XTEMOS ELEMENT
AJAX PRODUCTS TABS
Crucible Support Stand
Photo Gates & Leads
These pair of photo gates is housed in tough moulded cases giving them excellent durability.
The lamps operate on 6 Volts with a special built in circuitry which prevents lamps from damage in case higher voltage is applied accidently.
The photo gates can be connected by 4 mm. sockets to a timer and power supplies.
Insect Cage
Description
Aluminium angle framework supported on wooden batons. Fine mesh provided on slide and top. Hinged door provided on side or top. Hinged door provided with clips for tight closing. Wooden bottom covered with sunmica from inside. Size 15x15x15cm. Size 20x15x15cm. Size 25x20x20cm. Size 20x20x20cm.Folding Type
Size 30x30x45cm.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Cyclone IV FPGA Controller
FEATURES:
• Based on Altera family Cyclone IV, Device : EP4CE30 • One 34 pin header used for IPM Interface. - 16 PWM output - 8 capture inputs. • One 26 pin header ADC. - 4 channel 1MSPS ADC. - Total 8 channel using 2 Nos of ADC. - 12 bit resolution. - Input range -10V to 10V / -5V to 5V. • One 5 pin phoenix connector DAC - 4 channel DAC, 12 bit resolution. - Output range -10V to 10V / -5V to 5V. • 8 output Light Emitting Diodes (LEDs). • 8 input slide Switches. • 4 user push button switches. • 2-user limit switch. • 20 x 4 Alphanumeric LCD display. • On Board Isolated JTAG Programmer Compatible with QuartusII software. • Isolated USB (USB to Serial) interface. • 3 Nos of 20 pin header each have 16 IOs.
Moving Coil Meters
Description
Meters are designed for D.C. measurements to meet every need of schools, colleges and technical institutions. All meters are housed in moulded dust proof cases with zero-adjuster and have connections terminals. Type MO-65 Round.| Case | : | ABS Plastic | |
| Accuracy | : | Class 2.5 | |
| Scale length | : | 50 mm. | |
| Overall size | : | 100x90x90 mm. approx. |
Silicone Diode Unit
Post Office Box, Wheatstone Bridge
Description
With two ratio dials of 10,100 and 1000 ohms each and a resistance arm of four dials, each of ten coils of 1, 10, 100 and 1000 ohms, giving total resistance of 11,110 ohms with 4 mm socket terminals for battery, galvanometer and unknown resistance. Highly stable resistances are used. Accuracy ±0.1%XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
CONDENSER CLAMP
PRODUCT DESCRIPTION
- Three finger condenser extension clamp with Bose head.
- Aluminum stem the overall length of the clamp is 10.0.
- The extension rod contributing 6 the rubber coated jaws will open to 3.5 and will provide a six point contact for a firm
- The boss head right angle clamp will accept rods up to.63 /16 mm.
- 3 Finger Aluminium Condenser Clamp (Rubber Lined)
- 4 Finger Aluminium Condenser Clamp (Cork Lined)
- 3 Finger Brass C.P. Condenser Clamp (Cork Lined)
- 4 Finger Brass C.P. Condenser Clamp (Cork Lined)
Magnifier, Folding
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Human Digestive System
U Shaped Magnet
Human Eye, 5 Times Enlarged
Description
A highly improved and enlarged model showing fine details in three dimensional relief. Cut in horizontal plane and separable in seven parts. After removing the upper half of the sclera (outer shell). The choroid with its verticose veins is exposed with the removal of second shell, details of the retina come into view and the position of the yellow and blind spots is quite visible. All important anatomical features such as muscle insertions, optic nerve, blood vessels, ciliary body, cornea, crystalline lens, and iris etc are clearly numbered and are identifiable. Mounted on base with key card.
Outside Micrometers With Micron Reading
Description
Micrometer is used to measure short lengths accurately Technical Details : Least Count : 0.001mm Carbide Tipped Measuring Faces Blue Metallic Finish Frame With Locking Clamp and ratchet stop Etching Marking on the Vernier Scale ; Sizes Least Count in mm 0-25 0.001mm 25-50 0.001mm 50-75 0.001mm 75-100 0.001mm Guarantee 6 Months without abuse Packing Plastic Box Calibration In house.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Rear Axial Assembly With Differential Gear Semi
Rear Axial Assembly With Differential Gear Semi Floating Type – Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Dissecting Trays
Stacking Counters
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Venturimeter Orificemeter Calibration Set Up
DESCRIPTION:-
The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different floe rate. Flow rate of water is measured with the help of measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the Co-efficient of discharged through Venturimeter and Orificemeter Ø To measure discharge through Venturimeter and Orificemeter as flow meters.UTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATIONS: –
Ø Venturimeter : Material Clear Acrylic, Compatible to 1” Dia pipe Ø Orificemeter : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Polarising Filter Stress Determination
Description
Demonstrate stress patterns in solids with this new and valuable equipment. Two polarising filters, mounted on a graduated frame are placed on a plastic base. Clear acrylic pieces of different shapes are introduced between the filters; when pressure is applied to the solids the resulting stress patterns are observed. An important method of demonstrating polarisation and stress. Includes instructions.
Cam Analysis Apparatus
The apparatus is designed to study the cam profiles and performance of cam and follower system. The apparatus consists of a shaft supported by ball bearings upon which three different types of cams can be mounted.
The push rod for follower is supported vertically, which can adopt three different types of followers. Cams and followers can be changed easily. A variable speed motor rotates the cam. A dial gauge permits plotting of follower displacement with respect to cam position. By operating the system at different Speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. Jump can be visualized also with the help of stroboscope (it is not supplied With the product).
SPECIFICATIONS OF CAM ANALYSIS APPARATUS:
1.Cam -Eccentric, tangent and circular ARC type – one each. 2.Follower- mushroom, flat faced and roller type – one each. 3.Cams and followers are hardened to reduce wear of the surfaces. 4.Variable speed motor coupled to camshaft of suitable range and Variac. 5.A dial gauge to note the follower displacement. 6.A technical manual accompanies the equipment.SERVICES REQUIRE FOR CAM ANALYSIS APPARATUS:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Bench area 0.5m x 0.5m x 0.5m height. 3.Tachometer to measure the jumping speed, (can be supplied extra)
Digital Coductivity Meter
| Usage | Industrial, Laboratory | |
| Material | MS | |
| Color | White |
Features
Highly Stable and Accurate Cell Constant Adjustment Facility Available in Lab & Field models Temperature Coefficient Correction facility| Display | 3 1/2 Digit LED | 3 1/2 Digit LCD |
|---|---|---|
| Range | 5 Ranges 0 - 1000 Mohs/cm | 2 Ranges 2 & Mohs/cm |
| Temperature Compensation | Manual 0-50oC | - |
| Cell Constrant Adjustment | Adjustable | Pre Adjustable |
| Conductivity Cell | Platinum DIP | Platinum DIP |
| Measuring Frequency | 1000 Hz | 1000 Hz |
| Accuracy | 1% FSI | 1% FSI |
| Power | 230v 10% | 1 x 9V Battery |
| Dimensions | 76 x 275 x 175 mm | 85 x 28 x 165 mm |
| Weight | 2 kg. (Approx.) | 0.8 kg. (Approx.) |
| Accessories | Conductivity Cell, Operation Manual, Dust Cover. | |
DDS RF Source and Network Analyzer
This unique instrument is RF source upto 1.7GHz with 10 to 400MHz in DDS mode of operation and few Network Analyzer capabilities.
