XTEMOS ELEMENT
AJAX PRODUCTS TABS
Three Phase Cyclo Converter
This module is designed for three phase half wave-step down cycloconverter. It consists of 18 Synchronized firing pulses, 18 SCRs, Relevant power supply and circuitry for frequency divisions.
Specification
• Eightin nos. SCR with RC snubber protection is provided for 3phase • cycloconverter power circuit (each phase consist of 6 SCRs) Rated at 1200V@25Amps. • Three nos. center tapped inductor (0%.50%, 100%) is provided for power circuit. • Eightin nos. Isolated gate pulses for SCR power circuit. • One potentiometer is provided to vary the frequency. • One potentiometer is provided to vary the output voltage. • MCB protection. • Housed in sleek screen printer cabinet. • Provision for V/F control Power Supply. • Input 440V ± 10%, 50HZ three phase AC supply. • ± 15V DC, 9V, 9V, 9V AC (3phase) for the firing circuits. • 24-0-24V 3phase input for power circuit.
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Probe Type Anemometer Digital
Digital Stroboscope
Description :-
Stroboscopic flashes are triggered by either the internal oscillator or by external pulses which may be connected to the two 4mm sockets mounted on the rear panel of the instrument. Example of the many applications of this unit are to be found in motion analysis multi exposures photography, examination of moving parts and measurement of rotational speed.
Specifications:-
Input Volts : 220V AC, 50 Hz
Flash Rate: 0- 9999 Flashes per minute.
Resolution : 1
Display: 7 Segment LED (4 nos.)
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Bar & Gauge
Impact Of Jet On Vanes Apparatus
DESCRIPTION:-
The Set-up consists of two sided clear fabrication. Water is fed through a nozzle and discharged vertically to strike a target carried on a stem, which extends through the cover. A weight carrier is mounted on the upper end of the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured by adding the weights supplied to the weight pan until the mark on the weight pan corresponds with the level gauge. A total of two targets are provided a flat plat and a hemispherical cup.EXPERIMENTS:-
Ø To measure the force developed by a jet of water impinging upon a different targets (Hemispherical & Flat Plate) and comparison with the forces predicted by the momentum theory.UTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Test Plates : Material Brass (2 Nos.) 1. Flat Plate 2. Hemispherical Cup Ø Nozzle : Material Brass Ø Stainless Steel Chamber : Having of opposite sides made of glass Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 40 Ltrs. Ø Sump Tank : Capacity 60 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Ria Vial
These Polypropylene/Polystytene tubes are generally used in RIA , Coagulation & Bacteriology.
The Polypropylene tubes are clear and can withstand 3000 RCF during Centrifugation while the transparent Polystyrene tubes can withstand 1400 RCF.
The PP tubes can accept common acids, alkalis & solvents at room temperature while the PS tubes can accept mild bases, weak acids but not organic solvents.
Material : Polypropylene / Polystyrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| RIA Vail 12 x 75 mm / PS | 500 | |
| RIA Vail 12 x 75 mm / PP | 500 | |
| Cap For 12 mm RIA Tube | 100 |
Dental Care Model (28 Teeth), PVC
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Measuring Tape
Description
Measuring tape is a flexible form of ruler. It consists of a ribbon of cloth, plastic, fiber glass, or metal strip with linear-measurement markings. It is a common measuring tool. Its flexibility allows for a measure of great length to be easily carried in pocket or tool kit and permits one to measure around curves or corners.
Unit Cubes
Interlinking Cubes are one of the most widely-used math manipulative in the world. The colorful, interlocking cubes help children to learn number and math concepts. These cubes represent units and link in all direction. Interlinking cubes are used for patterning, grouping, sorting, counting, numbers, addition, subtraction, multiplication, division and measurement. Each unit is a cubic centimeter measuring 1 cm x 1 cm x 1 cm
Material Kit Solids
Economy Kit of 14 materials blocks.
This economy kit consist fourteen materials in the form of rectangular blocks, intended to familiarize the student with the appearance, 'feel', texture, hardness and density of a range of common substances.
Blocks, 50 x 40 x 30 mm. Wood, paraffin wax, aluminium, Iron, foamed polystyrene.
Blocks, 20 x 20 x 100 mm. Perspex, glass, slate, aluminium, softwood, Marble.
Blocks other sizes: Lead 50 x 50 x 20 mm
Brass 20 x 20 x 50 mm
Iron 40 x 40 x 20 mm
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Hydraulic Trainer Classic
Silent Features:
1. We are manufacturing cylinders for industrial applications. Our cylinders can withstand pressure up to 160 Bar. 2. Mobile and self-contained unit, only electrical connections are required. 3. Simplicity of operation and designed for amateur use. 4. Two pressure relief valves are provided in the system. One is provided inside the tank to increase the safety. 5. Hoses can withstand pressure of 188 Bar. 6. Test Pressure : 80 Bar ; Operating Pressure : 40 Bar. 7. Realistic Industrial circuits are demonstrated. 8. Special Bell housing is provided to maintain the Run out between Pump and Motor below 0.020mm. 9. Special fixtures used for pipe bending and ferrule fitting arrangement. 10. Specially designed front mounting plate. 11. System is flushed with very high velocity (4 times the working pressure) byseparate oil which maintains class A cleanliness of system. 12. Lowest pressure drop in the system to avoid overheating. 13. Cylinder are manufactured from precision honed tubes, hardened ground, hard chrome plated piston rods and imported quality seals.
DESICATOR WITH COVER
Product description:
Desiccator, Non-Vacuum, with Base, Lid and Perforated Porcelain Plate, Soda Lime Glass
Desiccators are sealable enclosures containing desiccants used for preserving moisture-sensitive items such as cobalt chloride paper for another use. A common use for desiccators is to protect chemicals which are hygroscopic or which react with water from humidity.
Size:
100mm
125mm
250mm
500mm
1000mm
Fungi
| Alternaria Host Leaf TS | Colletotrichum Acervulus |
| Cystopus Asexual VS | Cystopus sexual VS |
| Mucor Veg. WM | Mucor Sporangia WM |
| Mucor Sexual WM | Perenospora Asexual VS |
| Phyllactenia WM, VS | Rhizopus Veg. WM |
| Rhizopus Sporangia WM | Rhizopus Sexual WM |
| Synchytrium Host Leaf TS | Synchytrium Prosorus Aspergillus with Conidia WM |
| Erysiphae WM, VS | Morchella Fruiting Body TS |
| Penicillium WM | Yeast WM |
| Yeast Budding WM | Agaricus Stipe TS |
| Agaricus Pileus VS | Agaricus Stipe and Pileus VS |
| Puccinia Uredo on Wheat Leaf VS | Puccinia Teleuoto on Wheat Stem TS |
| Puccinia Aecidia On Barbery Leaf VS | Ustilago Spores WM |
| Ustilago with Host TS |
Breeding Nest
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Rotary Compressor Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Flow Over Weir Or Open Channel Apparatus
Flow Over Weir Or Open Channel Apparatus:
A ‘WEIR’ is the name given to concrete or masonry structure built across a river (or stream) in order to raise the level of water on the upstream side and to allow the excess water to flow over its entire length to the downstream side. Weirs may also be used for measuring the rate of flow of water in river or streams.
Different shapes of “WEIRS” generally used are sharp-crested weir, broadcasted weir and ogee shaped weir.
In the unit a centrifugal pump sucks the water from the sump tank, and discharges it to a small flow channel. The weir is fitted at the end of channel. All the weirs are interchangeable. The water-flowing over the weir falls in the collector. Water coming at from the collector can be directed to the sump or can be directed in to the measuring tank for measurement of flow.
SPECIFICATIONS:
[1] The unit is provided with following weirs: (a) Sharp-crested weir. (b) Broad-crested weir. (c) Ogee shaped weir. [2] Pump 1/2 H.P. monoblock. [3] Flow measurement – Measuring tank calibrated water flow meter is used. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Floor surface – 2.5 m x 1.5 m. [2] 230 v, 5 amp supply with earthing connectionXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Separatory Funnel
We bring forth the finest range of Separatory Funnel.
Our Separatory Funnel are designed in such a way that they make filling of carboys, drums and barrels very convenient.
The handles of these funnels make their handling very easy.
We offer these Separatory Funnel at market leading prices.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Separatory Funnel 100 ml | 2 | |
| Separatory Funnel 250 ml | 2 | |
| Separatory Funnel 500 ml | 2 |
Optical Bench, Aluminium
Description
Bench has two steel rods, one of which is graduated in mm with heavy metal and supports with leveling screws with four metal slides which slide smoothly on the bench. Two of the slides have transverse motion arrangement. Complete with two lens holders and two object needles. Graduated to 1 m Graduated to 1.5 m
Gear Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Gear Pump. The Set-up consists of a Gear Pump having a pair of meshed gears coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum Gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
Ø To determine overall efficiency and pump efficiency of the Gear Pump Ø To plot Head vs. Discharge, Pump efficiency vs. DischargeFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Oil Supply: Oil @ 30 Ltrs. (Optional extra cost)TECHNICALS SPECIFICATIONS:
Ø Pump : Gear Pump with pair of meshed gears Capacity 1 HP,Speed 1500 RPM (max.), Head 5 Kg/cm2 (max.) Ø Drive : AC Motor with step cone pulley arrangement for 3 prefixed speed DC Motor with DC Drive along with (non-contact type Digital RPM Indicator Ø Supply Tank : Capacity 30 Ltrs. Ø Measuring Tank : Capacity 20 Ltrs. fitted with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Control Panel : With required electrical instrumentation (The whole Set-up is well designed and arranged in a good quality painted structure.
Steering Geometry Wheel Alignment Trainer
Steering Geometry & Wheel Alignment Trainer
With the help of this trainer the students can learn about steering geometry and practically perform wheel alignment using various tools.
(A) Turn Tables
(B) Toe In Toe Out Gauge
(C) Magnatic Caster Camber Gauge
(D) Manual Steering System With Four Wheels
(E) Tool Kit
SAFETY GOOGLES
PRODUCT DESCRIPTION
- Economical goggle offers indirect venting and anti-fog coating for reduced fogging
- Polycarbonate lens absorbs 99.9 percent UV
- Meets the high impact requirements of ANSI Z87.1-2010 Standard
- Sturdy polycarbonate lens wide opening to fit over prescription eyewear
- Protective splash goggle clear lens
