XTEMOS ELEMENT
AJAX PRODUCTS TABS
Tubing, Rubber, Extra Soft
Measuring Cylinder (Round Base)
We are a credible Exporter and Supplier of Measuring Cylinder (Round Base).
Measuring Cylinder is laboratory equipment used to measure the volume of a liquid.
It is more accurate and precise than laboratory flasks and beakers.
Sometimes, Measuring Cylinder is also used to indirectly measure the volume of a solid by measuring the displacement of a liquid.
Available in high grade polypropylene or polymethylpentene material, our Measuring Cylinder comes with molded graduations in variegated divisions and capacities.
They are transparent and possess optimum resistant against chemical.
They have a round base and pouring spout.
We make available Measuring Cylinder as per the requirement at the best market prices.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Measuring Cylinder 10 ml | 24 | |
| Measuring Cylinder 25 ml | 12 | |
| Measuring Cylinder 50 ml | 12 | |
| Measuring Cylinder 100 ml | 12 | |
| Measuring Cylinder 250 ml | 6 | |
| Measuring Cylinder 500 ml | 4 | |
| Measuring Cylinder 1000 ml | 3 | |
| Measuring Cylinder 2000 ml | 2 |
Bending Moment & Shear Force Apparatus
INTRODUCTION:
Shear Forces occurs when two parallel forces act out of alignment with each other. For example, in a large boiler made from sections of sheet metal plate riveted together, there is an equal and opposite force exerted on the rivets, owing to the expansion and contraction of the plates. Bending Moments are rotational forces within the beam that cause bending. At any point within a beam, the Bending Moment is the sum of: each external force multiplied by the distance that is perpendicular to the direction of the force.EXPERIMENT MANUAL:
1. To verify the Shear force a cross-section of the beam. 2. To verify the bending moment in cross–section of beam with a flexure condition.APPARTUS SPECIFICATION:
1. Dimensions : 158 cm X 45cm X (h)60cm 2. Total Beam Length : 160 cm with flexure 3. Width of Beam : 5 cm 4. Distance of Length in between : 5 cm 5. Height of beam : 36 mm 6. No. of Hanger for weights : 3 7. No. of Spring Balance : 2 (of 10kg) 8. Total Weight of Apparatus : 13.1 kgACCESSORY REQUIRES:
1. Shear force apparatus 2. Bending Moment Apparatus 3. Hangers 4. Weights 5. Two Spring balances – 10kgs
Charle’s Law Kit
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Measuring Tape
Description
Measuring tape is a flexible form of ruler. It consists of a ribbon of cloth, plastic, fiber glass, or metal strip with linear-measurement markings. It is a common measuring tool. Its flexibility allows for a measure of great length to be easily carried in pocket or tool kit and permits one to measure around curves or corners.
Automotive Stethoscope
When components of an automobile engine are not functioning properly, they usually sound a warning in the form of noises not common to normal operations. Fortunately most noises posses characteristics of their own which help to identify the sources, coupled with some knowledge of their meaning. The unit is consisting of earphone, amplifier, switch and carbon microphone, assembled in a polished wooden box, Furnished with instructions, and a chart of possible different noise, probable source, mike position and how to check.
Thermal Conductivity Of Insulating Powder
The apparatus consists of an insulating powder, which is enclosed in a cavity of two concentric spheres. The inner space of the inner sphere contains the mica heater. Input to the heater can be adjusted by the dimmerstat. The tappings on the surfaces of the inner sphere and outer sphere are used to find out the temperature difference between the spheres. This enables to find out the conductivity of powder.
Specifications:
1.Inner sphere dia. 100mm and outer sphere dia. 200mm. 2.Mica heater two heat the inner sphere surface. 3.Ten thermocouple tappings in the test section. 4.Plaster of Paris / asbestos powder in the test section. 5.Panel comprises of a)Voltmeter and ammeter b)Dimmerstat c)Temperature indicatorServices required:
1.220v stabilized single-phase supply. 2.Floor surface 1m x 0.5m at working height.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Corcyra Egg Laying Cage
Description
Frame made of MDF sheet planks. Fine wire mesh provided on top and bottom fitted with 3mm dia hole wire mesh on one top, a rounded opening 3cm dia is provided which can be closed with wooden plug. On one side a rounded opening 11cm with an arrangement for drop clouser with the help of MDF sheet cover is provided for manually putting in/taking out the material. Size 35x25x18cm
Two Stage Air Compressor Test Rig
The test rig comprises of a two-stage air compressor fitted with an air tank with orifice, pressure gauges 9 an energy meter to measure the input & a Temperature indicator measures the temperatures at various points. The compressor is mounted on air receiver along with the motor, and is provided with air relief valve (safety) and a pressure switch. The unit determines volumetric efficiency and isothermal efficiency at various discharge pressures
SPECIFICATIONS:
1.Air compressor – Double cylinder, two-stage type driven by a 2-hp. Three – phase motor mounted on air receiver provided with delivery valve. 2.Air tank and orifice with water manometer for air intake measurement. 3.Pressure gauges at outlet on both stages. 4.Digital temperature indicator. 5.Energy meter to measure input power. 6.A technical manual accompanies the equipments.SERVICES REQUIRED:
1.Floor space of 2,5 X 1.5m. 2.440 V, 15A, 3ph. AC supply with neutral and earthing connection. 3.A hand tachometer.
Pinned Joint Model
SPECIFICATION:
Model consists of hinged. Model will be able to demonstrate the qualitative behavior of the truss under load. As are very flexible, a compression members will easily it`s bucking i.e. It will curve of plain. The tension member however remains straight and tight. The student will therefore have a visual picture of the type of stresses i.e. Compressive or tensile that member of truss will carry under various positive of the load. In case of pinned joint truss, the student will be able to observe that angle between members at each joint undergo a small change.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Frequency Response Analysis of Lead Lag Network
Frequency response of Lead, Lag network using P+I+D controller is a special purpose analog simulation, create using operational amplifiers. This simulator permits a detailed analysis of the first order and second order systems on the application of proportional, integral and derivative control to the improvement of their performance. The simulator may be used at high frequency for oscilloscope observation.
FEATURES:
• Built-in Function Generator (sine & square). • Self contained power supplies and power ON/OFF switch with indication. • Full mimic diagrams in the front panel. • The simulated process. - Simple Lag Process - Simple Lead Process • The simulated PID controller - Integral controller scaled in Integration time. - Derivative controller scaled in derivative action time. - Proportional band control scaled in % proportional band (PB).
Burner Bunsen-Heavy Base
Description
Comprises of heavier casted base giving the stability to the burner. Total weight of the burner is about 350 g. Nickel plated brass burner tube with rotatable air regulator & cylindrical riffled connector, mounted on casted base. Burner tube 12.5 mm dia. base 75 mm dia. connector 10 mm o.d. For use with LPG / Butane gas.
Android Based WSN Evaluation Kit
We are pleased to introduce a trainer which offers all the components (ARM 11 processor Board + GSM module + CMOS Camera + GPS module + ZigBee module +SD Wi-Fi module) of a Smart Cell Phone which works on Android OS which also Occupies 50% of the smart cell phone market. This Development Board gives you an Comprehensive solution integrating both hardware and software. These features make it easily and widely used in MID development, auto electronic devices, industrial applications, GPS systems and multimedia systems. It is good for educational training, embedded development and DIY as well.
Features
• ARM11 Samsung S3C6410, ARM1176JZF-S, up to 667MHz • 256MByte mDDR RAM and 1GByte NAND Flash • 1 x 4-wire resistor touch screen interface, • 1 x 100M Ethernet interface, • 1 x DB9 5-wire serial port • 1 x Mini USB 2.0-OTG interface and USB Host 1.1 interface, • 1 x 3.5mm audio output and on board microphone interface, • 1 x TV-OUT • 1 x SD card socket, • 1 x Infrared receiver, • 4 x TTL serial port, • 1 x CMOS camera interface, • 1 x SDIO2 interface (can be connected to SD WiFi module), • 1 x 10pin JTAG interface, • 1 x PWM buzzer, • 1 x I2C-EEPROM, • 1 x backup battery for RTC, • 1 x AD adjustable resistor, • 8 x User button and 4 x LED
Mirror, with Base
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Milling Tool Dynamometers
This is a simple and essay to understand set up introduce by sharp techno systems to study the behavior of cutting forces during milling operation in three directions. With this unit students can evaluate cutting depth, speed and feed. The unit works on standard method of octagonal ring with strain gauges. It is in to part one mechanical rings sandwiched between two M.S. plate with strain gauges fixed on it. This set of octagonal rings transmits the relevant data to the force indicator during milling operation.
FEATURES
1.Rigid construction & Compact Unit. 2.Assessment of cutting forces by giving due consideration to various parameters like depth of cut, material, cut, material, speed and feed. 3.Eassy in handling & Digital force indicators to measure three forces simuleniously.SPECIFICATIONS-
1.Mechanical sencing unit with set of octagonal rings and strain gauges. 2.Three channel digital force indicator with balancing potentiometers and polycarbonate front plate. 3.Range of force measurement in coordinate direction – 0 to 500 kg. 4.Over all size of mechanical unit- 300 x 300 mm.SERVICE REQUIRED
1.Necessary Milling Machine with automatic feed arrangement and tooling 2.230 volts, single phase, 50 Hz stabilized power supply.
Ringing Table
Pulley Rod Mounting
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Orbital Shaking Incubator cum B.O.D
Specification
Orbital shaking incubator cum B.O.D incubator is specifically designed to controlled incubation with orbital shaking arrangement with powerful geared motor for many labotatory procedures such as tissue culture, fermentations studies, enzyme reactions, growth studies etc. The outer chamber is made up of M.S sheet duly powder coated & inner chamber is made of thick S.S. sheet. The gap between wall is fitted with high grade glass wool to avoid thermal loss. The plexi glass window provided to inspect the specimen without disturbing the inner temp. The incubator is illuminated with one door operated or panel operated flurescent tube. The unit has a temp. Range from 5°C to 60°C. The temperature is controlled by Dual Display Microprocessor PID Temperature Indicator cum Controller with a accurancy of + 0.5°C. Air circulation fan is provided to maintain stability throughout. The speed of shaker is variable from 30 RPM to 250 RPM. The tray of the shaker is also made of S.S sheet with lotus type clamps to hold flasks. The unit is fitted with Digital RPM meter, 999 min digital timer.Optional Accessories
Timer 0-24 Hours. Automatic voltage stabilizer 3KVA (Most rec.).Size
16 Flasks of 500ml. 25 Flasks of 250ml. 36 Flasks of 100ml.
‘Gravity’ By Free Fall Apparatus
Consists of an electromagnet housed in a plastic moulded case with connections for an external timer, with a heavy steel sphere, and a platform unit.
For determination of 'g' (the gravitational acceleration) by free fall method.
The apparatus consists of an electromagnet which is housed in a plastic moulded case with 4 mm socket connections provided to energize the magnet and another pair of sockets for connection to a timer in use.
To perform the experiment, an electromagnet is energized and a metal sphere is attached.
As soon as the power to the electromagnet is switched off the sphere falls and the unit activates the timer.
When the sphere hits the platform, which is connected to a micro switch, the timer stops and the time of fall can be determined.
For use with compatible timer (product code LBTM).
Unit conveniently attaches to all commonly used stands (stand not supplied, see Stand & Rod Assembly - Value Pack STD-RD).
Air Conditioning Trainer General Cycle Type
The unit consists of ducting fitted with various air conditioning components. Airflow is generated by an axial flow fan and in the airflow, heaters, cooling coil and steam humidifier connection is provided. Cooling circuit consists of a hermetic compressor; air cooled condenser, thermostatic expansion valve and evaporator (i.e. cooling coil). Measurements of various parameters Torn cooling cycle and heating cycle are provided and students can easily visualize and understand the basic principles of air conditioning.
SPECIFICATIONS:
1.Cooling circuits – It consists of: a) Hermetic compressor, having the capacity of 2/3 ton of refrigeration (approx.) using R-22 refrigerant. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for high and low pressure. d) Prescott (i.e. high and low pressure cut-out). e) Thermometers for temperature measurement at various points In the cycle. f) Energymeter for compressor input measurement. g) Condensate measuring arrangement. 2.Heating Circuit – Air heaters with input control provided with energymeter for input measurement. Maximum heating capacity 1 Kw. 3.Steam generator and injector for humidification of air. All above components are connected to a duct of size 200mm. X 200mm. in which airflow is generated by axial flow fan. 4.Anemometer for measurement of air velocity, (range 0-15 m/sec. Following experiments can be conducted on the unit a) Cooling of atmospheric air. b) Heating of atmospheric air. c) Humidification of atmospheric air. d) Dehumidification and heating of atmospheric air. (Cooling coil acts as dehumidifier at reduced airflow.)SERVICES REQUIRED:
1.440 V, 15 A, 3 Phase supply with earthing connection. 2.Floor space area about 3 m. X 2 m.
Fisher Clamp
We bring to you, Fisher Clamp.
The Fisher Clamps are moulded in Polypropylene making it completely corrosion-proof.
The spring-loaded jack in the middle provides a vice like grip to the Burette and prevents it from slipping.
Two tapered wedges are provided to ensure firm grip on rods having diameter ½" or 3/8".
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Fisher Clamp- Single | 12 | |
| Fisher Clamp- Double | 6 |
