XTEMOS ELEMENT
AJAX PRODUCTS TABS
Flow Over Weir Or Open Channel Apparatus
Flow Over Weir Or Open Channel Apparatus:
A ‘WEIR’ is the name given to concrete or masonry structure built across a river (or stream) in order to raise the level of water on the upstream side and to allow the excess water to flow over its entire length to the downstream side. Weirs may also be used for measuring the rate of flow of water in river or streams.
Different shapes of “WEIRS” generally used are sharp-crested weir, broadcasted weir and ogee shaped weir.
In the unit a centrifugal pump sucks the water from the sump tank, and discharges it to a small flow channel. The weir is fitted at the end of channel. All the weirs are interchangeable. The water-flowing over the weir falls in the collector. Water coming at from the collector can be directed to the sump or can be directed in to the measuring tank for measurement of flow.
SPECIFICATIONS:
[1] The unit is provided with following weirs: (a) Sharp-crested weir. (b) Broad-crested weir. (c) Ogee shaped weir. [2] Pump 1/2 H.P. monoblock. [3] Flow measurement – Measuring tank calibrated water flow meter is used. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Floor surface – 2.5 m x 1.5 m. [2] 230 v, 5 amp supply with earthing connection
Car Air Conditioning Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Centrifugal Pump Test Rig
Centrifugal Pump Test Rig
Closed Circuit Type With S.S. Tanks, ISI Mark Pumps & Motors, Powder coated The closed circuit test rig consists of a “kirloskar make” monoblock centrifugal pump. The pump is provided with a vacuum gauge on suction pipe and a pressure gauge on discharge pipe. The gate valve is used to adjust the head on the pump. The discharge is measured by measuring tank / water flow meter. The input power is measured by energy meter.
Specifications:
l. Centrifugal monoblock- 1 h.p. 2. Pressure gauge and vacuum gauge for measuring the head. 3. Measuring tank of 400×400 x400 mm OR Water flow energy meter for measuring the discharge. 4. Stop watch. 5. Sump tank of sufficient capacity. 6. Energymeter to measure input power. 7. A technical manual accompanies the equipment.Features:
1. The equipment is coated with an attractive and anticorrosive powder coating. 2. The equipment consists of ISI standard (i) Monoblock ————————- Kirloskar make (ii) Energymeter ————————- Maxwell Jaipur make (iii) Water flow meter ————————- Kranti/Anand make.Services required :
(i) 440 v, 15 A, stabilized three phase A.C. supply. (ii) Floor area-2 mx2mxl.5m height (iii) Tachometer for speed measurement (can be supplied at extra cost)XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
CRUCIBLE TONG (IRON ZINC PLATED)
PH METER
Product Description
Due to our wide expertise, we are involved in manufacturing and exporting Digital pH Meter. The leading technology we have incorporated in this equipment results in accurate measurement of pH balance. Widely demanded in pharmaceutical, chemical, and food and beverage industry, this digital pH meter is available at a competitive price for our prestigious clients. Features:- Sleek design
- Accurate results
- Digital display
- Digital PH METER
- Max Make
- E.I. Make
- PH Electrode (Glass) Routine
- PH Electrode (Gell Filled) Unbreakable
- Pen type PH METER
Heat Transfer Activity
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Accessories For Plane Table
Description
We offer a wide range of very high quality Plane Table Accessories that are suitable for maps preparation and recording topography in various engineering surveys. This outfit consists of a plane table board with a fitted tripod. These products undergo various quality tests at each level of its production to ensure good quality and flawless performances. These products are basically used in the construction industry for the purpose for surveying the land for commercial use.Features :
• Export quality. • Reasonable price. • Customer centric organization. • Customizable.Specifications:
• Size: 54 X 34 X 22 + 8 CM. • Material: Green Bamboo, Natural and Environmental.
DC Motor Kit
Description
A simple kit for students to gain insight into field poles, armatures and switches, one mounting base, two coils of insulated wire , field pole, mounting bracket, two armature halves, one piece of insulating tubing, motor shaft, two commutator insulators, two bronze wire brushes, two shaft supports, four paper fasteners, a AA battery holder and 6 each of screws and nuts. Requires one AA battery, not supplied, with assembly instructions.
Variable Inductor
Description
The enamelled wire winding and a cylindrical soft iron core are built into this unit. The iron core displacement inside the winding can manually adjusted by the knob to give precise measurements up to 1.3 H. Connections are made through 4 mm sockets.Specifications:
Resistivity: 0.0165 W/m; Inductance: 0.15 to 1.3 H; Voltage: 30 V AC or 60 V DC.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
8085 Microprocessor LC LCD Trainer
Specification
• Intel 8085A CPU @ 6.144 MHz Clock speed. • RAM : 8KB expandable upto 32KB, Jumper selectable. • EPROM : 8KB expandable upto 32KB, Jumper selectable. • Lithium Battery Back up for RAM • PC Keyboard (104Keys) • 16x2 Alphanumeric Dot Matrix Liquid crystal display with back light • 3 Channel 16 Bit counter / timer terminated in a 10 pin connector using 8253 • 24/22 TTL I/O lines, terminated at 1 No of 26-Pin FRC connector by using 1 No of 8255/1No 8155 respectively • 8 Nos of Digital inputs terminated and given through on board 8 way Dip switch • 8 Nos of Digital outputs are terminated and displayed in the 8 Nos of SMD type LEDs • Digital I/O lines are terminated in 20-Pin connector • RS 232C compatible Serial port terminated in a 9-pin 'D' male connector • One VXT-Bus (50-Pin FRC Connector) for interfacing VBMB series of experiment boards for bus expansion. • Interrupts are terminated in a 5-Pin connector • Built in Line Assembler and Disassembler provided. • Software single stepping of user programs by instruction for software debugging.
Study of Operation Amplifier
Signal Generator
Audio frequency Generator is versatile instrument providing sine, square & triangular wave functions over a wide range from 2 220 KHz in decade ranges. The amplitude of the waveforms can be varied from 20 mV to 20 V peak to peak about zero level with the help of three step coarse control & fine control. The complete unit is enclosed in an attractive metal cabinet.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Linear Expansion Apparatus
Consisting of a metal rod, 500mm in length and 4.5mm diameter, enclosed in a well lagged, nickle plated brass tube with three tubules for steam, inlet, outlet and thermometer.
The metal rod to be studied is supported in the steam jacket by detachable conical cups situated at each end of the tube.
The apparatus is carried on a heavy gauge channel base at one end of which is an adjusting screw.
At the opposite end is a micrometer screw reading to 0.01mm for measuring the expansion.
Supplied complete with copper, brass & iron rods but without thermometer.
VM CRUCIBLE with Lid 25mm Dia x 38mm ht.
Optech Scanner
Description
Optech ILRIS Laser Scanner is fully portable, laser based ranging and imaging system for the commercial survey, engineering, mining and industrial markets. A compact and highly integrated instrument with digital instrument with digital image capture and sophisticated software tools, ILRIS is an industrial leading solution that addresses the needs of commercial users.
Skeleton Model, Miniature
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Digital Coating Thickness Meter
Description
Digital Coating Thickness Meter We offer high quality of Digital Coating Thickness Gauge. Statistics (Number of readings, average, Std. deviation, max. ,; min.) are updated with every reading and displayed simultaneously. It helps to decide how many readings are to be taken. Continue taking readings till you start getting reasonably consistent statistics.
Insect Storage Box
Description
For pinning of insects both inside top & bottom, White hardwood / Teakwood frame with melamine lamination on top & MDF sheet bottom is nicely polished. Top & bottom lined with 8mm thick soft pinning. washable EVA sheet. Inside glazed white. Raised wall with holes for insecticide inside bottom to make box air tight and pest proof. Fitted with brass hinges. index card holder & clips. Insect Storage BoxSize 53x45x9 cm Insect Storage BoxSize 45x30x7.5 cm Insect Storage BoxSize 38x25x7.5 cm Insect Storage BoxSize 30x23x7.5 cm
2 Stroke 1 Cylinder Petrol Engine Manual Driven
The engine will be sectioned to show the internal constructional details. The working of individual part and accessories like Valves, Pistons, pumps, Crank and Camshaft, etc. will be demonstrated. It is provided with Flywheel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes. The actual cut section engine will be supplied with key card & very interesting literature regarding working.
Linear Expansion Apparatus, Micrometer Screw Form
Description
A 500 mm long metal rod is supported in a plated brass tube with three tubules for steam inlet, outlet and thermometer. The tube is mounted on a stand with an adjusting screw at one end and a micrometer screw reading to 0.01 mm on the other, with terminals for connecting a bell or galvanometer to indicate contact. With copper, brass and iron test rods but without thermometer.
Tuning Forks welch type
Description :-
Consists of aluminum tuning forks, mallet in a wooden box.
Tuning forks are stamped with frequency and note.
Set of 8 (C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512)
Set of 13 (G-100, C-128, C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512, C-1024, C-2048 and C-4096)
Set of 8 (C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512)
Set of 13 (G-100, C-128, C-256, D-288, E-320, F-341.3, G-384, A-426.6, B-480, C-512, C-1024, C-2048 and C-4096)
