XTEMOS ELEMENT
AJAX PRODUCTS TABS
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Spherometer
Gear Box Actual Cut Section
Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
2 Stroke Petrol Engine Sectional Working Model
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Photon Energy Array
4 Stroke 1 Cylinder Diesel Engine Motor Driven
The engine will be sectioned to show the internal constructional details. The working of individual part and accessories like Valves, Pistons, pumps, Crank and Camshaft, etc. will be demonstrated. It is provided with Flywheel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes. The actual cut section engine will be supplied with key card & very interesting literature regarding working.
Torsion Of Rods Apparatus
INTRODUCTION:
A torsion test is quite instrumental in determining the value of modulus of rigidity of a metallic specimen. The value of modulus of rigidity can be found out thought observations made during the experiment by using the torsion equation.APPARATUS:
1. A torsion testing machine. 2. Twist meter for measuring angles of twist 3. A steel rule and Vernier Caliper or micrometer
Burner Bunsen – Teclu, LPG
Description
Burner giving a very hot flame, suitable for glasswork and soldering. A needle valve for fine flame adjustment is incorporated die casted base together with a tapered riffled tube connector. A unique spring operated gas safety lock is incorporated of the air/gas mixture. For use on natural gas supplies. Base dia. 80 mm and inlet tube 10 mm dia.Burner Specifications :
Tube Dia. - 13 mm Height - 150 mm Weight - 330 gXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
SILICON RUBBER CORK
PRODUCT DESCRIPTION
A Bung, Stopper or Cork is a truncated cylindrical or conical closure to seal a container such as bottle, tube or barrel. Unlike a lid, which encloses a container from outside without displacing the inner volume, a bung is partially inserted inside the container to act as a seal. These can be used for all types of glass bottles. These stoppers fit tightly to prevent chemical leaks. We are one of the very few manufacturers of silicone rubber corks, septa gasket, silicone rubber stoppers in India.
Features:
- Silicon rubber cork / stopper /bung,
- Silicon rubber cork for filtration flask.
Leopold Maneuvers Simulator
Description
One piece fetal baby with palpable fontanelles, spine, shoulders, elbows, and knees Fetal baby may be placed in normal, breech, or transverse position Fetal baby cradled between two “cushions” Cushions may be inflated independently of the other; inflation of the lower cushion raises the fetus to desired position; inflation of the upper cushion creates a firm abdomen as in the ninth month of pregnancy The Palpation Module is designed to be used with the Advanced Childbirth Simulator.
Micro Convavity Slides
Hand Stroboscope
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Ranging Rod
RAY OPTICS KIT
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Centrifugal Blower Test Rig
The apparatus consists of a spiral casing, which houses an impeller. Impeller is driven by a variable speed D.C. motor. Three, interchangeable impellers, viz. Radial forward and Backward curved vanes are provided with the unit. Digital indicators are provided for speed of impeller. A venture provided measures the discharge. Thus students can evaluate the performance of different impellers at various speeds.
SPECIFICATIONS:
1.Blower – Spiral casing with three interchangeable impellers viz. forward, backward and radial vanes. 2.Drive Motor-1 HP DC motor, 3000 RPM with Dimmer control to vary the speed from 300 to 3000 RPM. 3.Digital Speed indicator for speed measurement. 4.Ventura with water manometer to measure air flow. 5.Water manometer to measure discharge pressure. 6.Discharge pipe with flow control valve. 7.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Floor space of about 2m X 1.5m X 1.5m height. 2.230 V. 5A., 50 Hz, AC Supply.
Lagged Pipe Apparatus
Lagged Pipe Apparatus:
The apparatus consists of three concentric pipes mounted on suitable stand. The space between innermost and the middle pipe is fifed with a lagging material and the space between the middle and the outer most is filled with and other lagging material. The lagged pipe is heated with a cartridge heater inserted at the axle length of the pipe. Voltmeter and ammeter on the panel can measure the input to the heater. The intermediate temperatures can be measured by the thermocouples attached at the surfaces of the pipe. Thus the resultant conductivity of the materials can be found out.
SPECIFICATIONS:
1.Pipes : a)Gl pipe (innermost) – 6 cm. (Outer Diameter). b) Gl Pipe (Middle) – 8.5 cm. (Mean Diameter) c)G! Pipe (Outermost) – 10.7 cm. (inner Diameter) d)Length of pipes 1 Meter. 2.Heater : Nichrome wire cartridge heater placed centrally, of suitable capacity. 3.Control Panel : a)Single Phase Dimmerstat – 1 No. b)Voltmeter (0 – 250V) – 1 No. c)Ammeter (0- 2A) – 1 No. 4.Temperature Indicator : Multichannel Digital Temperature Indicator ranging (0 – 300 C) using Cr/AI ThermocouplesServices Required:
1. A.C. Single Phase 230 V electric supply 2. Floor Area-1.5 Meter X 1 Meter X 0.5 Meter High
Counters
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Human Histology
| Human Skin VS | Human Tongue Anterior Part TS |
| Human Tongue Posterior Part TS | Human Oesophagus TS |
| Human Stomach TS | Human Intestine TS |
| Human Intestine TS | Human Large Intestine TS |
| Human Vermiform Appendix TS | Human Spleen TS |
| Human Liver TS | Human Pancreas TS |
| Human Lung TS | Human Artery TS |
| Human Vein TS | Human Blood Smear |
| Human Trachea TS | Human Epiglottis TS Human Kidney TS |
| Human Bone TS | Human Nerve TS |
| Human Spinal Cord TS | Human Brain Cerebellum TS |
| Human Brain Cerebrum TS | Human Sperm Smear |
| Human Testis TS | Human Ovary TS |
| Human Oviduct TS | Human Mammary Gland TS |
| Human Vagina TS | Human Uterus TS |
| Human Thyroid Gland TS | Human Adrenal Gland TS |
| Human Cardiac Muscle TS | Human Salivary Gland TS |
Masses, Slotted
Solid brass, Accurate machined masses placed on a plastic and metal rack with handle.
Set of 8: 1x10 gm, 2x20 gm, 1x50 gm, 1x100 gm, 2x200 gm, and 1x500 gm, Total 1100 gm.
Set of 10: 1x10 gm, 2x20 gm, 1x50 gm, 5x100 gm, 1x500 gm, Total 1100 gm.
Set of 12: 1x1 gm, 2x2 gm, 1x5 gm, 1x10 gm, 2x20 gm, 1x50 gm, 1x100 gm, 2x200 gm, 1x500 gm, Total 1110 gm.
Set of 14: 1x1 gm, 2x2 gm, 1x5 gm, 1x10 gm, 2x20 gm, 1x50 gm, 5x100 gm, 1x500 gm, Total 1110 gm.
Micro Cover Glass
Made from clear optical glass, the cover glasses are uniform in size and free from scratches and striations. Packed in plastic box for easy handling.
Pack of 10 gms
Size
Square Size
18x18mm.
19x19mm.
22x22mm.
Rectangular Size
22x30mm.
22x40mm.
22x50mm.
22x60mm.
24x50mm.
24x60mm.
Circular Size
18mm.
19mm.
22mm.
24mm.
Fuel Supply System Petrol MPFI Type
Fuel Supply System Petrol MPFI Type (Actual Working Model) Multi Point Fuel Injection
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under :
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Igniter & Ignition Coil
9. Distributor
10. Spark Plugs
11. Power Supply
12. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of MPFI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
Autoclave Vertical Sterilizer
Specifications
Made of stainless steel with the inner chamber of a thick pressure gauge. The outer surface has a mirror polish. The lid of this autoclave is thick along with a safety valve, pressure release valve, and drain valve. Spring loaded valve to adjust the pressure. Works on 220V AC. Radial or wing nut type door locking. Digital temperature indicator. Water level indicator.| Dimension | Power | Capacity | |
|---|---|---|---|
| 250x450mm | 2KW | 22litres | |
| 300x500mm | 3KW | 40litres | |
| 350x550mm | 4KW | 50litres | |
| 400x600mm | 5KW | 75litres | |
| 450x600mm | 5KW | 95litres | |
| 550x750mm | 6KW | 187litres |
Vacuum Laboratory Desiccator
We provide impressive range of Vacuum Laboratory Desiccator.
Made of Polypropylene and Polycarbonate, these autoclavable vacuum desiccators can hold Vacuum upto 740 mm of Hg for 24 hrs.
The top dome, molded in rigid and transparent Polycarbonate, gives a crystal clear view of the desiccant placed inside.
The Knurled knob on the top provides easy handling of the dome.
The lower part is made of Polypropylene. An internal groove is provided on the flange to hold a silicon rubber O-ring.
The Polypropylene stopcock is fitted with a self lubricating PTFE plug.
This plug work three way i.e. Vacuum creation, shutting off & vacuum releasing.
Material : Polypropylene / Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Desiccator (Vaccum) PP/PC 150 mm | 1 | |
| Desiccator (Vaccum) PP/PC 200 mm | 1 | |
| Desiccator (Vaccum) PP/PC 250 mm | 1 | |
| Desiccator (Vaccum) PP/PC 300 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 150 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 200 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 250 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 300 mm | 1 |
