XTEMOS ELEMENT
AJAX PRODUCTS TABS
Meker Burner, with Stopcock
Resistance Coil, Economy
Lens, Biconvex, Acrylic
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Ohm’s Meter
Multi Stage Centrifugal Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Multi Stage Centrifugal Pump. The Set-up consists of a Multi Stage Centrifugal Pump coupled with DC motor & drive, supply tank, measuring tank & pipe fittings for closed loop water circulation. There are 2 separate pumps connected to DC Motor and drive and can be connected in series and parallel to stimulate different combinations. Pressure and Vacuum Gauge are connected on delivery and suction side of each pump for the purpose of measurement. Swinging Field Dynamometer arrangement for direct torque measurement using dial type spring balance is made for individual pump. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENTS:
1.Speed Vs Discharge 2.Head Vs Discharge at various speeds 3.Efficiency curves at various speed and headsFEATURES:
1.Closed loop water circulation 2.Compact & stand alone set-up 3.MS Excel sample calculation program on demand 4.Stainless Steel tanks and wetted parts 5.Superb painted structure 6.Simple to Operate & MaintainUTILITIES REQUIRED:
1.Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC), 5 A, three pin socket with switch for pump. 2.Water Supply: Tap water connection ½” BSP. Distilled water @ 80 Ltrs. (Optional extra cost)TECHNICAL SPECIFICATIONS:
1.Pump (2 Nos.) : Kirloskar, Capacity 1 HP Speed 2800 RPM (max.) Head 12 m (max.) 2.Drive : DC Drive along with non-contact type Digital RPM Indicator 3.Supply Tank : Capacity 150 Ltrs. 4.Measuring Tank : Capacity 100 Ltrs. fitted with Piezometer Tube & Scale 5.Piping : GI / PVC 6.Stop Watch : Electronic 7.Control Panel : With required electrical instrumentation The whole Set-up is well designed and arranged in a good quality painted structure.
3Φ IGBT Power Module
FEATURES:
• 4 IGBT modules have totally 8 nos of IGBT’s rating @ 1200V/75A to form 3Φ VSI • 8 Nos of high speed IGBT driver with isolation • Diode bridge rectifier 60A 1200V with filter capacitor provided for DC-rail voltage upto 900V • FRC connectors are provided for IGBT Gate PWM Inputs (For Interfacing with different Controller) • 5 nos of Hall Effect Current Sensors and one no of Voltage Sensor is provided to sense the DC link current, 3Φ output current and DC link voltage • Separate 230V AC Input for driver Circuit ±15V DC for control Circuits • 3 pole MCB is provided for Input Power ON/OFF • Inverter Output terminated by Banana Socket in the front panel • All PWM, Current, Voltage signals are provided in the front panel for testing purpose • Short circuit, over voltage and over current protections are available • These protections are indicated by the protection LED • Voltmeter is provide to indicate the DC voltage • Reset switch is provide for reset the TRIP function
Slide Mailer
We present to our esteemed clients, Slide Mailer.
The Slide Mailer is the best option to carry prepared slides from one place to another.
Moulded in Polypropylene, these Slide Mailers are available in three sizes i.e.1, 2 & 5 slides.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Slide Mailer - 1 Slide | 25 | |
| Slide Mailer - 2 Slides | 25 | |
| Slide Mailer - 5 Slides | 25 | |
| Slide Mailer - 10 Slides | 25 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Milling Tool Dynamometers
This is a simple and essay to understand set up introduce by sharp techno systems to study the behavior of cutting forces during milling operation in three directions. With this unit students can evaluate cutting depth, speed and feed. The unit works on standard method of octagonal ring with strain gauges. It is in to part one mechanical rings sandwiched between two M.S. plate with strain gauges fixed on it. This set of octagonal rings transmits the relevant data to the force indicator during milling operation.
FEATURES
1.Rigid construction & Compact Unit. 2.Assessment of cutting forces by giving due consideration to various parameters like depth of cut, material, cut, material, speed and feed. 3.Eassy in handling & Digital force indicators to measure three forces simuleniously.SPECIFICATIONS-
1.Mechanical sencing unit with set of octagonal rings and strain gauges. 2.Three channel digital force indicator with balancing potentiometers and polycarbonate front plate. 3.Range of force measurement in coordinate direction – 0 to 500 kg. 4.Over all size of mechanical unit- 300 x 300 mm.SERVICE REQUIRED
1.Necessary Milling Machine with automatic feed arrangement and tooling 2.230 volts, single phase, 50 Hz stabilized power supply.
Abney Level Made of Brass pipe
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
ZigBee Debugger/Dongle
Recalculating Ball Type Steering System
Recalculating Ball Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Bridge Rectifier
Bridge Rectifier is made of four diodes connected in a bridge circuit. It is housed in a plastic moulded box. This bridge rectifier converts alternating current (AC) into direct current (DC). It provides the same output polarity for either input polarity. All the electronic devices require direct current, so bridge rectifiers are used inside the power supplies of almost all electronic equipment. For the easy understanding of the internal circuitry, the circuit diagram is printed on the box.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Telescopic Alidade
Electronic Balance
Vernier Calipers Digital
Vernier Calipers Digital
• Hardened Stainless Steel construction, bright LCD display.
• Easy push button Metric English conversion.
• Operates on one 1.5V silver oxide battery (included).
• Automatic shut off.
• 0-150mm x 0.01 mm / 6 inches x 0.0005 In.
• Comes complete with foam lined sturdy case, and instructions.
Three Hinged Arch Apparatus
The mild steel model has a span of 100cm and rise 25cm, with hinges at supports and crown. One of the ends should rests on rollers. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically determinate structure, the horizontal thrust developed under the action of any load system can be theoretically calculated and will also be measured directly by neutralizing the outward movement of the roller end. A dial gauge with 25mm travel (with magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Storage Vial
These polypropylene vials add to the existing range of Polylab storage vials.
Available in 5 ml. & 10 ml. capacities, these vials have polypropylene cap with built in seal ring which makes it a leak proof vial.
These vials are also used for the storage of biological material, animal & human cells etc.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Storage Vail 2.0 ml | 500 | |
| Storage Vail 5.0 ml | 500 | |
| SV - 10 ml | 500 | |
| SV - 5 ml | 500 |
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Plain Laboratory Desiccator
We offer premium range of Plain Laboratory Desiccator which can be availed at market leading price range. Plain Desiccator have excellent quality and durability.
Grease should be applied on the flanges to make it air tight.
Material : Polypropylene/ Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Desiccator (Plain) PP/PC 150 mm | 1 | |
| Desiccator (Plain) PP/PC 200 mm | 1 | |
| Desiccator (Plain) PP/PC 250 mm | 1 | |
| Desiccator (Plain) PP/PC 300 mm | 1 |
Linear IC Trainer
This Trainer Consist of :
1. Regulated power supply of ± 12 V / 250 mA.
2. Variable 0 to ±5 V / 250 mA.
3. Sine wave oscillation of 1 KHz.
4. Digital Voltmeter of 0-20 V DC, LCD display, 3 ½ Digit.
5. Functional diagram of IC 741 is printed with 2 mm sockets.
6. One extra 8 pin IC Base with 2 mm sockets.
7. Potentiometer of 10K Ohms.
8. Required Resistance and Capacitances mounted on board.
9. Interconnection Leads and Manual to perform 15 experiments on IC741 e.g. inverting, non-inverting, summing, difference, multiplier, differentiator, integrator etc.
