XTEMOS ELEMENT
AJAX PRODUCTS TABS
Linear Air Track
Angular section aluminium alloy track, length 255cms, with staggered air holes, supported on two light alloy castings positioned 45 cm from each end of the track.
One support has a two- point contact and other one-point contact for lateral and horizontal adjustments for which a knurled screw is provided.
Large catapult arms with slots for elastic bands are fitted to each end of the track.
A fully fitted to one end of the track enables experiments involving acceleration under a constant force.
Identical end caps enable air to be introduced from either end of the track, bung being supplied to close the end not being used.
The vehicle buffer attachments and clamping screws are matt black to help interpretation of stroboscopic photographs.
Verification Clarke S Maxwell Reciprocal Theorem
Apparatus for Verification of Clarke’s Maxwell Reciprocal Theorem
Apparatus consist of a mild steel beam 100cm long and 1.25cm x 4mm in cross section with graduations at every 10cm along the length. It should be supported on two knife edge supports 70cm apart with a 30cm overhang on one side. Reciprocal theorem can be verified by direct measurements of the deflections of various points with the help of a dial gauge due to a load placed at the reciprocal points. A dial gauge with 25mm travel (with a magnetic base) should be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Experimental Capabilities: To verify Clerk’s Maxwell reciprocal theorem by means of a mild steel be
Front Axel Assembly With Differential Gear
Front Axel Assembly With Differential Gear (Actual Cut Section)
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Dicot Stem Anatomy T. S. & L. S.
Description
This model shows the transverse and longitudinal section of a dicotyledonous stem in which case the cambium ring has been formed but no secondary growth has yet taken place. Useful model for study of epidermis, lentice , cork layer, cork cambium, cortical parenchyma ,starch sheath, medullary rays, phloem, sieve plate, sieve tube, phloem parenchyma and inter fasicular cambium ,xylem, pitted vessels, bordered pitted vessels, annular vessels, spiral vessels, pith etc. Mounted on base, with key card.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Multi-Functional Nursing Simulator (Female)
Description
Designed according to the demand of the clinical principles and the guidelines of nursing training. This multifunctional simulator could simulate an actual circumstance for practice. Multiple functions, rural practice, easy assembly, well shaped appearance and correct anatomical landmarks provides a very good training for practice.Features:
Head Care. Body care. Patient moving. Different lying pose. Bilateral and Unilateral oxygen inhalation. Atomization inhalation therapy. Nasal Feeding. Gastric lavage training. Intravenous Injection. Intramuscular Injection. Hypodermic Injection. Various fistula orifice washing practice. Female Catheterization. Female Bladder Washing. Enema Treatment. Simulator Assembly.
Large Rectangular Transparent Tank
Motor With Solar Cell
Digital Colony Counter
Description
Fitted with automatic 3 Digits LED Digital Display. Counting plate with illuminated standard wolf hugel ruling ensures clearly differentiated and sharply defined colonies. Each touch of making pencil in the petri dish increment the colony count by '1' and the glowing LED Display depicts the total colony count. Provided with a manual reset of digital display, ON/OFF Switch, counting plate, 100 mm. dia lens, cord and plug. To work on 220V A.C.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Earth, Neutral And Live Board Demonstration
Description
This apparatus is an effective demonstration of how the earth wire and fuse act together to protect both the user and the appliance. When the appliance is connected correctly and the LEDs in the appliance will illuminate to show the appliance is working. A fault is then demonstrated by swapping the live wire from inside the appliance to the case to show either the fuse melts (protecting the user and appliance) or in the case of no earth wire, the LEDs illuminate to indicate the passage of current through the person to ground. The fuse is easily visible and can be seen to ‘blow’ when a fault occurs.The unit is supplied with 10 m of fuse wire and full instructions. A 12 V DC power supply is required. Connections are made via 4 mm shrouded sockets.
Lathe Tool Dynamometers
This is a strain gauge type two component lathe tool dynamometer designed to measure vertical and horizontal forces on the while orthogonal cutting process. The unit is in two parts one is mechanical sensing unit or tool holder, which can mounted on the top of the Ross slide after removing swivel base and compound slide of a lathe and digital force indicator. With this Dynamometer student can study the change in these forces by varying Speed, Cut and Feed.
FEATURES:
1.Rigid in construction 2.Sensitive transuding and amplifying system for accuracy in force measurement. 3.Compact Digital force indicator. 4.Use of cutting fluid during operation is possible.SCOPE OF SUPPLY:
1.Mechanical sensing unit or Tool Holder with string gauges. With H.S.S. tool of ½ “ size. 2.Control panel housing digital force indicator to measure two forces simuletensiously, balancing potentiometers, connoting cable. 3.Necessary switches, fuses and polycarbonate front plate. Range o to 500 Kg. 4.Centre Height, P.C.D.of clamping bolt size, clamping Bolt size. Three component lathe tool dynometer is also available.
Laminar Air Flow
Product Details
| Material | : | STAINLESS STEEL |
| Model | : | Horizontal |
| Switches | : | Processor based switches for blower, LED light & UV light With LCD back light display. (UV light with Timer) |
| Pre-filter | : | 99.00% down to 5 micron. |
| HEPA Filter | : | 99.97%-99.99% down to 0.3 micron, Mesh guard for protection. |
| Airflow | : | Frontward Horizontally |
| Noise Level | : | 60 decibel ± 5%. |
| Velocity | : | 0.35-0.50m/sec. |
| Work Table | : | Made up of stainless steel 304gr. Cock for gas on work table. |
| Side Panels | : | 6mm±.5mm thick acrylic sheet. |
| Front door | : | Made of acrylic. |
| UV Lamp | : | 15/30W, make Philips Holland, |
| Illumination | : | LED White Light. |
| Pressure | : | Digital Manometer 0-50mm range with filter failure alarm. |
| Power Supply | : | 230V ± 10V/50 Hz single phase A.C. |
| Cabinet | : | 304 grade. Stainless Steel. |
| Heavy Duty Blower | : | Dynamically balanced with 0.25 HP Electric Motor Mounted on anti vibration pad 1440 RPM motor. |
Working Area Size
60x60x60cm. 90x60x60cm. 120x60x60cm. 180x60x60cm.
Alumina Crucibles
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Charle’s Law Apparatus
Description
To determine co-efficient of expansion of a gas at constant pressure. A glass U-tube with a bulb and stopcock at one end, the other limb being open. An outlet tube from the bottom of the U tube passes through a rubber bung and has a stopcock at the end. The stem below the bulb is graduated 3 x 0.1 ml. An inlet tube with a mohr clip also passes through the bung. A glass water jacket encloses the U tube. All glass parts made of borosilicate glass requires only 20 ml mercury, which is not included.
Multi Process Trainer
Features
• Pressure transmitter mounted at the bottom of the process tank • Flow transmitter (DPT) with rotameter mounted across the pipe line to sense the flow of water • Temperature sensor of (RTD) type mounted at the outlet of the heater • An industrial type heater as a heat source • FHP pump for water Circulation • SS Storage tank of 15 liters Capacity • Power driver provided to vary the pump speed and Heater Power. • Orifice plate is used for pressure drop measurement. • An electronic signal conditioner is provided. • Bourdon tube pressure gauge is provided to measure the tank. • Latest power driver is used to drive the pump & heater. • USB/Serial port data acquisition is provided.
Multiple Input/Output Process Trainer
Panel Features
• Power ON/OFF switch • Heater selection switch • Heater and pump indicators • High current fuse carrier for • Heater protection • Provision to run the stirrer • Digital panel meters • Two numbers of industrial PID Controller • Electrical test points are provided to measure the current signal • Mimic DiagramFeatures
• Two numbers of flow Transmitter (DPT) are provided to sense the flow of the liquid. • Three numbers of temperature transmitter (RTD) are provided at various stages to measure the temperature. • Five numbers of level sensor (RF capacitance) are provided to sense the level of each tank. • Industrial type Conductivity sensor is provided to analyze the conductivity of given Solution. • RTD sensor (or) Thermocouple acts as a temperature sensor. • Digital panel meters are provided to indicate the output of each sensor. • Provision to measure the conductivity. • Two numbers of motorized control valve or pneumatic control valve are provided to control the flow of the pipe line. • A powerful thyristor based power driver is provided to drive the heater power. • An industrial type water heater is used as a heat Source. • Storage tank of 50 litre capacity (SS). • Process tank of 15 litre capacity (SS). • Four numbers of acrylic tank are provided to study the response of four tank systems. • In necessary location Ball valve, globe valve and needle valves are provided. • Two numbers of stirrer are provided in the temperature process and alkaline process. • Three numbers of centrifugal pump (FHP) is used to circulate the water from storage tank. • Six numbers of rotameter are provided in the process inlet to visualize the real flow. • Regulated power supply is mounted in the panel. • All the flow lines are fitted by (SS) pipe fitting. • An over head tank is provided to give constant flow. • All the equipments are mounted in a rugged and mobile type metallic work station.
IoT Development System
The industrial networks are primarly concerned with Programmable Logic Controllers(PLC),Distributed Control Systems(DCS), Supervisory Control and Data Acquistion Systems(SCADA) any many other hetrogenous devices in the form of differnt applications. More over these devices are based on either wired or wireless communication protocols like Profinet, Profibus, MODbus, WiFi, Zigbee and Etc.
Specification:
• To impart the knowledge about Industrial IoTa the Students, We have designed a IIOT trainer kit, which have inter-quark chip based IoT Gateway. • This Gateway is a universal Gateway supports many different types of communication protocols such as wired and Wireless communication for industrial applications. • The IIoT Gateway connected with Siemens based Distributed Control System(DCS), Programmable Logic Controller(S7-1200, S7-1500) using S7-protocol and OPC UA. • The Intel centrino based powerful WiFi chip enables us to the access data via Mobile Application. • The Gateway can get the internet connectivity via Ethernet and WiFi also. • This Gateway can communicate with our own ingenious data acquisition system using RS485 BUS and RS232 Bus. • The USB based communication exchange the data between Zigbee co-coordinator and Gateway.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Ticker Tape Timer
For the measurement of velocity and acceleration, using timing marks made on a moving paper tape by a vibrating striker.
Designed to operate on a 12V A.C. supply and uses the mains frequency as its timing standard.
The unit is housed in a moulded case including mounting flanges.
The top of the case caries a tape guide which incorporates a carbon paper disc support and an adjustable anvil for the striker point.
All moving parts are fully enclosed and a pair of 4mm sockets are provided on the side of the case for connection of the electrical supply.
Supplied with a roll of self marking paper tape.
Paper tape : 100m of paper tape, 9.5mm wide.
Carbon Paper Discs : 40mm diameter, with 3mm hole, cut from long life plastic film type carbon paper.
Resistance Units, Interlocking
89C51 Development Board
Specification:
• High Performance MCU:P89V51RD2 8 bit with 64K program flash, 1xUART, 4x 8bit I/O, 4level priority,7 interrupt sources, upto 40 MHz operation • All the IO lines are terminated through 4nos Pin FRC Connectors • One SPDT Switch provided for PROG/EXEC mode selection and one SPDT switch for Power ON/OFF Control. • RS232 interface with two status LEDs for Programming and UART interface • One 8 – way DIP switch for Digital Logical Input • On board 8 Leds for Digital Logial Output • 4x4 Matrix Keypad, On board 16x2 LCD • On board RTC interface with four function keys • Two 12V relay with driver Circuit for DC Motor 0.5 Kg Stepper Motor with relevant driver circuit • On board DAC terminated via 2-pin Phoenix Connector • On board 8 channel ADC with Temperature sensor
Light Box and Optical Set
Description
A Robust light box in matt black finish with a 12 V 24 W axial filament lamp with flexible leads. One end of the box takes a cylindrical convex lens in an adjustable sliding mount to enable production of convergent, parallel or divergent beams. Complete with accessories which consist of: 5 Plastic blocks, one rectangular, One semicircular, One equilateral prism 60° x 60° x 60°, One right angle prism 90° x 60° x 30° and one right angle prism 90° x 45° x 45°. 3 Cylindrical acrylic lenses: one double convex, one double concave, both having the same radius of curvature and one thick convex lens. 3 Mirrors, one plane glass, one curved parabolic and one curved semi-circular. 2 Slit plates, one with three narrow and one narrow slits, the other with four narrow and one wide slits 1 Set of eight colour filters, Red, Green, Blue, Cyan, Violet, Yellow, Orange and Magenta. 1 Set of coloured cards, Red, Green, Blue, Violet, Orange, Cyan, Yellow and Pink. Complete with one spare lamp, in box.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Frequency Modulation And Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Frequency Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supply of ±12 V.
2. Built in Modulating signal Generator of 2 KHz and 4 KHz selectable with a toggle switch with Amplitude to 3V peak to peak approximately.
3. Circuit diagrams for Modulator and Demodulator are printed on the milky white top panel
Cryovial
Cryovial are normally used for storage of Biological material, human & animal cells.
These sterilized tubes are provided with white prominent graduation and a long marking area for sample identification.
The cap of these Cryovial is provided with a seal ring inside to make it completely leak proof.
The longitudinal grooves in the base give a non-twisting feature to these vials when paced in a cryo rack.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Cryo Vail - Internal Thread 2.0 ml | 500 | |
| Cryo Vail 1.8 ml | 1000 | |
| Cryo Vail 4.5 ml | 500 |
Volumetric Flask
We introduce our special quality Volumetric Flasks.
These Volumetric Flasks are blown in Polypropylene and are strong, unbreakable and have good contact clarity.
These autoclavable Volumetric Flasks are provided with screw caps to prevent leakage.
These Volumetric Flasks are economic as well.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Volumetric Flask 25 ml | 6 | |
| Volumetric Flask 50 ml | 6 | |
| Volumetric Flask 100 ml | 6 | |
| Volumetric Flask 250 ml | 3 | |
| Volumetric Flask 500 ml | 3 | |
| Volumetric Flask 1000 ml | 2 |
