 14kg/cm2). Suitable for use with coal gas, natural gas and L.P.G.Particulars
Gas Tap, One Way Gas Tap, Two Way Gas Tap, Three Way Gas Tap, Four Way
Genetics
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall, Size 75×100 cm. Monohybrid Crossing complete dominance Monohybrid Crossing incomplete dominance Dihybrid Crossing Monohybrid Crossing Mendelian explanation of Cross between tall & dwarf races in Garden Pea Sex linked inheritance Drosophila Mendelian Heridity of Blue & Adulsian fowls Mendelian Explanation of the breeding behaviour of Red & White flowering in 4 o’clock
Pipette Pump
fast release Pipette Pump for precise pipetting & zip quick emptying.
The Knurled thumb wheel can be rotated to draw up or dispense liquids while the releaser may be pushed in for zip-quick emptying.
The moulded chuck has silicon rubber coller inside to hold various pipettes of standard sizes.
The Pipette Pump resists acids & alkalis and can be easily disassembled for thorough cleaning.
Material : Acrylonitrile Butadiene Styrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pipette Pump 2 ml | 12 | |
| Pipette Pump 10 ml | 12 | |
| Pipette Pump 25 ml | 12 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Sonometer 3-Wire
Description :-
Hollow wooden sounding box 1290 x 130 x 110 mm, with mm scale, has two fixed bridges 72 cm apart over which wires are stretched.
To one wire is fitted a spring balance reading to 100 N x 5 N and its tension can be adjusted by a winged nut and measured.
Another wire passes over a pulley and can be loaded as desired.
A third wire, for comparison, can have its tension adjusted by a wrest-pin.
With 3 movable bridges, wrest-pin key, spring balance, and set of four wires of different diameters, each 1.5 meter long, without masses.
Spectrometer, Advanced
Description
Vernier reading to 30 seconds of arc. The 175 mm diameter scale is fixed. The table and telescope movements are completely independent of each other and read to 30 seconds of arc by means of double ended verniers and magnifiers. Both rotations have fine adjustment screws. Coarse adjustments can also be made by release of clamping screw. Collimator is mounted on a fixed pillar and is fitted with 175 mm fl. achromatic objective with 32 mm clear aperture and a laterally adjustable slit 6 mm long. Telescope is mounted on a movable pillar fitted with 175 mm fl. achromatic objective of 32 mm clear aperture and x 10 Ramsden eye-piece with a glass cross line graticule. Both the telescope and collimator have rack and pinion focusing and can be adjusted for leveling the axes of both units as well as for adjusting to the axis of rotation. Prism table is marked with lines to assist prism placement and has three table leveling screws. It also has an interchangeable clamping unit for the prism and diffraction grating. Complete with prism clamp, diffraction grating holder and a Tommy bar for adjusting optical axis, In case.
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Pneumatic Trough
We offer Pneumatic Trough to our esteemed clients.
The Pneumatic Troughs offered by us are made of polypropylene, autoclavable and are available in different sizes.
Moreover, the Pneumatic Troughs can be used for a wide range of applications including storage, sterilizing & drying lab ware etc.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pneumatic Trough Ø-180 mm x h-60 mm | 6 | |
| Pneumatic Trough Ø-200 mm x h-100 mm | 6 | |
| Pneumatic Trough Ø-250 mm x h-100 mm | 4 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Brunton Compass
Description
We offer Brunton Compass (Geological Compass) which is available in a leather or wooden case. This compass differs from modern compasses, as it utilizes magnetic induction damping rather than fluid to dampen needle oscillation. It is widely used by geologists and surveyors to make accurate degree and angle.
Linear Expansion Apparatus
Consisting of a metal rod, 500mm in length and 4.5mm diameter, enclosed in a well lagged, nickle plated brass tube with three tubules for steam, inlet, outlet and thermometer.
The metal rod to be studied is supported in the steam jacket by detachable conical cups situated at each end of the tube.
The apparatus is carried on a heavy gauge channel base at one end of which is an adjusting screw.
At the opposite end is a micrometer screw reading to 0.01mm for measuring the expansion.
Supplied complete with copper, brass & iron rods but without thermometer.
Concentric Tube Heat Exchanger
(A)Plain Tube ( Water To Water ):
The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. While the outer tube consists of GI pipe through which cold water flows. The arrangement enables the parallel and counter flow of the cold water. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.
Specifications:
1.Inner copper tube I.D, 12.7mm. and outer G. I. Pipe I. D. 15mm. approx. and 1.5m. length. 2.Thermometers – 4 nos. 3.Measuring flask – 1 Lit. capacity. 4.Geyser-3 kW. Single phase.Services required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x I m x 1 m height. (B) Finned Tube ( Water To Air ): The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. It is finned at its outer diameter to increase the heat transfer surface. While the outer tube consists of GI pipe through which cold air flows. The arrangement enables the parallel and counter flow of the air. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.Specifications:
1.Inner copper tube I.D. 12.7mm. and outer G. I. Pipe I. D. 25mm. approx. and 1m. length. 2.Thermometers – 4 nos. 3.Orifice meter along with manometer. 4.Measuring flask – 1 Lit. Capacity. 5.Geyser-3 kW. Single phase.Services Required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x 1m x 1m height.
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Condensers , Liebig, Drip Tip Interchangeable Inner & Outer Joint
| Socket | Cone | Effective Length mm | |
|---|---|---|---|
| 14/23 | 14/23 | 150 | |
| 19/26 | 19/26 | 200 | |
| 24/29 | 24/29 | 200 | |
| 19/26 | 19/26 | 300 | |
| 24/29 | 24/29 | 300 | |
| 19/26 | 19/26 | 350 | |
| 24/29 | 24/29 | 350 | |
| 19/26 | 19/26 | 400 | |
| 24/29 | 24/29 | 400 | |
| 24/29 | 24/29 | 500 | |
| 24/29 | 24/29 | 600 | |
| 24/29 | 24/29 | 750 | |
| 34/35 | 34/35 | 500 | |
| 34/35 | 34/35 | 600 | |
| 34/35 | 34/35 | 750 | |
| 34/35 | 34/35 | 900 | |
| - | 19/26 | 300 | |
| - | 24/29 | 350 | |
| - | 34/35 | 250 | |
| 29/32 | 29/32 | 250 | |
| 29/32 | 29/32 | 400 |
