XTEMOS ELEMENT
AJAX PRODUCTS TABS
Micro Controller Development Board
Microcontroller development board is designed to train engineers about the structural design, instructions and utilize the 8051 microcontroller board. A 40 pin ZIF socket for easy insertion of 89 series microcontroller with four 10 Pin FRC connectors is provided on the board. Outputs from I/O port from microcontroller are available on FRC connectors those can be easily connect with different modules. Microcontroller Development Board consists of EEPROM with 4K memory changeable with more RTC DS1307 with 32 KHz crystal with battery backup One 12 V stepper motor with drivers.One 16 x 2 LCD display. 8 Output LED indicators. 4 multiplexed 7-segment display. 8 single bit toggle switch. 4 x 4 matrix keyboard. Single Channel ADC with potentiometer and provision of external inputs RS 232 serial communication. One 12 V DC motor driver.
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Platinum Resistance Thermometer
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Thermal Conductivity Of Liquid
Thermal conductivity of is an important engineering property. The apparatus uses guarded hot plate method for determining thermal conductivity. It consists of hot plate i.e. an electrical heater sandwiched between two plates. The heat loss from hot plate is prevented by using two guard heaters and heat of removes heat from liquid by circulation of water. Input to heaters the temperatures.
SPECIFICATIONS:
1.Guarded hot plate assembly comprising of main heater, ring guard heater and top guard heater, mounted over the liquid test cavity. 2.Cold plate assembly provided with water connections. 3.The assembly is housed in an enclosure box with glass wool insulation. 4.Instruments panel consisting of : a).Digital voltmeter and ammeter of suitable range. b).Dimmerstat for controlling input to the heaters (2 amp. 3 Nos.) c).Multichannel digital temperature indicator.SERVICES REQUIRED:
1.Floor space of about 0.75m. x 1.5m. at working height. 2.230v. AC electrical supply with earthling connection. 3.Water flow rate of about 10- 15 lit/min. at constant head.
Diffraction Object Holder
Advanced Multi-functional Child Nursing Manikin
Description
Designed according to the anatomical characteristics of child, and specializing in child care training. Applying imported materials, the skin is soft and flexible, not easily deformed, realistic shape, lovely appearance, and clear internal anatomical structure. Good helper for pediatric nursing teaching and training.Features:
Pupil observation,Bilateral Pupil states: normal, mydriasis. Operations of child care: full body bandage exercise, bathing, changing clothes, hair combing, eye washing and administering, otic drops and irrigation, mouth cavity care, blood collection of finger and TBtest. Airway management: realistic mouth, nose, tongue, gum, pharynx, larynx, esophagus, epiglottis, trachea and tracheal ring, can practice tracheal intubation, sputum suction, oxygen inhaling. Oral and nasal feeding. Gastro lavage. Venipuncture, injection, transfusion (Arm). There is an obvious feeling when needle penetrates into vein. And blood flash back indicates proper insertion. Intramuscular injection in bilateral deltoid, bilateral vastus lateralis and bilateral buttock. Enema, placement of rectal suppository. Urethral catheterization. Holistic care: sponge bath, replacing clothes, cold and heat therapy. Limbs joints: Bend, rotation, upper and lower movement. Bathing and bandaging activity. Ostomy nursing of ileum, colon and bladder. Tibial bone marrow puncture: simulate the process of bone marrow puncture, obvious body surface symbol. Simulated bone marrow would outflow in the case of correct puncture.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
BEAKER TONG
Friction In Pile Lines Apparatus
DESCRIPTION:-
The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the losses due to fiction in pipes Ø To determine the friction factor for Darcy Weis back equationUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pipes (2 Nos.) : Material GI of ½ “ & 1” Diameter Ø Pipe Test Section : Length 1 m Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 25 Ltrs. Ø Sump Tank : Stainless Steel, Capacity 50 Ltrs. Ø Stop Watch : Mechanical / Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted Structure
Westminister Electromagnetic Kit
Description
A very effective and motivating learning aid in elementary electromagnetism. Consists of 8 anisotropic alloy magnets, 8 ceramic ferrite magnets, 4 steel magnet yokes, 6 plotting compasses, 4 hardboard formers to take compasses, 1 bottle iron filings 250 gm, 4 dispensers for iron filings , 4 double C-cores, 4 clips for C cores, 4 Aluminium rings, 4 Aluminium split rings, 4 armatures with axle tubes, 4 Aluminium axle rods, 8 split pins, 16 rivets, 4 formers for coils, 4 reels cello tape, 4 reels copper wire, 4 sheets white pasteboard, 4 plain postcards, 4 reels white cotton thread, 1 length latex rubber tubing, 4 each resistors 100 ohms and 10 ohms, 4 support bases, 10 MES bulbs, 8 MES bulb holders,1 wood clamp and 1 wooden block. With instructions.
Human Teeth With Tongue
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
HISTOLOGY
These three sets build up to a complete study of mammalian histology.
Basic histology is covered by Histology set I.
The addition of Histology sets II and III gives a comprehensive collection of histology microslides, which should meet the needs of most advanced courses.
No teaching notes are supplied with these sets.
Mechanical Training Model
Description
Highly useful for demonstrating the most fundamental and frequently used mechanism. Very useful for engineering students. All the components are made of high degree of precision. These modules are assembled on transparent perspex sheets to facilitate teaching. Easy to assemble or disassemble.
Brown Plant Hopper Insect Rearing Cage
Description
Framework of seasoned teakwood, nicely polished. Front door and top provided with non rattling glass and back & two sides with nylon wire screen supported by fine wire mesh. Wooden base covered with laminated sheet from inside. Size: 45x45x55 cm. Brown Plant Hopper Insect Rearing Cage Size: 60x60x80 cm.
Water Turbine with Dynamo
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
AED Trainer
Description
The Laerdal AED Trainer 2 offers an affordable alternative for educating the layperson and healthcare provider in the effective use of an automated external defibrillator.Product benefits:
Educationally effective, offers all the essential features necessary for learning appropriate AED use and techniques. Affordable training through the simulation of the HeartStart FR2 AED in appearance and operation. Added instructor flexibility through unique control of the scenario selection by use of the remote control device. Flexible configuration of the device through a scenario builder program that allows the additional creation of custom training scenarios. Cost-effective operation through use of six C-cell batteries.Product features:
Ten pre-configured sudden cardiac arrest scenarios compatible with training programs developed by internationally recognized responder programs. Remote control (optional) for manual scenario selection pause/resume function, AED Trainer 2 volume control, motion artefact, low battery or replace battery, loose electrodes connection, shock able or non-shock able rhythms and error conditions that simulate the red X in the Heart Start FR2’s status display window. Designed for use with the AED Little Anne® and AED Resusci Anne® manikins with Laerdal LINK Technology by providing student feedback as to proper pad placement on the manikins. It can also be used with any other manikin where Laerdal Link Technology is not available. Proper pad placement required in order for the trainer to advance in the scenarios when used with the AED Little Anne or AED Resusci Anne manikins.
Tuning Forks Set
CPR Training Manikins(torso)
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Tablet Hardness Tester (Pfizer Type)
Product Description
A handy, tough and direct dial reading type tablet hardness tester, working as pair of plairs, generates breaking force in single grip. The instrument offers accurate and reproducible results much faster other conventional hardness testers.Specifications
Accuracy : ±0.2 Kg Least Count: 0.2 Kg Safe Testing Force: 20 Kg Maximum Tablet Diameter: 25mm
Ruhmkorff Coil
Description
Ruhmkorff Coil produces pulses of high voltage spark from low voltage DC source (6 – 12 V DC). It is suitable for use with gas-filled discharge tubes, vacuum tubes, eudiometers and for general laboratory work. Includes an adjustable vibrator system, primary current polarity reversal, on-off switch, a capacitor enclosed in the box and special alloy contacts. Spark gap at the discharge points can be adjusted by sliding rods back and forth. Spark Length 15 mm.
Lathe Tool Dynamometers
This is a strain gauge type two component lathe tool dynamometer designed to measure vertical and horizontal forces on the while orthogonal cutting process. The unit is in two parts one is mechanical sensing unit or tool holder, which can mounted on the top of the Ross slide after removing swivel base and compound slide of a lathe and digital force indicator. With this Dynamometer student can study the change in these forces by varying Speed, Cut and Feed.
FEATURES:
1.Rigid in construction 2.Sensitive transuding and amplifying system for accuracy in force measurement. 3.Compact Digital force indicator. 4.Use of cutting fluid during operation is possible.SCOPE OF SUPPLY:
1.Mechanical sensing unit or Tool Holder with string gauges. With H.S.S. tool of ½ “ size. 2.Control panel housing digital force indicator to measure two forces simuletensiously, balancing potentiometers, connoting cable. 3.Necessary switches, fuses and polycarbonate front plate. Range o to 500 Kg. 4.Centre Height, P.C.D.of clamping bolt size, clamping Bolt size. Three component lathe tool dynometer is also available.
Tilt Telescopic Collapsible Steering System
Tilt, Telescopic & Collapsible Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
