XTEMOS ELEMENT
AJAX PRODUCTS TABS
Human Larynx With Tongue
Description
Natural size, three parts. Larynx showing cartilages, ligaments, muscles, relief of mucous membrane and thyroid gland. Tongue showing front part of the lower jaw which is detachable and separates into two parts, median section, sublingual gland and sub mandible gland are shown. on base with key card.
Pelton Wheel Turbine Test Setup
DESCRIPTION:
Pelton Wheel Turbine is only impulse water turbine now in common use named in honor of Sir L.A. Pelton (1829-1908) of California, USA. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the Inlet of the Turbine is only kinetic energy. The Pressure at the Inlet and Outlet of the atmospheric. This turbine is used for high heads. The Present Set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through SS nozzle with a SS spear, by means of Centrifugal Pump, tangentially to the runner. Row of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel the runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is providing with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid MS structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure Gauge is fitted at the Inlet of the turbine to measure the total supply head to the turbine.EXPERIMENT:
1.To study the operation of a Pelton Wheel Turbine 2.To determine the Output Power of Pelton Wheel Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 111 (1.33 HP) | HM 111 (2 HP) | HM 111 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1.5 Kw | 5 HP / 3.75 Kw |
| Discharge | 300 LPM (Approx.) | 400 LPM (Approx.) | 630 LPM (Approx.) |
| Supply Head | 25 m | 40 m | 45 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 150 Liters. | Capacity 200 Liters. | Capacity 300 Liters. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 7.5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1000 RPM (approx.) | ||
| Impeller | Material Brass, Bucket type | ||
| Nozzle | Material Stainless Steel/Mild Steel | ||
| Spear | Material Stainless Steel/Mild Steel | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
Carboys
Carboys, made of polypropylene, are much lighter than glass.
These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes.
We also offer carboy with stopcock for the esteemed clients.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Carboy 10 ltrs. | 1 | |
| Carboy 20 ltrs. | 1 | |
| Carboy With Stop Cock 10 ltrs. | 1 | |
| Carboy With Stop Cock 20 ltrs. | 1 |
Brush, Bottle
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Moving Coil Meters
Description
Meters are designed for D.C. measurements to meet every need of schools, colleges and technical institutions. All meters are housed in moulded dust proof cases with zero-adjuster and have connections terminals. Type MO-65 Round.| Case | : | ABS Plastic | |
| Accuracy | : | Class 2.5 | |
| Scale length | : | 50 mm. | |
| Overall size | : | 100x90x90 mm. approx. |
Ring & Ball
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Hall Effect Transducer
Voltage Measurement:
• One Voltage Signal conditioner is provided to interface with ADC • Output Voltage Range: (0-5V) • One Analog meter is provided to indicate the input voltage.Current Measurement:
• One Current Signal conditioner is provided to interface with ADC • Output Voltage Range: (0-5V) • One Analog meter is provided to indicate the input current. • Built-in Power Supply • One Auto Transformer is provided to vary the input voltage and current • 3½ Digit digital indicator
Digital Gauss Meter
Digital Gauss meter works on the principle of Hall Effect in semiconductor. When a semiconductor with current flowing in one direction is introduced perpendicular to a magnetic field a voltage is produced at right angles to the current path. The magnitude of this voltage is proportional to the intensity of the magnetic field. This voltage is called Hall Voltage. This Hall voltage is amplified and calibrated as magnetic field.
Specifications:
Range: 0-2 KG & 0-20 KG
Resolution: 1 G at 0-2 KG range
Display: 3½ digit LED
Power Supply: 220 V, ±10%, 50 Hz AC
Transducer: Hall probe-InAs
Pulley Blocks
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
CNC Mill Trainer1
CONTROLLER:
Type of Controller System : PLC based system under collaboration from tudor,uk Main Spindle Drive : D.C. Thyristor Drive, Inbuilt Safety X, Y and Z axis Drives : Stepper motor drive TTL Compatible Input to Stepper :Optically lsolated , motor drive TTL Compatible Interpolation : Linear, Circular parabolic Interpolation Code Used : G, M, S, T, F, I, K, M, F, Cycles : Circular Interpolation, Mirror, Pocket Milling Cycle Pocket & Helical Milling : Provided with Std Codes Real time tool path :with online 3D simulationTABLE:
Length x Width : 600 x 225 (approx.) Clamping Area : 450 x 160 (approx.) T Slots : 10mm slot width.MACHINE DETAILS:
Resolution : 5 micron(Standard) Distance from sindle :25-225mm(Nose to table top) Centerline to column :170mm Rapid Travel 700 mm/min Weight in kg : 950kg Dimension in mm : 1200 x 1200 x 1900 mmSPINDLE:
Spindle Speed : Continuous Variable Spindle power : 1.5 HP Inside Taper : ISO 30 Speed Range : 300 to 3000 RPM
Multiple Input/Output Process Trainer
Panel Features
• Power ON/OFF switch • Heater selection switch • Heater and pump indicators • High current fuse carrier for • Heater protection • Provision to run the stirrer • Digital panel meters • Two numbers of industrial PID Controller • Electrical test points are provided to measure the current signal • Mimic DiagramFeatures
• Two numbers of flow Transmitter (DPT) are provided to sense the flow of the liquid. • Three numbers of temperature transmitter (RTD) are provided at various stages to measure the temperature. • Five numbers of level sensor (RF capacitance) are provided to sense the level of each tank. • Industrial type Conductivity sensor is provided to analyze the conductivity of given Solution. • RTD sensor (or) Thermocouple acts as a temperature sensor. • Digital panel meters are provided to indicate the output of each sensor. • Provision to measure the conductivity. • Two numbers of motorized control valve or pneumatic control valve are provided to control the flow of the pipe line. • A powerful thyristor based power driver is provided to drive the heater power. • An industrial type water heater is used as a heat Source. • Storage tank of 50 litre capacity (SS). • Process tank of 15 litre capacity (SS). • Four numbers of acrylic tank are provided to study the response of four tank systems. • In necessary location Ball valve, globe valve and needle valves are provided. • Two numbers of stirrer are provided in the temperature process and alkaline process. • Three numbers of centrifugal pump (FHP) is used to circulate the water from storage tank. • Six numbers of rotameter are provided in the process inlet to visualize the real flow. • Regulated power supply is mounted in the panel. • All the flow lines are fitted by (SS) pipe fitting. • An over head tank is provided to give constant flow. • All the equipments are mounted in a rugged and mobile type metallic work station.
Sonometer 3-Wire
Description :-
Hollow wooden sounding box 1290 x 130 x 110 mm, with mm scale, has two fixed bridges 72 cm apart over which wires are stretched.
To one wire is fitted a spring balance reading to 100 N x 5 N and its tension can be adjusted by a winged nut and measured.
Another wire passes over a pulley and can be loaded as desired.
A third wire, for comparison, can have its tension adjusted by a wrest-pin.
With 3 movable bridges, wrest-pin key, spring balance, and set of four wires of different diameters, each 1.5 meter long, without masses.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Number Mat
Get kids to think on their feet! Number mat is fast and crazy quiz games make learning math fun!Kids listen the equation from teacher, do the math, and then step on the right answer. Play different games to reinforce numbers, counting, addition and subtraction up to the number 25. Great for classroom use. Mat measures 20 feet in length.
Thermistor Unit
Digital Colorimeter
Description
The basic set-up of the colorimeter is: LED light source: Produces polychromatic light over the entire visible region, 45 Broad spectrum filter: The colorwheel has nine different filters. The filter employed is selected by wavelength. Each filter will produce monochromatic light at a specified peak wavelength with a bandpass of 20 mm. The filters enable the user to perform tests from 400 to 680 nm. Cuvette Holder: It holds the inserted cuvette during testing. It is imperative the cuvette be consistently oriented in the holder. Round cells usually have orientation markings to correctly position the cuvette. Detector: A silicon photo diode is used as the detector. The photo detector current will change as a function of light energy. Display:The current signal from the detector is converted to a numerical value, absorbance and is shown on led displayXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Episiotomy Training Simulator
Description
Suturing Simulators provide a realistic way for students to learn good surgical techniques. The simulators provide students with a variety of repair experiences without the constraint of time and concern for safety, which are factors with a live patient. The simulators can be used by the student in a learning lab with an instructor or by the student individually in the clinical setting just prior to a patient experience. They are also useful as homework teaching aids that can be signed out at night and returned the next day. In addition to being portable, the lifelike texture allows the learner to develop a “feel” for instrument handling, tension on suture, and the advantages of one method of tying knots over another.Includes one of each simulator:
Midline Suture Simulator Left Mediolateral Suture Simulator Right Mediolateral Suture Simulator Each simulator comes with an instruction booklet and is individually boxed.
Reynold S Apparatus
DESCRIPTION:-
The Set-up is designed to verify Reynold’s Apparatus experimentally. The Apparatus consists of a glass tube which one end having bell mouth entrance connected to a water tank. At the other end of the glass tube a cock is provided to vary the rate of flow. Flow rate of water can be measured with the help of Measuring Cylinder and Stop Watch, supplied with the set-up. A capillary tube is introduced centrally in the bell mouth. To this tube dye is fed from a small container, placed at the top of Constant head Tank, through polythene tubing.EXPERIMENTS:-
Ø To study different types of flow. Ø To determine the Reynold’s Number and hence the type of floe either laminar or turbulent.UTILITIES REQUIRED: -
Ø Water Supply. Ø DrainTECHNICAL SPECIFICATION: - | ||
| Ø Tube | : | Material Borosilicate Glass |
| Ø Dye Vessel | : | Material SS, Suitable Capacity |
| Ø Capillary Tube | : | Material Copper/Stainless Steel |
| Ø Constant Head Water Tank | : | Capacity 40 Liters. |
| Ø Water Circulation | : | FHP Pump |
| Ø Flow Measurement | : | Using Measuring Cylinder |
| Ø Sump Tank | : | Capacity 60 Liters |
| Ø Stop Watch | : | Capacity 60 Liters. Electronic |
| Ø Control Panel Comprises of | : | Standard make, On/Off Switch, Mains Indicator, etc. |
| Ø The Whole set-up is well designed and arranged in a good quality painted structure. | ||
