XTEMOS ELEMENT
AJAX PRODUCTS TABS
Hand & Table Microtome
The Hand & Table Microtome is used to cut thin sections of Microscopic materials, such as specimen parts of plants and animals.
It is Considered as the basic form of a microtome permitting microtomic cuts by hand in a quick and accurate way.
The microtome is suitable for practical courses in microscopy, for field work during excursions, for school education and for a serious amateur of biology.
Refrigerant Charging Unit
This charging unit is fitted with motorised vacuum pump and other safety devices like pressure gauge. With the help of this charging unit students can charge the refrigerant gases into compressor or store the gas of a refrigerator or air conditioner inside the cylinder fitted inside the charging unit that can be used later.
Structure of bone model
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Burner Bunsen-Economy
Description
This is one of most inexpensive option without flame stabilizer. The burner tube is made of brass and mounted on pressed steel powder coated base. Base dia is 80 mm. overall height of burner is 135 mm burner tube dia 12 mm. Suitable for LPG / Butane gas.Burner Specifications :
Tube Dia. - 12 mm Height - 130 mm Weight - 160 g
Numerical System
This panel is used to demonstrate the number systems such as binary, decimal and hexadecimal numbers. Toggle switches used to activate the displays showing the particular number entered. Input may be entered either as decimal or binary numbers with a toggle switch for mode selection. Decimal numbers are shown on a three digit seven segment LED display. 12 V / 2 A DC adaptor is required to operate it.
Needle Steel Handle
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
CNC Lathe Trainer
Controller:
Type of control system: PLC based system Main Spindle Drive : AC Motor with VFD Z and X Drives : Stepper drive with Ramp function Input to Stepper : Optically Isolated Motor Drive :TTL Compatible Run Speed Control : Computer controlled with software Interpolation : liner / Circular /Parabolic Cycles Used :G,M,S,T,F,I,K,M,F Cycles : Circular Interpolation /canned Threading : Straight/Taper Power Devices : Short Circuits and over Temperature Protected Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
Center height : 100mm Swing over Carriage : 80mm Distance between Centre : 300mm Longitudinal Travel : 310mm Weight : 800kg Dimension in mm : 1300 x 800 x 1400 Rapid Travel : 700mm/min Resolution Z Axis : 5micron Resolution X Axis : 5micron Automatic : providedAXIS TRAVEL:
X Axis : 80mm Z Axis : 310mmSPINDLE:
Spindle Speed : Continuous Variable Spindle Power : 2 HP Inside Taper : MT3 Speed Range : 50 to 3000Rpm
TMS320F2812 Based DSP Trainer
FEATURES:
• 12 Motor control PWM & 4 Individual PWM output • 16 channel, 12 bit ADC • 56 Individually programmable GPIO lines • 2 Quadrature encoder interface / 6 capture input • 128K x 16 bit flash memory • 1K x 16 bit OTP ROM • 14K x 16 bit SARAM • 16 LEDs are provided for user program development & debug • Opto isolated USB to Serial Interface • 3 Switches are provided for user interface like, frequency, speed variations etc., • Bead Inductances provided for RF EMI rejection • 16 ADC inputs are protected and terminated at 26 Pin FRC connector. • 8 I/O lines are protected and terminated at 50 Pin FRC connector • 12 PWM outputs and 6 capture inputs are terminated at 34 pin FRC connector • On board isolated USB to JTAG interface
Dicot & Monocot Leaves
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Meiotic Cell Division
Multi Functional I.V. Training Arm
Description
The I.V. Injection Arm P50/1 made of silicone, is unique in quality and design and allows realistic training to teach competence to medical staff. It is also very suitable for group instruction because of its high quality, stain resistance and easy-to-clean soft material.It is ideal for practicing the following:
Correct puncture of peripheral veins for blood sampling. The following veins can be punctured: basilica vein, cephalic vein, median cubital vein, dorsal venous rete of hand Intravenous injections Positioning of a butterfly catheterDelivered in deluxe storage carton with:
1 injection arm with already mounted tubing system 1 infusion bottle 1 stand 1 bottle of artificial blood concentrate(250ml) 1 plastic cup 1 disposable syringe and 2 injection cannulas (recommended cannula size: 20 and 21 gauge) 2 tubing systems as replacement parts 1 container of talcum powder
Embryonic Development (Period Of Gestation)
Description
A set of nine detailed models, mounted on stands, showing the following stages: An Embryo About 6 Days Old, Considerably Enlarged. Uterus With The Embryo In 1st Month Of Gestation. Uterus With The Embryo In 3rd Month Of Gestation. Uterus With Foetus In 4th Month. Uterus With Foetus, Placenta And Umbilicle Cord. Uterus With Foetus In 5th Month. Uterus With Foetus In 7th Month Of Pregnancy. Uterus With Foetus In 8th Month Of Pregnancy. Uterus With Foetus In 9th Month Of Pregnancy. Complete With Key Cards.
Milling Tool Dynamometers
This is a simple and essay to understand set up introduce by sharp techno systems to study the behavior of cutting forces during milling operation in three directions. With this unit students can evaluate cutting depth, speed and feed. The unit works on standard method of octagonal ring with strain gauges. It is in to part one mechanical rings sandwiched between two M.S. plate with strain gauges fixed on it. This set of octagonal rings transmits the relevant data to the force indicator during milling operation.
FEATURES
1.Rigid construction & Compact Unit. 2.Assessment of cutting forces by giving due consideration to various parameters like depth of cut, material, cut, material, speed and feed. 3.Eassy in handling & Digital force indicators to measure three forces simuleniously.SPECIFICATIONS-
1.Mechanical sencing unit with set of octagonal rings and strain gauges. 2.Three channel digital force indicator with balancing potentiometers and polycarbonate front plate. 3.Range of force measurement in coordinate direction – 0 to 500 kg. 4.Over all size of mechanical unit- 300 x 300 mm.SERVICE REQUIRED
1.Necessary Milling Machine with automatic feed arrangement and tooling 2.230 volts, single phase, 50 Hz stabilized power supply.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Optical Bench, wooden
Description
A wooden base board with one meter scale divided into mm with following accessories: One each White face object and receiving screens each 150 x 100 mm with aperture mounted on wooden base with an index mark. Two plane mirrors 150 x 100 mm mounted as above. One lens holder V shaped, wooden. One needle vertically mounted in a short wooden rod on base. One candle holder on base. The components have the same optical center height.
Tubing, Rubber, High Pressure
Coriollis Component Of Acceleration
This set up is designed to study coriollis component of Acceleration of a slider crank Mechanism. The apparatus uses hydraulic analogy to represent the rotating slider. It consists of a rotating block with two arms in opposite direction. These tubes can be rotated at various speeds by using a swinging field motor, which also acts as a dynamometer to measure torque applied to rotating tubes. A Perspex window on top cover helps to visualize the process. Rotameter is used to measure water flow rate through tubes. Water is circulated by small monoblaock pump.
Specifications:
1.Main Tank with fiberglass lining. 2.Rotating Arms 9/6 mm dia, 300 mm long. 3.Motor – Swinging field, D.C., 0.5 HP. 4.Rotameter 5.Monoblock Pump 6.Control Panel comprising of – (i) Speed Control Unit. (ii) Speed Indicator. (iii) Necessary switches. 7.Rigid support frame.Range of Experiment:
Coriollis Component of Acceleration can be determined at various speeds of rotation and water flow rates.Service Required:
1.A.C. Single Phase .230 V. stabilized supply. 2.Floor Space -1.5 m X 1.5 m.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
PP Cryo Box
We bring forth the finest range of PP Cryo Boxes.
Moulded in Polypropylene, the top of the box is attached to the bottom through well designed built-in hinges.
The bottom has built-in spaces to hold vials up to 2 ml. Capacity.
Available in two different sizes, these autoclavable PP Cryo Boxes bear alpha numeric index for easy identification of different vials placed inside.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Cryo Box (P.P) - 81 places for 1 ml or 1.8 ml cryo vails | 4 | |
| Cryo Box (P.P) - 100 places for 1 ml or 1.8 ml cryo vails | 4 |
Water Cooler Trainer
The apparatus consists of a storage water tank, embraced by evaporator coil of the cooling unit, cooling cycle comprises of a hermetically sealed compressor, air-cooled condenser, a capillary tube as expansion device and an evaporator cell. The stainless steel water tank is provided with insulation on air Sides and a door are provided at the top. Cold water can be taken out from a top provided and inlet water supply is controlled by a bail-operated top. Various measurements provided enable students to determine the theoretical and actual COP, power consumption, actual cooling capacity refrigerant flow and compressor volumetric efficiency of compressor.
SPECIFICATIONS:
Cooling Cycle a) Compressor Hermetically sealed type, having the capacity of 1/3 ton of refrigeration using R-12 refrigerant. b) Finned tube type air colled condenser with forced air flow. c) Filter cum drier for refrigerant. d) Capacity expansion device. e) Evaporator coil embraced on stainless steel water tank, Provided with glass wool Insulation. 2.Water drain tap and float operated inlet water tap are provided for water tank with insulated lift door at top. 3.Measurement a) Pressure gauges for evaporating and condensing pressure. b) Thermometers to measure refrigerant temperatures at inlet and out let of condenser and evaporator. c) Dial type thermometer for water temperature. d) Rotameter to measure liquid refrigerant flow. e) Energymeter to measure compressor Input. 4.Safely & Controls – a) Thermostat to put off compressor at set water temperature. b) Pressostat to put off compressor if high or low pressure Goes out of set limit. c) Over load protector for compressor, A technical manual will be supplied along – with the unit. Also, the unit is provided with an attractive and anti corrosion powder costing.SERVICES REQUIRED:
1.Floor space of 1.5 m. X 1.5 m. 2.Water supply of 5 lit/min, 3.230 V, 15A AC stabilized supply with earthing connection
Ripple Tank
Description :-
Transparent acrylic plastic ripple tank, supported in a sturdy plastic frame which has recesses to hold four legs with leveling feet.
The tank edges are shaped to minimize undesired reflections.
Tank has a drain hole closed by a rubber stopper.
With two light alloy uprights to carry a horizontal rippler support rod which is adjustable for height.
The ripple assembly, elastically suspended from the support rod, consists of a 4 – 6 V DC motor mounted on a wooden beam.
The motor has an eccentric weight which causes the beam to oscillate.
Two point sources are provided by two plastic spheres, each mounted on a right angle rod.
A metal rod is fixed centrally into a socket in one short side of the frame to afford support to the illuminant.
Overall size of the tank 580 x 500 x 80 mm, window area 370 x 280 mm, height of tank above bench level (with legs attached) approx. 375 mm.
Complete with following accessories :-
1. Two straight obstacles of aluminium alloy length 130 mm.
2. One straight obstacle length 40 mm.
3. One curved reflector radius 200 mm.
4. One trapezoidal plastic plate for refraction.
5. One wood hand wave roller.
6. One water dropper.
7. One pkt. rubber bands.
8. One foam plastic sponge.
9.One illuminant with a 12 V, 24 W lamp mounted in a lamp house and provided with a long supporting rod.
Centrifugal Blower Test Rig
The apparatus consists of a spiral casing, which houses an impeller. Impeller is driven by a variable speed D.C. motor. Three, interchangeable impellers, viz. Radial forward and Backward curved vanes are provided with the unit. Digital indicators are provided for speed of impeller. A venture provided measures the discharge. Thus students can evaluate the performance of different impellers at various speeds.
