XTEMOS ELEMENT
AJAX PRODUCTS TABS
Ice Melting Kit
Description
Demonstrates the difference in thermal conductivity of two different materials. The kit consists of two identical blocks, one made of aluminum and other made of plastic. When an ice cube is placed on aluminum it turns into water in seconds, while on plastic block it melts slowly. The aluminum block has a larger heat capacity and a higher thermal conductivity while the plastic block has lower values of both parameters. With instructions.
CNC Lathe Trainer
Controller:
Type of control system: PLC based system Main Spindle Drive : AC Motor with VFD Z and X Drives : Stepper drive with Ramp function Input to Stepper : Optically Isolated Motor Drive :TTL Compatible Run Speed Control : Computer controlled with software Interpolation : liner / Circular /Parabolic Cycles Used :G,M,S,T,F,I,K,M,F Cycles : Circular Interpolation /canned Threading : Straight/Taper Power Devices : Short Circuits and over Temperature Protected Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
Center height : 100mm Swing over Carriage : 80mm Distance between Centre : 300mm Longitudinal Travel : 310mm Weight : 800kg Dimension in mm : 1300 x 800 x 1400 Rapid Travel : 700mm/min Resolution Z Axis : 5micron Resolution X Axis : 5micron Automatic : providedAXIS TRAVEL:
X Axis : 80mm Z Axis : 310mmSPINDLE:
Spindle Speed : Continuous Variable Spindle Power : 2 HP Inside Taper : MT3 Speed Range : 50 to 3000Rpm
Tubes, Culture, Media, Round Bottom with Screw Cap and PTFE/Rubber Liner
5KVA IGBT Based Converter Inverter System
DC Motor Specification
• Power : 3HP • Armature voltage : 220V DC • Field voltage : 220V DC • Speed : 1500 RPM • Make : Benn • Double side shaft extensionSlip Ring Motor
• Type : 3phase slip ring induction motor. • Power : 2KW • Stator voltage : Three phase 415V AC, 4A • Rotor voltage : Three phase 210V AC, 6A • Speed : 1410 RPM • Make : BenndsPIC 30F4011 based PWM Controller
• Microchips’ dsPIC30F4011 16 bit digital signal controller operating at 20MIPS • On chip 48K Bytes flash program memory • On chip 1K Bytes data EEPROM • On chip 2K Bytes RAM • Four Compare/PWM output • Six PWM output for Motor control • One 3 channel Quadrature Encoder interface circuit/4 capture input • 9 Channels 10 bit ADC of 500Ksps conversion tune. • One RS232 Compatible serial port Opto isolated & terminated at 9 pin D male connector • 6 PWM outputs and two capture inputs and two compare outputs are terminated at 34pin FRC connector. • 4 Channels of DAC output & 5 channels of ADC inputs are terminated at 26 pin FRC connector • 16 x 2 alphanumeric LCD displayXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Human Male Pelvis
Burner Bunsen-Economy
Description
This is one of most inexpensive option without flame stabilizer. The burner tube is made of brass and mounted on pressed steel powder coated base. Base dia is 80 mm. overall height of burner is 135 mm burner tube dia 12 mm. Suitable for LPG / Butane gas.Burner Specifications :
Tube Dia. - 12 mm Height - 130 mm Weight - 160 g
Aluminum Calorimeter, with wooden box
Ranging Rod Metal
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Thermal Conductivity Of Metal Rod
The apparatus consists of a copper bar, which is heated at one end, a heat sink is provided at other end. The test section of bar is properly insulated and thermocouples are attached along the length of bar. Heat conducted through the section of bar is measured by heat collection in water-cooled heat sink. A panel comprising of controls and measurements is provided, which provides easy operation and sturdy mounting of unit.
SPECIFICATIONS:
1.Metal Bar – 25mm of adequate length, provided with 8 Thermocouples along the length, Band heater at one end and water-cooled heat sink at other end. Test portion of bar is insulated. 2.Instruments panel comprising of. Voltmeter … 1No. Ammeter … 1No. Dimmerstat 0-230v, 2A, capacity. Multichannel Digital temperature Indicator. 3.Measuring flask and stop clockSERVICES REQUIRED:
1.Bench area of 1.5m. x 1m. at working height. 2.230 v, AC, electric supply with earthing connection. 3.Water supply at the rate of 2 lit/mm
Round Bottom Centrifuge Tube
Avail from us, a flawless variety of Round Bottom Centrifuge Tube , which is popular for its better quality and precise engineering.
Being one of the chief Exporter and Trader in this industry, the company provides Round Bottom Centrifuge Tube at the most competitive prices.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Centrifuge Tube Round Bottom 16 ml (P.P) | 50 | |
| Centrifuge Tube Round Bottom 50 ml (P.P) | 50 | |
| Centrifuge Tube Round Bottom 16 ml (P.C) | 50 | |
| Centrifuge Tube Round Bottom 50 ml (P.C) | 50 | |
| Cap for 16 ml Centrifuge Tube Round Bottom | 100 | |
| Cap for 50 ml Centrifuge Tube Round Bottom | 100 | |
| Oak Ridge Centrifuge Tubes 30 ml | 12 | |
| Oak Ridge Centrifuge Tubes 50 ml | 12 | |
| Oak Ridge Centrifuge Tubes 100 ml | 12 |
Calorimeter, Electric
Metabolic Cage for Rat
Description
Animal waste is directed through a collection funnel and onto a linear diffuser guide. The diffuser guide allows solid matter to travel down the top ridges of a 50% incline, passing over a urine port, and into a fecal collection vessel. Liquid waste flows along grooves down the inclined diffuser guide, passing through the urine port, and into a urine collection vessel. A urine deflector prevents excess urine from splashing and contaminating fecal specimen. Separate urine and feces samples are collected in two separate tubes.Features
Reliable experiment results due to better separation efficiency Food hopper design reducing the access or stay of animal inside food hopper Practicality of use due to less components or parts| Minimal animal stress: | Sample removing is without stressing animal, access to all elements below the cage floor without disturbing animal |
| Durability: | Most components are made from autoclavable polycarbonate and S.S. 304 material |
| Versatility: | Unit accommodates various species with simple feeder and floor change Space saving |
| Economy: Few parts, simple and rapid assembling |
Components Included
Polycarbonate cage with lid
Polycarbonate collection funnel
S.S. 304 floor grill for Mice and Rat
Polycarbonate Linear diffuser guide
Urine collection tube P.P.
Feces collection tube P.P.
Polycarbonate water bottle 250ml with holder
Waste water collection tube P.P.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Thermocouple, Double
Rotary Pipette Stand
Moulded in Polypropylene, the unique Rotary Pipette Stand holds a maximum of 94 pipettes and rotates on a central vertical axis for convenient selection of any particular pipette.
The lower rotating disc has four concentric troughs with tapered sides and open bottoms that cradle the pipette tips protectively and permit water drops to run off.
The upper disc has a grid pattern concentric with the bottom disc and keeps the pipettes vertical.
Liquids draining off the pipettes are retained on the top of the stationary base by the outer ring.
Our Rotary Pipette Stand can be easily disassembled and reassembled.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pipette Stand (Rotary) - For 94 pipettes | 1 | |
| Pipette Box | 4 |
SPECIMEN JAR (RECTANGULAR JAR), With Cover
Set of Masses, Brass
Set comprises masses of brass with slots, brass hangers with hook. Fine finish, masses removable and replaceable on hanger.
Set of 9 weights, one hanger each of 10 gm. Total weight 100 gm.
Set of 9 weights, one hanger each of 25 gm. Total weight 250gm.
Set of 4 weights, one hanger each of 50 gm. Total weight 250gm.
Set of 9 weights, one hanger each of 100gm. Total weight 1000gm.
Set of one hanger 20 gm. three weights 20 gm. Total weight 100gm.
Set of one hanger 50 gm, nine weights 20 gm. One weight 10 gm. and two weights 5 gm. Total 250 gm.
Spare slotted weights and Hangers 5gm., 10gm., 20gm., 50gm., and 100 gm. are also available.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Weighing Bottle with Interchangeable Stopper
Window Air Conditioning Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Magnetic Stirrer with Hot Plate
Maximum speed 1200 RPM.
Suitable for stirring all volumes, supplied with a teflon coated magnetic stirring bar.
Particulars
Magnetic Stirrer with Hot Plate, Volume 2 litre Magnetic Stirrer with Hot Plate, Volume 5 litreFeatures
Automation Type : Automatic Material (Body) : Mild Steel Material (Top Plate) : Stainless Steel Phase : Single Phase Power : 220 V Frequency : 50 HzXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Wooden Levelling Staff Telescopic type
Description
We bring forth an impeccable array of Wooden Leveling Staff to eminent customers. Products that we come up are ideally used to cater to the various needs and preferences of customers of various construction industry along with others. Therefore, this range is quality tested as per industry laid parameterst.
Linear Expansion Apparatus
Consisting of a metal rod, 500mm in length and 4.5mm diameter, enclosed in a well lagged, nickle plated brass tube with three tubules for steam, inlet, outlet and thermometer.
The metal rod to be studied is supported in the steam jacket by detachable conical cups situated at each end of the tube.
The apparatus is carried on a heavy gauge channel base at one end of which is an adjusting screw.
At the opposite end is a micrometer screw reading to 0.01mm for measuring the expansion.
Supplied complete with copper, brass & iron rods but without thermometer.
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Digital Planimeter
Description
We have for our clients a wide range of digital planimeter that are known for their good quality and ability to display the accurate results. Technology advanced, these survey instruments comes with a clear display. The digital planimeter that we have are used for measuring distances on the maps or drawings.
Micro Controller Development Board
Microcontroller development board is designed to train engineers about the structural design, instructions and utilize the 8051 microcontroller board. A 40 pin ZIF socket for easy insertion of 89 series microcontroller with four 10 Pin FRC connectors is provided on the board. Outputs from I/O port from microcontroller are available on FRC connectors those can be easily connect with different modules. Microcontroller Development Board consists of EEPROM with 4K memory changeable with more RTC DS1307 with 32 KHz crystal with battery backup One 12 V stepper motor with drivers.One 16 x 2 LCD display. 8 Output LED indicators. 4 multiplexed 7-segment display. 8 single bit toggle switch. 4 x 4 matrix keyboard. Single Channel ADC with potentiometer and provision of external inputs RS 232 serial communication. One 12 V DC motor driver.
Refrigeration Trainer Electrolux Type
This type of refrigeration is usually used for domestic purposes only as it is complex in the construction and working. This type of refrigerator was developed in 1925 by Munters and Battzervan when they were studying at Royal Institute of Technology At Stockholm for their undergraduate course. This type of refrigerator was known as three fluid refrigeration system. The elimination of aqua pump from the absorption system with the complete absence of moving parts and work input. The main purpose of removing the pump was to make the machine noiseless. It uses refrigerant as a solvent s and an inlet gas for inlet of the system. The inert gas is continued to the lower side of system only by its system. It is possible to maintain the uniform pressure throughout the system and after sometime permitting the refrigerant to evaporator at low temperature corresponding to its partial pressure. In the high pressure side system (generator and condenser), there exists only the refrigerant which is subjected to total pressure of the system so that it is condensed by using normal cooling water as air as it is done in other system.
The strong aqua ammonia solution is heated in generator by the application of external heat source. The water vapor carried with ammonia vapor is removed in separate form as shown in figure. Then the dry ammonia vapor is passed into the condenser and it is condensed by using external cooling source. The liquid ammonia flows under gravity in the evaporator and it evaporates. The mixture of hydrogen and ammonia vapor is passed into the absorber and the weak solution from aqua ammonia from the separator is allowed to follow into the absorber, through tray this weak aqua ammonia solution comes into contact with hydrogen separated. This strong solution is further passed to the generator and it completes the cycle.
