XTEMOS ELEMENT
AJAX PRODUCTS TABS
Rear Axial Assembly With Differential Gear Semi
Rear Axial Assembly With Differential Gear Semi Floating Type – Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Crucibles Porcelain Gooch
Bridge Rectifier
Bridge Rectifier is made of four diodes connected in a bridge circuit. It is housed in a plastic moulded box. This bridge rectifier converts alternating current (AC) into direct current (DC). It provides the same output polarity for either input polarity. All the electronic devices require direct current, so bridge rectifiers are used inside the power supplies of almost all electronic equipment. For the easy understanding of the internal circuitry, the circuit diagram is printed on the box.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Decade Inductance Box – 7 Dial
Description
Housed in a box with seven dials and fitted with 4 mm output plugs, the unit allows a range of inductances from 1ΩH to 10ΩH. 7 Decade Inductance Box (i) 1ΩH to 10ΩH in steps of 1ΩH (ii) 10ΩH to 100ΩH in steps of 10ΩH (iii) 100ΩH to 1mH in steps of 100ΩH (iv) 1mH to 10mH in steps of 1mH (v) 10mH to 100mH in steps of 10mH (vi) 100mH to 1mH in steps of 100mH (vii) 1mH to 10mH in steps of 1mH
Ticker Tape Timer
For the measurement of velocity and acceleration, using timing marks made on a moving paper tape by a vibrating striker.
Designed to operate on a 12V A.C. supply and uses the mains frequency as its timing standard.
The unit is housed in a moulded case including mounting flanges.
The top of the case caries a tape guide which incorporates a carbon paper disc support and an adjustable anvil for the striker point.
All moving parts are fully enclosed and a pair of 4mm sockets are provided on the side of the case for connection of the electrical supply.
Supplied with a roll of self marking paper tape.
Paper tape : 100m of paper tape, 9.5mm wide.
Carbon Paper Discs : 40mm diameter, with 3mm hole, cut from long life plastic film type carbon paper.
Dishes, Crystallizing
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Fiber Optics Communication Set
Objective:
To construct an optical transmitter and transmission of signal through Fiber Optics Cable. To construct an Optical Receiver and study the Attenuation of Signal when transmitted from Transmitter to Receiver end. Analog and Digital link can also be studied as this unit is complete with Sine and Square Waves. Bending losses can also be studied.
Features:
Instrument comprises of Microphone Preamplifier stages consists of MIC (Microphone), Preamplifier and Amplifier (Voice is converted to electrical signal and then amplified) and fed to LED (Transmitter) and then through fibre cable, signal is sent to Photodetector (Transistor) and again amplifier and output is sent to Speaker Unit. Power Supply of +6 VDC is used in Amplifier ckt. 2 No. Fiber Optics cables are provided (one of them is 50 cm long and the other is 100 cm long). One more fiber cable of 50mm length having connector at one end is also provided. Connectors a both end of fiber cable are provided for insertion in sockets provided on the front panel. Bending losses can also be studied in long wire.
Standard: MIC with 2 meter long lead and a Speaker 4, 4 ohm are mounted in a vertical box.
Accuracy: with 1 meter long connecting leads. 2 No. Fiber optic cable having length of 50 cm and 100 cm are provided.
Optional : Digital multimeter (3 1/2 Digit, Big size Display) This model also include Digital Multimeter and wooden frame for measurement of Numerical aperture i.e. complete in all respect including facility for measurement of numerical aperture.
Emitting Diode (LED’s)
Bridge rectifier is designed with four LEDs internally arranged in bridge pattern fitted inside a plastic moulded case. Two LED’s are red and two LED’s are green. This device is used to demonstrate the functioning of a bridge rectifier, i.e., to convert alternating current (AC) into direct current (DC). Two yellow sockets are used for AC input. Two sockets, one red and one black, are used for DC output. For the easy understanding of the internal circuitry, the circuit diagram is printed on the box.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Dissolution Rate Test Apparatus
Description
Dissolution rate test apparatus is designed to carry out simultaneously SIX TESTS of dissolution rate of tablets & capsules as per USP standards. Dissolution Rate Test Apparatus consists of water bath made of transparent acrylic fitted with an inbuilt water circulation system. Machine has a DUAL TEMP. SENSOR system which controls both water bath temperature within +/- 0.1º C & senses the temperature of jars. The motor is digitally controlled to give speed between 20 to 160 RPM precisely within +/- 1 RPM. The micro-processor also have digital timer to control test timings from 00:01 to 99:59 (HH:MM). The machine is fitted with a LCD Display which keeps the user updated about the RPM, TIME & TEMPERATURE all the time. The unbreakable jars prevent accidents related to breakage & spilling of media in the lab. The jars have acrylic lids which allow passing of stirring shaft. The shafts are suspended from the top & are operated by the motor. Stirrer Assembly can be lifted with auto lifting mechanism for easy operations.Specifications
| Speed: | Variable from 20 to 160 with accuracy of +/- 1 RPM. | |
| Temperature | 30º C to 80º C (+/- 0.5º C) | |
| Timer | 00:01 to 99:59 Hrs. with alarm. | |
| Display | 20 x 4 LCD Display | |
| Bath | Made up of 8 mm thick clear acrylic (10mm Optional) | |
| Heater | 1000 Watts Stainless Steel | |
| Sensor | Dual Sensor System (PT-100) | |
| Auto Lifting Assembly | Available | |
| Jars | Unbreakable Ploycarbonate clear jars (6 Nos.) | |
| Power | 220 / 230V AC, 50 Hz |
Citical Radius Of Insulating Material
Citical Radius of Insulating Material:
At particular radius of insulation over a cylinder, loss of heat is maximum. The unit consists of a G.I. pipe provided with plaster of Paris insulation on out side surface. Four pipes are provided with heater inside having input control. Input to heaters is measured by common voltmeter and ammeter, by controlling input to heaters, it is shown that critical radius of insulation is ratio of thermal conductivity and outside heat transfer co-efficient.
SPECIFICATIONS:
1.G. I. Pipes with electrical heater inside – 4 Nos. 2.Insulation over the pipes of different thickness. 3.Controls and Measurements – a) Dimmerstat to control heater input – 4 Nos. b) A voltmeter and ammeter to measure inputs to heater. c) Digital temperature indicator to measure temperatures across insulation. d) Necessary switches and controls. A technical manual accompanies the unit.SERVICES REQUIRED:
230 V, 5 Amp., A.C., Supply with earthing connection. Floor Area of 1 m. X 1 m X 1.5m. height.
SILICA BASIN (Round Bottom) with spout
PRODUCT DESCRIPTION
Round Bottom Basin With Spout is high purity material that enables products to resist corrosion and withstand the sharp change in temperature. Both of them meet requirements acquired by chemical and physical analysis and have 200ml Capacity.
Available in Different Dimensions:
20ml, Dia. 55mm x Ht. 23mm
45ml, Dia. 75mm x Ht. 27mm
70ml, Dia. 87mm x Ht. 33mm
85ml, Dia. 94mm x Ht. 36mm
100ml, Dia. 100mm x Ht. 45mm
200ml, Dia. 113mm x Ht. 47mm
Dicot Plant Stem
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Ticker Tape Timer
For the measurement of velocity and acceleration, using timing marks made on a moving paper tape by a vibrating striker.
Designed to operate on a 12V A.C. supply and uses the mains frequency as its timing standard.
The unit is housed in a moulded case including mounting flanges.
The top of the case caries a tape guide which incorporates a carbon paper disc support and an adjustable anvil for the striker point.
All moving parts are fully enclosed and a pair of 4mm sockets are provided on the side of the case for connection of the electrical supply.
Supplied with a roll of self marking paper tape.
Paper tape : 100m of paper tape, 9.5mm wide.
Carbon Paper Discs : 40mm diameter, with 3mm hole, cut from long life plastic film type carbon paper.
Plane Table
Description
The Plane Table Surveying Instruments include standard accessories like Trough Compass, Spirit level, Canvas cover, Plumbing Fork etc., and is also with a fitted tripod. Uses of Plane Table in Engineering Surveys: • Maps preparation • Recording topography Accessories included in Plane Table Surveying Instruments: • Plane Table Board 750 x 600 mm, thickness 22mm & 16mm • Carrying Bag for Board • Teak wood Polished Stand • Stand Rigid Brass Head & Plate, • Magnet Trough compass brass • Spirit Level brass • Sight van 24" • Plumbing Fork • Plumb Bob
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Tuning Forks welch type
Description :-
Consists of aluminum tuning forks, mallet in a wooden box.
Tuning forks are stamped with frequency and note.
Set of 8 (C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512)
Set of 13 (G-100, C-128, C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512, C-1024, C-2048 and C-4096)
Set of 8 (C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512)
Set of 13 (G-100, C-128, C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512, C-1024, C-2048 and C-4096)
Water Cooler Trainer
The apparatus consists of a storage water tank, embraced by evaporator coil of the cooling unit, cooling cycle comprises of a hermetically sealed compressor, air-cooled condenser, a capillary tube as expansion device and an evaporator cell. The stainless steel water tank is provided with insulation on air Sides and a door are provided at the top. Cold water can be taken out from a top provided and inlet water supply is controlled by a bail-operated top. Various measurements provided enable students to determine the theoretical and actual COP, power consumption, actual cooling capacity refrigerant flow and compressor volumetric efficiency of compressor.
SPECIFICATIONS:
Cooling Cycle a) Compressor Hermetically sealed type, having the capacity of 1/3 ton of refrigeration using R-12 refrigerant. b) Finned tube type air colled condenser with forced air flow. c) Filter cum drier for refrigerant. d) Capacity expansion device. e) Evaporator coil embraced on stainless steel water tank, Provided with glass wool Insulation. 2.Water drain tap and float operated inlet water tap are provided for water tank with insulated lift door at top. 3.Measurement a) Pressure gauges for evaporating and condensing pressure. b) Thermometers to measure refrigerant temperatures at inlet and out let of condenser and evaporator. c) Dial type thermometer for water temperature. d) Rotameter to measure liquid refrigerant flow. e) Energymeter to measure compressor Input. 4.Safely & Controls – a) Thermostat to put off compressor at set water temperature. b) Pressostat to put off compressor if high or low pressure Goes out of set limit. c) Over load protector for compressor, A technical manual will be supplied along – with the unit. Also, the unit is provided with an attractive and anti corrosion powder costing.SERVICES REQUIRED:
1.Floor space of 1.5 m. X 1.5 m. 2.Water supply of 5 lit/min, 3.230 V, 15A AC stabilized supply with earthing connection
Tape Measures
Both sides metric or one side metric and other in feet-inches Fiber glass with PVC covering.
Non-conducting, waterproof, washable, and water-resistant.
Case made of zinc-coated steel sheet, covered with vinyl, & fitted with a flush winding handle.
all metal fittings are chrome-plated.
The Tape Measures are provided in size 5 meters, 10 meters, 15 meters, 20 meters, 25 meters, 30 meters.
