XTEMOS ELEMENT
AJAX PRODUCTS TABS
Photo Gates & Leads
These pair of photo gates is housed in tough moulded cases giving them excellent durability.
The lamps operate on 6 Volts with a special built in circuitry which prevents lamps from damage in case higher voltage is applied accidently.
The photo gates can be connected by 4 mm. sockets to a timer and power supplies.
Single Phase Cyclo Converter
Specification
• Consists of firing circuit, SCR power circuit and load. • Line synchronized IC based linear firing circuit. • Line synchronization achieved by step - down transformer. • Four nos. firing pulse with pulse transformer isolation to trigger four SCR. • One no. potentiometer used to vary the firing angle (180° - 0°). • Carrier logic implemented with carrier frequency of 4KHz. • One no. toggle switch with debounceogic for pulse ON/OFF. • EPROM Based firing pulse frequency variation. • Two nos. toggle switch to select different frequency (Hz, 50/2Hz, 50/3Hz, 50/4Hz). • Power circuit consists of Four nos. SCR with fuse protection. • Anode, Cathode, Gate terminals are terminated in the front panel for user connection. • 24V AC, 1Amp Provided for power circuit input with ON/OFF switch. • One no. fixed R, load provided Center tapped inductor for power circuit. • 230V, 50Hz AC input with ON/OFF rocker switch, fuse for over load.Half lower Jaw
Coil Ignition System Of An Automobile
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE

IoT Development System
The industrial networks are primarly concerned with Programmable Logic Controllers(PLC),Distributed Control Systems(DCS), Supervisory Control and Data Acquistion Systems(SCADA) any many other hetrogenous devices in the form of differnt applications. More over these devices are based on either wired or wireless communication protocols like Profinet, Profibus, MODbus, WiFi, Zigbee and Etc.
Specification:
• To impart the knowledge about Industrial IoTa the Students, We have designed a IIOT trainer kit, which have inter-quark chip based IoT Gateway. • This Gateway is a universal Gateway supports many different types of communication protocols such as wired and Wireless communication for industrial applications. • The IIoT Gateway connected with Siemens based Distributed Control System(DCS), Programmable Logic Controller(S7-1200, S7-1500) using S7-protocol and OPC UA. • The Intel centrino based powerful WiFi chip enables us to the access data via Mobile Application. • The Gateway can get the internet connectivity via Ethernet and WiFi also. • This Gateway can communicate with our own ingenious data acquisition system using RS485 BUS and RS232 Bus. • The USB based communication exchange the data between Zigbee co-coordinator and Gateway.Resistance Units, Interlocking
Fiber Optics Communication Set
Objective:
To construct an optical transmitter and transmission of signal through Fiber Optics Cable. To construct an Optical Receiver and study the Attenuation of Signal when transmitted from Transmitter to Receiver end. Analog and Digital link can also be studied as this unit is complete with Sine and Square Waves. Bending losses can also be studied.
Features:
Instrument comprises of Microphone Preamplifier stages consists of MIC (Microphone), Preamplifier and Amplifier (Voice is converted to electrical signal and then amplified) and fed to LED (Transmitter) and then through fibre cable, signal is sent to Photodetector (Transistor) and again amplifier and output is sent to Speaker Unit. Power Supply of +6 VDC is used in Amplifier ckt. 2 No. Fiber Optics cables are provided (one of them is 50 cm long and the other is 100 cm long). One more fiber cable of 50mm length having connector at one end is also provided. Connectors a both end of fiber cable are provided for insertion in sockets provided on the front panel. Bending losses can also be studied in long wire.
Standard: MIC with 2 meter long lead and a Speaker 4, 4 ohm are mounted in a vertical box.
Accuracy: with 1 meter long connecting leads. 2 No. Fiber optic cable having length of 50 cm and 100 cm are provided.
Optional : Digital multimeter (3 1/2 Digit, Big size Display) This model also include Digital Multimeter and wooden frame for measurement of Numerical aperture i.e. complete in all respect including facility for measurement of numerical aperture.
CNC Lathe Trainer With Servo Drives
CONTROLLER:
(1) Type of control system: PLC based system (2) Main Spindle Drive : AC Motor with VFD (3) Z and X Drives : Stepper drive with RAMP function (4) Input to Stepper Motor : Optically Isolated (5) Motor Drive :TTL Compatible (6) Run Speed Control : Computer controlled through software (7) Interpolation : Liner / Circular / Parabolic (8) Cycles Used :G,M,S,T,F,I,K,M,F (9) Cycles : Circular Interpolation / Canned (10) Threading : Straight / Taper (11) Power Devices : Short Circuits and over Temperature Protected (12) Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
(1) Center height : 100mm (2) Swing over Carriage : 80mm (3) Distance between Centre : 250mm (4) Longitudinal Travel : 250mm (5) Weight : 350 kg (6) Dimension in mm : 1100 x 750 x 1700 (7) Rapid Travel : 500mm/min (8) Resolution X & Z Axis : 10micron (9) Dt. Motor Power : 40V – 4A (10) Lubrication : ManualSPINDLE:
(1) Spindle Speed : Continuous Variable (2) Spindle Power : 2 HP (3) Inside Taper : MT3 (4) Speed Range : 50 to 3000RPMXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Insect Showcase Cabinet (Small)
Description
For keeping insect storage & display showcase of Size 45 x 30 x 6.5 cm (RI-62-02). Cabinet frame of plyboard with melamine lamination. Hinged door is provided with lock and handle and is lined with velvet. Insect Showcase Cabinet (Small) with 6 Show cases Insect Showcase Cabinet (Small) with 12 Show cases Insect Showcase Cabinet (Small) with 24 Show casesPipette Pump
fast release Pipette Pump for precise pipetting & zip quick emptying.
The Knurled thumb wheel can be rotated to draw up or dispense liquids while the releaser may be pushed in for zip-quick emptying.
The moulded chuck has silicon rubber coller inside to hold various pipettes of standard sizes.
The Pipette Pump resists acids & alkalis and can be easily disassembled for thorough cleaning.
Material : Acrylonitrile Butadiene Styrene
Particulars | Pack (Pcs) | |
---|---|---|
Pipette Pump 2 ml | 12 | |
Pipette Pump 10 ml | 12 | |
Pipette Pump 25 ml | 12 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION

Expansion Model of Human Teeth
Magnetic Kit
Description
A kit of magnets and accessories in a storage tray.Contents :
1. One Horseshoe magnet, 100 mm, with keepers.Two ceramic bar magnets, 75 mm long. 2. Three ceramic ring magnets, 38 mm diameter 3. Two plotting compasses clear both sides, 19 mm diameter 4. One lodestone specimen. 5. One pack Iron Filing. 6. One each strip of Iron, Aluminium, Zinc and Copper metal.Water Table Model
Shunt Active Filter Trainer
Specification
• FPGA Spartan 3A DSP board used for generating the PWM signals. • Three phase 3 level diode clamped inverter used as a Active filter. • SRF (or) Instantaneous PQ theory will be used to generating reference current. • PI control or fuzzy logic will be used to regulate the dc link capacitor voltage. • Reference DC link Voltage will be 250V. • Hall effect current transducers used to sense the source currents, load currents and compensation currents. • Hall effect voltage transducers used to sense the dc link voltage and source voltages. • Necessary source inductor and filter inductor provided. • Input source Line voltage -200V (Peak). • Input source Current -10A (Peak). • Power Rating -3KW. • Reactive power compensation can be provided. • 3KW linear and non-linear loads will be given. • User can modify source, filter inductance and external loads. • User can modify control algorithm. • Industrial type cabinet provided. • Before compensation source current THD will be greater than 26% • After compensation source current THD - 2.5 - 4% in 3 level inverter - 4 - 5% in 2 level inverterXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Primary and Secondary Coil
Description
The apparatus demonstrates the principle of Electromagnetic Induction and helps explain the concept of a transformer. Primary and Secondary coil consist of coils mounted on plastic spools, with 2 binding posts on each coil. You can slide the primary coil inside the secondary coil. Also includes a soft iron core for induction experiments. Primary coil has 480 turns while secondary coil has 3800 turns. Requires a galvanometer and bar magnets, not supplied with apparatus.Band & Block Brake
Earthy Minerals Collection
Low Voltage Coils, For Demountable Transformer
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT