XTEMOS ELEMENT
AJAX PRODUCTS TABS
Outside Micrometers (Etching Marking)
Description
Micrometer is used to measure short lengths accurately Technical Details : ; Carbide Tipped Measuring Faces ; Blue Metallic Finish Frame ; With Locking Clamp and ratchet stop ; Printed Marking on the Vernier Scale ; Least Count : 0.01mm/0.001” Sizes Sizes 0-25 0-1” 25-50 1-2” 50-75 2-3” 75-100 3-4” 100-125 ; 125-150 ; 150-175 ; 175-200 ; Specifications: Guarantee ; 6 Months without abuse Packing ; Plastic Box Calibration ; In house.Human Torso With Interchangeable Sex Organs
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Two Stroke Diesel Engine Model
Thermocouple, Single
Underground Mine Model
Seven Segment LED Display Circuit
A common anode seven segment module is fitted on a board with 8 bit dip switch to control the each segment of seven segment LED display. The inputs A-D of a display driver are connected to the binary coded decimal (BCD) outputs from a decade counter. A network of logic gates inside the display driver makes its outputs a-g become high or low as appropriate to light the required segments a-g of a seven segment display. A resistor is required in series with each segment to protect the LEDs
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Thermocouple, Double
Fertilization Process Simulator
Battery Hydrometer
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Model of Galilean Telescope
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Ticker Tape Timer 12V
Ticker Tape Timer 12V
These devices use an electromagnet which activates a striker, producing dots via a carbon disk on the ticker tape.
With 4mm terminal sockets.
The dots are produced at a rate of 50 - 60Hz depending on the mains frequency.
There are 6V and 12v units available.
The Ticker Tape Timers are used in the measurement of velocity, acceleration and general timing.
Smart Grid Simulator
Smart Grid Simulator (VPST - SGS - 01) is a convenient solution for studying the basic Architecture and the Real-Time Operation of Smart Grid, Which consists of i) 8 types of Generation ii) Transmission Line iii) Six types of loads iv) Communication through LCD and PC.
Specification
• Six different generating station (Up to 10 MW) - Wind, Solar, Diesel, Bio-Gas, Fuel-Cell &UtilityGrid. • Two separate Transmission Lines (5MW Each) – TL-1, TL-2. • Six different power consumers (Up to 10 MW)– Gen.Industry, Emergency, Urban Area, Rural Area, Cement, Chemical Industry. • Six analog pot-meters for the power consumption control. • Graphics LCD & Keypad based configuration & monitoring of smart grid. • On board LCD & PC based GUI for easy understanding of the smart grid operation. • Automatic Smart Grid Control algorithm implemented for transmission line control, over current relay & automatic load sharing/adjustment in case of over loading.4 Stroke 1 Cylinder Petrol Engine Manual Driven
The engine will be sectioned to show the internal constructional details. The working of individual part and accessories like Valves, Pistons, pumps, Crank and Camshaft, etc. will be demonstrated. It is provided with Flywheel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes. The actual cut section engine will be supplied with key card & very interesting literature regarding working.
CNC Mill Trainer
CONTROLLER:
SIEMENS 802D Main Spindle Drive : D.C. Thyristor Drive, Inbuilt Safety, 1.5 HP X, Y and Z Drives : SIEMENS Servo Motors and Drives Input to Stepper : Optically lsolated Motor Drive TTL compatible Interpolation : Linear, Circular parabolic Interpolation, Slot / Pocket Milling Code Used : G, M, S, T, F, I, K, M, F, Cycles : Circular Interpolation, Mirror, Pocket Milling Cycle Pocket & Helical Milling : Provided with Std CodesTABLE:
Length x Width : 450 x 175 (approx.) Clamping Area : 350 x 175 (approx.) T Slots : 10mm slot widthMACHINE DETAILS:
Resolution : 5 micron Tool Change : Automatic, 8 station Rapid Travel : 5000mm/min Weight in kg : 750kg Dimension in mm : 850 x 850 x 1550 mm Automatic Lubrication : Provided Repeatability : 10 micronSPINDLE:
Spindle Speed : Continuous Variable Spindle power : 1.5 HP Inside Taper : ISO 30 Speed Range : 100 to 4000 RPMAXIS TRAVEL
Longitudinal Traverse : 250mm Cross Traverse : 175mm Vertical Traverse : 250mmXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
















