XTEMOS ELEMENT
AJAX PRODUCTS TABS
Phase Shift Keying Modulation and Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Phase Shift Keying Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supplies of ±12 V and ±5 V.
2. Built in Carrier wave Generator (Sine Wave) of 5 Vpp, 22 KHz ± 5% Frequency range with output on sockets.
3. Built in Data Generator using IC 7490 with four modulating signal outputs on sockets.
4. IC TL084 & IC 7486 are using for PSK demodulator.
5. Circuit diagram is printed on the milky white top panel and important connections are brought out on the sockets.
Six Phase Power Analyzer
Specification
• 6 phase measurement @ 50Hz • 6 voltage inputs (250V AC max., 50Hz) & 6 AC current inputs (5A max) • Zero crossing output for both voltage and current waveforms • 6Nos of phase sensing circuits provided to measure the phase difference of 2 waveforms • Signal Conditioning for Torque & Speed (QEP, Proximity, Optical) • After Signal Conditioned, 6 voltage outputs, 6 current outputs, 12 zero crossing outputs & 6 phase sensing outputs are terminated at 34 pin and 26 pin FRC connectors • Power input through banana sockets • Housed in a sleek cabinet
4 Stroke 6 Cylinder Diesel Engine
4 Stroke 6 Cylinder Diesel Engine – Motor Driven Actual Cut Section Working Mode
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine willbe supplied with key card & very interesting literature regarding working.
Bar & Gauge
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Microscope Slide Set Biology
Set of 25, this set covers the major requirements for a basic course in biology.
Selected slides from the zoology, histology and botany sections make up this useful set.
Supplied in Box.
Paramecium, E
Paramecium, conjugation, E
Hydra, TS
Hydra, with testis, TS
Hydra, with ovary, TS
Taenia (tapeworm), scolex, LS
Taenia, proglottid, E
Compact bone, TS
Striated muscle, LS
Cardiac muscle, LS
Spinal cord, TS
Nerve cells, smear
Skin, VS
Kidney, VS
Lycopodium strobilus, LS Spirogyra, conjugation, E Yeast, E
Lilium (lily), anther, TS Dryopteris, pinnule with sori, TS
Stigma with pollen tube Lilium (lily), anther, TS Dryopteris, pinnule with sori, TS
Stigma with pollen tube Cucurbita (marrow), stem, TS Lillium, ovary, TS
Tilia (lima), young and old stem, TS
Lumbricus (earthworm), TS , Typhlosole
Helianthus, stem, secondary thickening, TS
Oscilloscope
This Oscilloscope is corresponding to horizontal with small size. The bandwidth of Y axis is DC 10 MHz and the deflection factor is 5 mV 5 V / div. It can be up to 50 V / div. using with the 10:1 probe. Sweep deflection factor is 0.1 ?s / div.
(1) Single Channel Single Trace Oscilloscope
(2) Bandwidth : 10 MHz
(3) Confirms to EN61010-1 (1993) and EN-IEC61326-1(1997).
(4) Wide measurement
(5) High sensitivity and trigger lock
(6) Sweep switch adopts digital code switch and accuracy
(7) Proper to use in colleges and for engineers and technicians
(8) Deflection factor is 5 mV – 5 V / div in 1-2-5 Sequence in 10 steps
(9) Accuracy: ±5 % (
10) Maximum Input Voltage: 400Vpk
(11) Sweep deflection factor is 0.1 us / div to 0.1 s / div
(12) Accuracy: ±5 %
(13) Trigger Sensitivity: INT:1.5 div EXT:0.3 V
(14) Trigger mode: INT, EXT, LINE, TV
(15) Trigger Sweep Mode: NORM, AUTO, TV. LOCK.
(16) Calibration Signal: 0.5 V Square wave of 1 kHz.
(17) CRT Effective working Area: 8 x 10 div. 1 div = 6 mm.
(18) Auxiliary Power Supply: 220V AC 50Hz
Balance Spring
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Test Tube, with Interchangeable Stopper
Pressure Process Station
Panel Features
• Digital Panel Meters. • Mimic diagrams. • Pressure gauges are provided, wherever necessary.Softwares
• MATLAB • LabVIEW • PLC • C/VB CompatibilityFeatures
• The Pressure process station is an attractive module comparing to the Analyzer and Laboratory trainer. • All are the industrial standard (4-20)mA interfacing signals. • It provides a real industrial feeling of the process to the students. • A Piezo Resistive Pressure Transmitter (0-7)Bar is used to sense the pressure. • An Electronic Regulated Power supply is fixed for voltage Regulation. • An electro pneumatic converter is mounted to control the pneumatic control valve. • A globe Pneumatic Control Valve for controlling flow of air. • An air regulator cum filter is provided for Air regulation. • A two separate pressure tank is provided as process tank with pressure gauges and relief valves. • All the air flow lines are fitted by flexible hoses/fittings for better reliability. • Hand valve provisions are given for series, parallel connection of pressure tanks. • USB/Serial port data acquisition is provided.
Evolution
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Ultrasonic Interferometer
Ultrasonic Interferometer is a simple and easy to use unit for the accurate measurement of ultrasonic velocity in a Liquids and Liquid systems at the desired temperature (and at desired frequencies).
FEATURES:
• Accuracy in wavelength measurement – 0.01mm • Digital Panel Meter ( DPM) for observing the change in the reading between nodes /anti nodes (75mV approximate between a node and anti node) • Easy replacement of transducers with other frequency • Only one Liquid cell is required for all frequencies • Built in IC regulated power supplies. • The frequency of the Crystal oscillator at the piezo electric transducer is so matched at the 3 digit Decimal accuracy • The accuracy of Meter is 3 Digit Decimal • Stainless Steel based mechanical setup.ACCESSORIES:
• Liquid cell - One (with provision for water circulation) • Transducer (Longitudinal, 2MHz) - One • Micrometer assembly - One (with Tx)
Cooling System Of An Automobile
In this model the working of a cooling system of a car is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a cooling system of a car are shown in actual working form. This model helps the student to understand the working of the cooling system of a car very easily. It is specially made dissectible for demonstration purposes.
Specific Heat Of Air Apparatus
The apparatus consists of heating element on which the air is blown. The difference in temperature of air is shown by the temperature indicator. The flow of air is measured by the orifice meter. The input to the heater is measured by voltmeter and ammeter. Thus the specific heat of air can be found out.
SPECIFICATIONS:
1.Air blower connected to FHP motor. 2.Orifice meter to measure the air flow, Heater – 1 KW heating coil placed centrally in the test section. 3.Multi channel digital temperature indicator – range 0 to 300 c. 4.Voltmeter and ammeter to measure the heat Input.SERVICES REQUIRED:
1.220 volts single phase stabilized AC Electric supply. 2.Floor space – 2 m. X 1 m. X 2 m. Height.
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Unsymmetrical Bending Apparatus
DESCRIPTION:
Apparatus consist of an angle of size 1” x 1” x 1/8” or in equivalent metric units of length 80cm is tied as a cantilever beam. The beam is fixed at one end such that the rotation of 450 intervals can be given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement is provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end. A dial gauge with magnetic base is supplied with the apparatus.EXPERIMENT MANUAL:
• To study the behavior of a cantilever beam under symmetrical and unsymmetrical bending. • Using a Dial gauge shown a increasing and decreasing of heights.
Thin Cylinder Apparatus
A heavy bench top unit for studying the stress and strain in a thin walled cylinder under internal pressure. A thin walled cylinder is mounted between two support blocks. Internal pistons and seals create oil sealing. A handwheel at one end of the apparatus enables the cylinder end conditions to be adjusted to either open or closed. The internal pressure is adjusted by means of a hydraulic hand pump on the apparatus. An analogue pressure gauge displays the internal pressure whilst a pressure transducer gives feedback to the Data Acquisition Interface and Software supplied. Strain gauges are arranged on the external surface of the cylinder to measure the radial and circumferential surface strain. The strain gauges are at various angles.
Latent Heat of Steam Apparatus
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Transmission Line Trainer
This trainer is designed for study of co-oxial cable characteristics like Impedance measurement, VSWR measurement etc., It is based, i) The latest technology of DDS Based RF source. ii) Directional coupler for VSWR Measurement. iii) TDR to measure the cable fault.
Specification
• DDS RF Source - Frequency: 10 to 400MHz. - Step Size: 1KHz. - Direct Digital Synthesis (DDS) Method Based. - Since DDS Device is primarily digital, it offers. • Display: Graphics LCD display of 240x128 pixels with backlight to plot VSWR, TDR characteristics etc., • One directional coupler provided for VSWR, Return loss measurement. • In-Built RF Detector for 10-400MHz Frequency range. • In-Built TDR (Time Domain Reflectometer) to measure and study nature of discontinuation in the co-axial cable. • Output Impedance: 50 ohms. • Co-axial cable: Various lengths of 50 ohm, 75 ohm cables supplied. • All relevant waveforms are displayed graphically in the Graphics LCD
Electromagnetic Field Demonstrator
Description
This apparatus demonstrates the magnetic field patterns associated with the different shapes of current carrying conductors. Comprises three conductors, each of different shape/configuration – straight rectangular, circular loop and solenoid all mounted on a plastic base. Each configuration is provided with a pair of 4 mm sockets to connect them to a low voltage DC power source, with output current not exceeding 5A With the included iron filings and 8 magnetic compasses, you can investigate the associated field and flux patterns.
