XTEMOS ELEMENT
AJAX PRODUCTS TABS
Tube Sedimentator
Digital Bomb Calorimeter
DIGITAL BOMB CALORIMETER
Bomb Calorimeter outfit provides a simple and inexpensive method for determination of heat of combustion of organic matter and the calorific value and sulphur content of solid and liquid fuel. The outfit supplied is complete for analysis as per the method recommended by British Standard Institution BS 1016. All parts of the outfit have been finished of petroleum and British Standard Institute.SUPPLIED WITH
Calorimeter Vessel with bomb support, Water jacket, Combined Lid for calorimeter vessel and water jacket, Stirrer, Connecting Leads, Connecting tube to connect bomb & pressure gauge, Connecting tube with fine adjustment valve, to connect pressure gauge, pressure gauge on stand, Spanner for oxygen tube connection, Ignition Wire, (2 meters) Nichrome, Cotton Real, stand for bomb lid, Hook for lifting bomb, stainless steel Crucible, Gelatine capsules, Gas release valve, Bomb firing unit, Vibrator, Timer, Benzonic acids. ‘O’ Ring Big, ‘O’ Ring Small, ‘O’ Ring for Stirrer Valve for Bomb, Valve Kay. Complete with Instruction manual.
Multiple Input/Output Process Trainer
Panel Features
• Power ON/OFF switch • Heater selection switch • Heater and pump indicators • High current fuse carrier for • Heater protection • Provision to run the stirrer • Digital panel meters • Two numbers of industrial PID Controller • Electrical test points are provided to measure the current signal • Mimic DiagramFeatures
• Two numbers of flow Transmitter (DPT) are provided to sense the flow of the liquid. • Three numbers of temperature transmitter (RTD) are provided at various stages to measure the temperature. • Five numbers of level sensor (RF capacitance) are provided to sense the level of each tank. • Industrial type Conductivity sensor is provided to analyze the conductivity of given Solution. • RTD sensor (or) Thermocouple acts as a temperature sensor. • Digital panel meters are provided to indicate the output of each sensor. • Provision to measure the conductivity. • Two numbers of motorized control valve or pneumatic control valve are provided to control the flow of the pipe line. • A powerful thyristor based power driver is provided to drive the heater power. • An industrial type water heater is used as a heat Source. • Storage tank of 50 litre capacity (SS). • Process tank of 15 litre capacity (SS). • Four numbers of acrylic tank are provided to study the response of four tank systems. • In necessary location Ball valve, globe valve and needle valves are provided. • Two numbers of stirrer are provided in the temperature process and alkaline process. • Three numbers of centrifugal pump (FHP) is used to circulate the water from storage tank. • Six numbers of rotameter are provided in the process inlet to visualize the real flow. • Regulated power supply is mounted in the panel. • All the flow lines are fitted by (SS) pipe fitting. • An over head tank is provided to give constant flow. • All the equipments are mounted in a rugged and mobile type metallic work station.
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
SPECIFICATIONS:
1.Shell – 150NB, 750 m.m. long provided with end boxes. a.One end box with divider plate. b.25% cut baffles – 4 Nos. in the shell. 2.Tubes – 4.5mm I.D., 6.35mm O.D.,250 m.m. length copper tubes with triangular pitch. 3.Instantaneous water heater, 3 Kw capacity, to supply hot water. 4.Thermometer for measuring the water temperature. 5.Valves to control hot and cold water flow.SERVICES REQUIRED:
1.3 P H, AC supply 2.Floor space 1.5m. X 1m, 3.230V, 15A, AC supply with earthing connection. 4.Water supply at the rate of about 10 lit/min at constant heat.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Pin Hole Camera
Hydraulic Trainer Classic
Silent Features:
1. We are manufacturing cylinders for industrial applications. Our cylinders can withstand pressure up to 160 Bar. 2. Mobile and self-contained unit, only electrical connections are required. 3. Simplicity of operation and designed for amateur use. 4. Two pressure relief valves are provided in the system. One is provided inside the tank to increase the safety. 5. Hoses can withstand pressure of 188 Bar. 6. Test Pressure : 80 Bar ; Operating Pressure : 40 Bar. 7. Realistic Industrial circuits are demonstrated. 8. Special Bell housing is provided to maintain the Run out between Pump and Motor below 0.020mm. 9. Special fixtures used for pipe bending and ferrule fitting arrangement. 10. Specially designed front mounting plate. 11. System is flushed with very high velocity (4 times the working pressure) byseparate oil which maintains class A cleanliness of system. 12. Lowest pressure drop in the system to avoid overheating. 13. Cylinder are manufactured from precision honed tubes, hardened ground, hard chrome plated piston rods and imported quality seals.
Steam Engine Model
Dicot Stem Anatomy T. S. & L. S.
Description
This model shows the transverse and longitudinal section of a dicotyledonous stem in which case the cambium ring has been formed but no secondary growth has yet taken place. Useful model for study of epidermis, lentice , cork layer, cork cambium, cortical parenchyma ,starch sheath, medullary rays, phloem, sieve plate, sieve tube, phloem parenchyma and inter fasicular cambium ,xylem, pitted vessels, bordered pitted vessels, annular vessels, spiral vessels, pith etc. Mounted on base, with key card.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Drilling Tool Dynamometers
This is a armed wheel type strain gauge drill tool dynamometer designed to measure thrust and torque during drilling operation. This Dynamometer is suitable for drilling a hole up to 25mm size in mild steel. With this Dynamometer students can study the change in these force by varying speed, cut and feed
FEATURES:
1.Rigid in construction & Sensitive transuding and amplifying system for accuracy in force measurement. 2.Compact two channel digital force indicator. 3.Use of cutting fluid during operation is possibleSCOPE OF SUPPLY:
1.Mechanical sensing unit and work piece holder with strain gauges. 2.Control panel housing digital force indicator to measure both forces simultaneously, balancing potentiometer, connoting cables. 3.Necessary switches, fuses and screen printed front plate. 4.The dynamometer is calibrated at factory with help of proving ring and readings are directly in the from of kg.
HISTOLOGY
These three sets build up to a complete study of mammalian histology.
Basic histology is covered by Histology set I.
The addition of Histology sets II and III gives a comprehensive collection of histology microslides, which should meet the needs of most advanced courses.
No teaching notes are supplied with these sets.
Health
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Comparative Terrain Model
Description
Set of 2 landform models, each includes an overlay representing ancient mountain forms that can be removed and compared with the base model to show changes millions of years later. Cross section shows basic mountain types, volcanic fault block, glaciated domes and folded mountains with lesson plan, size 45 x 60 cm.
Stop Cocks
We bring to you, polypropylene Stop Cocks.
The Stop Cocks offered by us are fitted with a PTFE plug & have serrated tubulations, that accept from 6 mm to 10 mm tubing.
The Stop Cocks are leakproof and are available in two different options i.e. 2 way & 3 way.
Material : Polypropylene/ PTFE
| Particulars | Pack (Pcs) | |
|---|---|---|
| Stop Cocks 2 Way | 6 | |
| Stop Cocks 3 Way | 6 |
Ticker Tape Timer
For the measurement of velocity and acceleration, using timing marks made on a moving paper tape by a vibrating striker.
Designed to operate on a 12V A.C. supply and uses the mains frequency as its timing standard.
The unit is housed in a moulded case including mounting flanges.
The top of the case caries a tape guide which incorporates a carbon paper disc support and an adjustable anvil for the striker point.
All moving parts are fully enclosed and a pair of 4mm sockets are provided on the side of the case for connection of the electrical supply.
Supplied with a roll of self marking paper tape.
Paper tape : 100m of paper tape, 9.5mm wide.
Carbon Paper Discs : 40mm diameter, with 3mm hole, cut from long life plastic film type carbon paper.
Worm Roller Type Steering System
Steering System – Actual Working
Manual Steering System
Type – Worm & Roller Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
FISHER CLAMP (Burette Clamp)
PRODUCT DESCRIPTION
These Clamps are moulded in Polypropylene making it completely
corrosion-proof. The spring loaded jack in themiddle provides a vice likegrip to the Burette and prevents it from slipping. Two tapered wedges areprovided to ensure firm grip on rods having dia 3/8” or 1/2”.
Available in 2types:
- Single
- double
Breeding Nest
Laboratory Spatula
Acquire from us high quality Laboratory Spatula at affordable price range.
Moulded in Polypropylene, Spatula consists of a spoon on one side while the other end is a flat construction with a knife edge.
This is helpful in breaking up crystals of different salts while the spoon is used to draw salts from the containers.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Spatula 150 mm | 12 | |
| Spatula 200 mm | 12 |
Multi Tank System
Panel Features
• Rocker switch is provided to ON/OFF the process plant. • Digital Panel Meter. • Pump Indicator. • Short Circuit protection. • Mimic diagram in the panel. • All the electrical connectors are terminated in the panel.Features
• This equipment consists of four tank system, conical tank system and spherical tank system. • Four numbers of Acrylic tank are provided for doing multivariable control of four tank system. • Conical tank (SS) is provided to performing the nonlinerar control system. • Spherical tank (SS) is provided for controlling the complex system. • Six numbers of level transmitter (DPT) are provided to measures the level of the each tank. • Three numbers of smart control valve with positioner are provided in the inlet of Flow rate. • Hand valve is provided at the bottom of the process tank to study the load disturbance. • Three numbers of hand valve are provided to control the Rotameter flow rate. • Three numbers of centrifugal pump are provided for water circulation. • Two flow transmitters are mounted for conducting flow, cascade and Ratio control. • Appropriate Digital panel meters are provided to measure the transmitter and actuator signals. • Delay coils are provided to the input of the process tanks for transportation lag study. • Storage tank of 100 litre capacity (SS). • Rotameter for Visual indication of the flow rate. • Relay circuit is provided to ON/OFF the solenoid valve. • Built in regulated power supply. • All Water flow lines are connected by (SS) fittings. • Necessary patch chords are provided for interfacing the Electrical signal. • Established successful design that mimics a real industrial process. • Front panel includes mimic diagram of the process, so students can clearly see what they are controlling. • Safe, practical and realistic. • Hand valves are provided to study the coupling (Interaction) and decouplingXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Heat Transfer In Aagitated Vessel
The unit consists of a vessel with class wool insulation ail around. A helical coil made of copper is fixed inside the vessel. A motorized agitator is fixed at the center of the coil. The vessel is provided with an electric heater and a controller is also provided for vessel. Heater heats water in the jacket while cold water is circulated through coll. Temperature of circulated water and water In vessel Is measured and thus heat transfer coefficient at various agitator speeds can be determined.
SPECIFICATIONS:
1.Vessel approx. 20 lit. capacity, provided with glass wool insulation all around and electric heater at the bottom. 2.Agitator 150 mm dia, with 1/8 HP motor to drive the agitator. 3.Helical coil – 200 dia, 8 turns, made of 3/8″ dia. copper tube. 4.Controllers for heater and agitator motor. 5.Temp. Indicator for vessel water temperature and circulated water inlet and outlet.SERVICES REQUIRED:
1.Single phase 230V, 15 A stabilized supply. 2.Water flow at the rate of 4 to 5 lit. per min. 3.Suitable drain arrangement for water. 4.Floor area -1.5 mtr. X 1 mtr. X 1 mir height.
Pulse Code Modulation/Demodulation
FEATURES:
• In-built sine wave generator • Test points to study different waveforms • In-built DC Power supplyTechnical Specifications:
• Sine wave Generator : Frequency : 1 KHz, Amplitude : 0 to 3Vpp • DC Voltage : -1.5 V to +1.5V • Clock Generator : Crystal based, 4.096MHz • Data rate : 64 kbps (for 8 KHz sampling rate)128kbps (for 16 KHz sampling rate) • ADC and DAC bits : 8 • Demodulator filter type : Butterworth low pass filter • Filter type : 6th • Filter cut-off frequency : 3.4 KHz • Mic Pre-amplifier : Transistor based • Compandingrange : -80dBm to +20dbm • Switched faults : 4 • Test points : 35 • Fuse : 30V, 100mV • DC Supply : ±5V, ±12V • System Bandwidth : 3.4 KHz
Refrigeration Trainer General Cycle Type
The unit consists of vapor compression refrigeration cycle provided with components normally used in refrigeration system so that student can get familiar with the components. Various measurement provided enable students to estimate the performance of the system.
SPECIFICATIONS:
1.Compressor- Hermetically sealed compressor, having capacity of 0.3 T. 2.Expansion Devices a) Thermostatic Expansion Valve b) Capillary tube. 3.Evaporator coil. 4.Controls: a) Services Valve b) Solenoid Valve c) Filter-Drier for refrigerant d) High/Low pressure cutout e) Thermostat. 5.Measurements: a) Thermometers (mercury in glass) – 4 Nos. b) Pressure gauges for condensing and evaporating pressure. c) Energymeter for compressor d) Voltmeter and Ammeter for compressor. e) Rotameter for liquid refrigerant flow measurement. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 1m x 2m x 2m height. 2.220V, I5Amp, Single Phase Stabilized power supply
Vertebrate Embryology Amphibia
| Ovary TS Showing Oogenesis | Testis TS Showing Spermatgenesis |
| Egg VS | Egg VS with Early Cleavage stages |
| (2, 4, 8, 16 and 32) celled stage | Egg VS Late Cleavage Stage |
| Morula VS | Early Gastrula VS |
| Gastrula VS (Yolk Plug Stage) | Neurula CS Neural Plate Stage |
| Neurula CS Neural Fold Stage | Neurula CS Neural Tube Stage Tadpole 4mm. MLS, WM |
| Tadpole 7 mm MLS | Tadpole 10mm MLS |
| Tadpole Eye Region TS | Tadpole Trunk Region TS |
| Tadpole Trunk Region TS | Tadpole External Gill Region TS |
| Tadpole Internal Gill Region TS | Tadpole Heart Region TS |
| Tadpole Head Region TS | Tadpole Tail Region TS |
