XTEMOS ELEMENT
AJAX PRODUCTS TABS
Rheostat, Single Tube
Description
A layer of oxidized resistance wire is wound on a porcelain tube which is supported by end supports. A sliding contact and three 4 mm socket terminals are provided for use as a rheostat or as a potentiometer. Other ranges also available on request.| Ohms | Ampere | Tube length | |
|---|---|---|---|
| 23 | 2.3 | 150mm | |
| 10 | 3.3 | 150mm | |
| 22 | 2.8 | 200mm | |
| 24 | 3.3 | 250mm | |
| 28 | 4.2 | 400mm |
Cyclone IV FPGA Controller
FEATURES:
• Based on Altera family Cyclone IV, Device : EP4CE30 • One 34 pin header used for IPM Interface. - 16 PWM output - 8 capture inputs. • One 26 pin header ADC. - 4 channel 1MSPS ADC. - Total 8 channel using 2 Nos of ADC. - 12 bit resolution. - Input range -10V to 10V / -5V to 5V. • One 5 pin phoenix connector DAC - 4 channel DAC, 12 bit resolution. - Output range -10V to 10V / -5V to 5V. • 8 output Light Emitting Diodes (LEDs). • 8 input slide Switches. • 4 user push button switches. • 2-user limit switch. • 20 x 4 Alphanumeric LCD display. • On Board Isolated JTAG Programmer Compatible with QuartusII software. • Isolated USB (USB to Serial) interface. • 3 Nos of 20 pin header each have 16 IOs.
Unsymmetrical Bending Apparatus
DESCRIPTION:
Apparatus consist of an angle of size 1” x 1” x 1/8” or in equivalent metric units of length 80cm is tied as a cantilever beam. The beam is fixed at one end such that the rotation of 450 intervals can be given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement is provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end. A dial gauge with magnetic base is supplied with the apparatus.EXPERIMENT MANUAL:
• To study the behavior of a cantilever beam under symmetrical and unsymmetrical bending. • Using a Dial gauge shown a increasing and decreasing of heights.
Refrigeration Test Rig
Features
• 5 Nos of thermocouples are provided to measure the temperature at different points. • One multi channel temperature indicator is provided to display the temperature • One capillary tube and one thermo expansion valve is provided to check the performance separately. • Compressor supplies refrigerant through evaporator to find out cooling effect • 4 Nos. of Pressure Gauges are provided to measure the pressure at various point • One Energy meter is proivded to measure the overall power consumption • One voltmeter is provided to display the voltage. • One ammeter is provided to display the current.Specification
• Compressor :Hermatic • Capacity : 1/4 Ton • Supply : 230 V AC / 50 Hz • Condensor : 12 Coil • Evaporator : 15 Liter Capacity • Refrigerant : R134AXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Direction of Current
Rocks Collection
Description
A comprehensive collection of igneous , metamorphic and sedimentary rocks, in wooden box with partitioned tray containing 50 specimens, each nominally numbered and enclosed in a transparent plastics bag. Specimens may be removed from bags for detailed examination. Each specimen is labelled also on the inside of the box lid, indicating the geological name.
Electromagnetic Field Demonstrator
Description
This apparatus demonstrates the magnetic field patterns associated with the different shapes of current carrying conductors. Comprises three conductors, each of different shape/configuration – straight rectangular, circular loop and solenoid all mounted on a plastic base. Each configuration is provided with a pair of 4 mm sockets to connect them to a low voltage DC power source, with output current not exceeding 5A With the included iron filings and 8 magnetic compasses, you can investigate the associated field and flux patterns.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Post Office Box, Wheatstone Bridge
Description
With two ratio dials of 10,100 and 1000 ohms each and a resistance arm of four dials, each of ten coils of 1, 10, 100 and 1000 ohms, giving total resistance of 11,110 ohms with 4 mm socket terminals for battery, galvanometer and unknown resistance. Highly stable resistances are used. Accuracy ±0.1%
CNC Mill Trainer
CONTROLLER:
SIEMENS 802D Main Spindle Drive : D.C. Thyristor Drive, Inbuilt Safety, 1.5 HP X, Y and Z Drives : SIEMENS Servo Motors and Drives Input to Stepper : Optically lsolated Motor Drive TTL compatible Interpolation : Linear, Circular parabolic Interpolation, Slot / Pocket Milling Code Used : G, M, S, T, F, I, K, M, F, Cycles : Circular Interpolation, Mirror, Pocket Milling Cycle Pocket & Helical Milling : Provided with Std CodesTABLE:
Length x Width : 450 x 175 (approx.) Clamping Area : 350 x 175 (approx.) T Slots : 10mm slot widthMACHINE DETAILS:
Resolution : 5 micron Tool Change : Automatic, 8 station Rapid Travel : 5000mm/min Weight in kg : 750kg Dimension in mm : 850 x 850 x 1550 mm Automatic Lubrication : Provided Repeatability : 10 micronSPINDLE:
Spindle Speed : Continuous Variable Spindle power : 1.5 HP Inside Taper : ISO 30 Speed Range : 100 to 4000 RPMAXIS TRAVEL
Longitudinal Traverse : 250mm Cross Traverse : 175mm Vertical Traverse : 250mm
Breast Examination Model
Description
Demonstrate realistic self-examination with our natural casting of a female upper body with medium sized breasts. It can easily be worn, in order to better train and practice breast self-examination. Made of high-quality silicone. Displays the skin in finest detail. Very realistic to the touch and dermatologic ally tested Breast examination is possible in both upright and lying positions.Benign and malignant tumors in different stages of development hone self-examination skills:
2 benign tumors 4 malignant tumors 2 typical anomalies Includes “Female Breast” chart Supplied with talcum powder, harness, stand and aluminum carrying case.
Lathe Tool Dynamometers
This is a strain gauge type two component lathe tool dynamometer designed to measure vertical and horizontal forces on the while orthogonal cutting process. The unit is in two parts one is mechanical sensing unit or tool holder, which can mounted on the top of the Ross slide after removing swivel base and compound slide of a lathe and digital force indicator. With this Dynamometer student can study the change in these forces by varying Speed, Cut and Feed.
FEATURES:
1.Rigid in construction 2.Sensitive transuding and amplifying system for accuracy in force measurement. 3.Compact Digital force indicator. 4.Use of cutting fluid during operation is possible.SCOPE OF SUPPLY:
1.Mechanical sensing unit or Tool Holder with string gauges. With H.S.S. tool of ½ “ size. 2.Control panel housing digital force indicator to measure two forces simuletensiously, balancing potentiometers, connoting cable. 3.Necessary switches, fuses and polycarbonate front plate. Range o to 500 Kg. 4.Centre Height, P.C.D.of clamping bolt size, clamping Bolt size. Three component lathe tool dynometer is also available.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Beaker (TPX)
The company is primarily engaged in the exporting and trading of the latest Beaker (TPX) all across the globe.
The demand for our Beaker (TPX) has gradually increased over the time span, for their various attributes, and premium quality.
Our Beaker (TPX) are available in different specification and at affordable prices.
Artery model showing plaque building
Dicot & Monocot Root
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Dicot Plant Stem
Tuning Fork Activator
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Lagged Pipe Apparatus
Lagged Pipe Apparatus:
The apparatus consists of three concentric pipes mounted on suitable stand. The space between innermost and the middle pipe is fifed with a lagging material and the space between the middle and the outer most is filled with and other lagging material. The lagged pipe is heated with a cartridge heater inserted at the axle length of the pipe. Voltmeter and ammeter on the panel can measure the input to the heater. The intermediate temperatures can be measured by the thermocouples attached at the surfaces of the pipe. Thus the resultant conductivity of the materials can be found out.
SPECIFICATIONS:
1.Pipes : a)Gl pipe (innermost) – 6 cm. (Outer Diameter). b) Gl Pipe (Middle) – 8.5 cm. (Mean Diameter) c)G! Pipe (Outermost) – 10.7 cm. (inner Diameter) d)Length of pipes 1 Meter. 2.Heater : Nichrome wire cartridge heater placed centrally, of suitable capacity. 3.Control Panel : a)Single Phase Dimmerstat – 1 No. b)Voltmeter (0 – 250V) – 1 No. c)Ammeter (0- 2A) – 1 No. 4.Temperature Indicator : Multichannel Digital Temperature Indicator ranging (0 – 300 C) using Cr/AI ThermocouplesServices Required:
1. A.C. Single Phase 230 V electric supply 2. Floor Area-1.5 Meter X 1 Meter X 0.5 Meter High
Multi-Functional Nursing Simulator (Female)
Description
Designed according to the demand of the clinical principles and the guidelines of nursing training. This multifunctional simulator could simulate an actual circumstance for practice. Multiple functions, rural practice, easy assembly, well shaped appearance and correct anatomical landmarks provides a very good training for practice.Features:
Head Care. Body care. Patient moving. Different lying pose. Bilateral and Unilateral oxygen inhalation. Atomization inhalation therapy. Nasal Feeding. Gastric lavage training. Intravenous Injection. Intramuscular Injection. Hypodermic Injection. Various fistula orifice washing practice. Female Catheterization. Female Bladder Washing. Enema Treatment. Simulator Assembly.
Cam Analysis Apparatus
The apparatus is designed to study the cam profiles and performance of cam and follower system. The apparatus consists of a shaft supported by ball bearings upon which three different types of cams can be mounted.
The push rod for follower is supported vertically, which can adopt three different types of followers. Cams and followers can be changed easily. A variable speed motor rotates the cam. A dial gauge permits plotting of follower displacement with respect to cam position. By operating the system at different Speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. Jump can be visualized also with the help of stroboscope (it is not supplied With the product).
