XTEMOS ELEMENT
AJAX PRODUCTS TABS
Tincture Press
Product Description
We further offer a range of Tincture Press, which is conceptualized for separation of marc of herbsand extracts made by percolation / maceration / extraction of herbs & solvents by pressing method. The unit consists of double chamber that includes a plunger pressing plate of approx. ½ inch of thickness, supposed to move inside the chamber with the support of hand operated mechanicalrotation pressing system. The unit is further attached with an outlet valve. The whole assembly is mounted on heaving M.S. base stand with M.S. / S.S. sieve for filtration purpose.Specifications
Available in Industrial Model. All the contact parts are made of St. Steel.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Kaplan Turbine Test Setup
DESCRIPTION:
Kaplan Turbine is an axial flow reaction Turbine named in honor of Dr. B. Kaplan, a Gennan Engineer. This turbine is suitable for low head. The power produced by a turbine is proportional to QH. As the head (H) decreases the J discharge (Q) must increase to produce the same power. The present Set-up consists of a scroll casing housing a runner. Water enters the turbine through the stationary guide vanes and passes through the runner axially. The runner has a hub and airfoil vanes, which are mounted on it. The water is fed to the turbine by means of Centrifugal Pump. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. A transparent hollow cylinder made of acrylic is fitted in between the draught tube and the casing for observation of flow on to the airfoil vanes. This runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of this brake arrangement so that the efficiency of the turbine can be calculated. The Set-up is supplied with control panel. A draught tube is fitted on the Outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and Vacuum Gauge are fitted at the Inlet & Outlet of the turbine to measure the total supply head on the turbine.EXPERIMENT:
1.To study the operation of a Kaplan Turbine 2.To determine the Output Power of Kaplan Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 109 (1.33 HP) | HM 109 (5 HP) | |
| Output Power | 1.33 HP / 1 Kw | 5 HP / 3.75 Kw | |
| Discharge | 1500 LPM (Approx.) | 5000 LPM (Approx.) | |
| Supply Head | 5 m | 5 m | |
| Rope Brake Dynamometer | Dia 200 mm | Dia 300 mm | |
| Sump Tank | Capacity 300 Ltrs. | Capacity 600 Ltrs. | |
| Water Circulation Centrifugal Pump | Capacity 7 HP, Three Phase | Capacity 20 HP, Three Phase | |
| Speed | 1500 RPM (approx.) | ||
| Runner | With adjustable Curved Vanes | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
Constant Mesh Gear Box Actual Cut Section
Constant Mesh Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Coplin Jar
We present to our valued clients the special range of Coplin Jars.
Our Coplin Jars are made up of polypropylene and can hold 10 sliders of the size 1" x 3" back to back.
The interior of the Coplin Jar is grooved in way to hold slides in erect position.
Domed & shallow threaded screw cap provides protection to the slides.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Coplin Jar | 12 |
Battery Hydrometer
Porous Pot
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Rear Suspension System
In this model the working of rear suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a rear suspension system are shown in actual working form. This model helps the student to understand the working of the rear suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Leaf Spring Type Suspension System With Rear Rigid Axle
(B) Rear Independent Type Suspension System
Post Office Box, Plug Type
Specific Heat Of Air Apparatus
The apparatus consists of heating element on which the air is blown. The difference in temperature of air is shown by the temperature indicator. The flow of air is measured by the orifice meter. The input to the heater is measured by voltmeter and ammeter. Thus the specific heat of air can be found out.
SPECIFICATIONS:
1.Air blower connected to FHP motor. 2.Orifice meter to measure the air flow, Heater – 1 KW heating coil placed centrally in the test section. 3.Multi channel digital temperature indicator – range 0 to 300 c. 4.Voltmeter and ammeter to measure the heat Input.SERVICES REQUIRED:
1.220 volts single phase stabilized AC Electric supply. 2.Floor space – 2 m. X 1 m. X 2 m. Height.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Earth, Neutral And Live Board Demonstration
Description
This apparatus is an effective demonstration of how the earth wire and fuse act together to protect both the user and the appliance. When the appliance is connected correctly and the LEDs in the appliance will illuminate to show the appliance is working. A fault is then demonstrated by swapping the live wire from inside the appliance to the case to show either the fuse melts (protecting the user and appliance) or in the case of no earth wire, the LEDs illuminate to indicate the passage of current through the person to ground. The fuse is easily visible and can be seen to ‘blow’ when a fault occurs.The unit is supplied with 10 m of fuse wire and full instructions. A 12 V DC power supply is required. Connections are made via 4 mm shrouded sockets.
Pin Hole Camera
Brush, Semi Micro
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Cortex M4 Development Board
Cortex M4 is an ideal replacement solution for the traditional Microcontroller & DSP Processors. Vi-S32 based on ST Microelectronics cortex M4 processor offers many features for Embedded Real Time world. The full range of hardware features on the board is provided to help you to evaluate and develop many applications. STM32 Embedded target enables systems and software Engineers to quickly deploy their application models in Matlab& Simulink to Cortex M4 ARM.
Specification
• STM32F407VGT6 microcontroller high performance 32bit ARM Cortex M4. • Operating upto 168MHz • 196Kbytes of SRAM • 2.4 MSPS Analog to Digital Converter • Two Nos. of Potentiometer interface for ADC input. • Two Nos. of DAC with simultaneous conversion • 1MB On-Chip Flash. • 4 Nos. of User LEDs, Relay Interface. • 8 way dipswitch for user input • I2C Based 2 digit 7 Segment display interface. • 4 keys keypad, Stepper Motor driver interface. • USB OTG FS with micro AB connector interface. • RTC with battery backup • I2C EEPROM device interface • SPI based temperature sensor interface • 1 Gbyte Micro SD Card interface • RS232 UART interface at a pin D connector/USB connector • CAN 2.0 lines are terminated at 9 pin D female connector • 3.2inch 240 x 320 TFT color LCD with Touch Screen • 10/100Mbps Ethernet interface • Extension header for I2C, SPI & CAN • Camera Interface
Unit Cubes
Interlinking Cubes are one of the most widely-used math manipulative in the world. The colorful, interlocking cubes help children to learn number and math concepts. These cubes represent units and link in all direction. Interlinking cubes are used for patterning, grouping, sorting, counting, numbers, addition, subtraction, multiplication, division and measurement. Each unit is a cubic centimeter measuring 1 cm x 1 cm x 1 cm
Insect Box with Stretching Strips
Description
Suitable for taking in field where the insects can be stretched on the spot and can securely be kept inside the box Teakwood frame with melamine lamination on top & MDF sheet bottom is nicely polished. Top & bottom lined with EVA sheet over which adjustable strips provided for stretching insects. Strips can be fixed at one place with fine screws and fly nuts. Fitted with brass hinges, index card holder, clips and handle. Size Approx. 43 x 30 x 11cm.
8086 Microprocessor Trainer Kit
Specification
• INTEL 8086CPU AT 4.77 MHZ CLOCK SPEED • 16KB for monitor EPROM upgradable to 64kb • 16KB RAM expandable to 64KB • Battery backup provision for RAM upto 64KB • 16 x 2 (or) 20 x 4 Alphanumeric LCD display • 101 keys IBM compatible keyboard • 24 TTL I/O lines brought out to two nos., of 26 pin FRC connector • 1 number of standard RS232C compatible serial port brought out to a pin D type male connector. • 3 channel 16 bit counter/timer using 8253. • Fully buffered address data and control signals terminated at a 50 pin header(VXT BUS) for interfacing VBMB series • of experiment boards and bus expansion. • 8 no’s of interrupt lines are terminated at a 10 pin connector. • Kit operates with a single +5V/DC supply • The kit and the power supply are mounted on a attractive light gray color fiber glass cabinet with fiber glass top cover. • Built-in line assembler & Disassembler • Powerful debugging monitor to develop user program.
Power Steering System
Power Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
