XTEMOS ELEMENT
AJAX PRODUCTS TABS
Refrigeration Test Rig
Features
• 5 Nos of thermocouples are provided to measure the temperature at different points. • One multi channel temperature indicator is provided to display the temperature • One capillary tube and one thermo expansion valve is provided to check the performance separately. • Compressor supplies refrigerant through evaporator to find out cooling effect • 4 Nos. of Pressure Gauges are provided to measure the pressure at various point • One Energy meter is proivded to measure the overall power consumption • One voltmeter is provided to display the voltage. • One ammeter is provided to display the current.Specification
• Compressor :Hermatic • Capacity : 1/4 Ton • Supply : 230 V AC / 50 Hz • Condensor : 12 Coil • Evaporator : 15 Liter Capacity • Refrigerant : R134A
CNC Lathe Trainer
Controller:
Type of control system: PLC based system Main Spindle Drive : AC Motor with VFD Z and X Drives : Stepper drive with Ramp function Input to Stepper : Optically Isolated Motor Drive :TTL Compatible Run Speed Control : Computer controlled with software Interpolation : liner / Circular /Parabolic Cycles Used :G,M,S,T,F,I,K,M,F Cycles : Circular Interpolation /canned Threading : Straight/Taper Power Devices : Short Circuits and over Temperature Protected Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
Center height : 100mm Swing over Carriage : 80mm Distance between Centre : 300mm Longitudinal Travel : 310mm Weight : 800kg Dimension in mm : 1300 x 800 x 1400 Rapid Travel : 700mm/min Resolution Z Axis : 5micron Resolution X Axis : 5micron Automatic : providedAXIS TRAVEL:
X Axis : 80mm Z Axis : 310mmSPINDLE:
Spindle Speed : Continuous Variable Spindle Power : 2 HP Inside Taper : MT3 Speed Range : 50 to 3000Rpm
Human Larynx With Tongue
Description
Natural size, three parts. Larynx showing cartilages, ligaments, muscles, relief of mucous membrane and thyroid gland. Tongue showing front part of the lower jaw which is detachable and separates into two parts, median section, sublingual gland and sub mandible gland are shown. on base with key card.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Mock Layout Of Car Wiring Latest Type
Mock Layout Of Car Wiring Latest Type
All the components used in the apparatus are of modern car. The complete mock layout is beautifully divided into 5 sections as under
(A) Front Lighting Panel
(B) Dash Board Panel
(C) Ignition System
(D) Rear Lighting Panel
(E) Motorised Charging System
With the help of this mock layout system its becomes very easy for the students to understand the actual working of electrical system of a modern car.
TMS320VC5416 Based DSP Trainer
This Kit provides new performance enhancing Features such as USB Communications. This is Suitable for applications that require optimized Combination of Power Performance & area. Suitable for the range of Signal processing applications, including speech Compression / decompression Speech recogniation, echo generation and Cancellation.
ON-CHIP FEATURES:
• 160MIPS Performance, can operate upto 160MHz • Advanced multi bus architecture with one program bus, three data buses and four address buses • 40-bit arithmetic logic unit (ALU), including a 40-bit barrel shifter and two independent 40-bit accumulators • 17-bit × 17-bit parallel multiplier coupled toa 40-bit dedicated adder for non pipelined single-cycle multiply/accumulate (MAC) operation. • Compare, select, store unit (CSSU) for the add/compare selection of the Viterbi operator • Exponent encoder to compute the exponent of a 40-bit accumulator value in a single cycle • Two address generators, including eight auxiliary registers and two auxiliary register arithmetic units.ON-BOARD FEATURES:
• 4 Mbit (256Kb x 16) Flash Memory • 4 Meg (256K x 16-Bit) Static RAM for External Program/Data • 8 way DIP switch & LED • ON Board JTAG Emulator (XDS 100 version - 2) • PCM3002 AUDIO CODEC • Expansion connector for GPIO & Peripheral interface • On board USB for serial communication
Resistance Box, Plug Pattern
Description
All plugs are turned to a fine standard taper and are interchangeable. These are moulded in fluted plastic tops. The brass blocks are undercut and are fitted to a thick insulating plate. Heavy 4 mm brass terminals are used. Coils are non-inductively wound and are treated to be strain-free. Coil values are engraved on the plate and an infinity plug is also included. Accuracy ±0.5% for 0.01 to 0.05 ohm coils, ±1% for the rest 0.01 to 0.1 ohm, Total 0.2 ohm 0.1 to 1 ohm, Total 2 ohm 0.1 to 5 ohm, Total 11 ohm 0.1 to 10 ohm, Total 21 ohm 0.1 to 50 ohm, Total 111 ohm 0.1 to 100 ohm, Total 211 ohm 0.1 to 500 ohm, Total 1111 ohm 1 to 10 ohm, Total 20 ohm 1 to 50 ohm, Total 110 ohm 1 to 100 ohm, Total 210 ohm 1 to 500 ohm, Total 1110 ohm 1 to 1000 ohm, Total 2110 ohm 1 to 5000 ohm, Total 11110 ohmXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Simple Galvanoscope
Triangle Kit
Zooplankton Net
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Thin Cylinder Apparatus
A heavy bench top unit for studying the stress and strain in a thin walled cylinder under internal pressure. A thin walled cylinder is mounted between two support blocks. Internal pistons and seals create oil sealing. A handwheel at one end of the apparatus enables the cylinder end conditions to be adjusted to either open or closed. The internal pressure is adjusted by means of a hydraulic hand pump on the apparatus. An analogue pressure gauge displays the internal pressure whilst a pressure transducer gives feedback to the Data Acquisition Interface and Software supplied. Strain gauges are arranged on the external surface of the cylinder to measure the radial and circumferential surface strain. The strain gauges are at various angles.
Tuning Forks Set, Even Frequency
Resonance Apparatus
Transducer Trainer
Specification
• RTD acts as a temperature sensor • Strain gauge based load cell • Linear variable resistive transducer • LDR, Photo diode, photo transistor • Precision servo potentiometer • Inductive type proximity sensor • Heat source, Filament lamp, Buzzer • 3½ digit LED display • Analog type 10V Center-Zero meter • Inverting and Non-inverting amplifier • Amplifier with Gain and offset control • Instrumentation and summing amplifier • Low pass filter • Precision Rectifier • Timer and buzzer oscillator • Electric switchXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
CNC Lathe Trainer2
CONTROLLER:
SIEMENS / FANUC Main Spindle Drive : AC Motor with VFC Z and X Drives : Stepper drive with Servo Motor Input to Servo : Optically lsolated Motor Drive : Smart & Intelligent Run Speed Control : Through Controller Interpolation : Linear/Circular /parabolic Cycles Used : G, M, S, T, F, I, K, M, F, Circular interpolation / Canned Threading : Straight / Taper Power Devices : Short Circuit and over Temperature Protected, Single Phase Protection Real Time Toolpath Simulation : ProvidedMACHINE DETAILS:
Center Height : 150mm Swing over Carriage : 125mm Distance between Centre : 825mm Weight : 1100kg Dimension in mm : 2000 x 1200 x 1700 Rapid Travel : 5000mm/min Resolution Z Axis : 1 micron Resolution X Axis : 1 micron (Dia.) Automatic Lubrication : Provided Tool Changer : Automatic – 4 station SPINDLE Spindle Speed : Continuous Variable Spindle power : 3 HP Inside Taper : MT4 Speed Range : 50 to 1800 RPMAXIS TRAVEL:
X Axos : 120mm Z Axis : 800mm
Balance Spring
Model of Compound Microscope (BI STU)
Plate Type Heat Exchanger Apparatus
The unit consists of a plate type heat exchanger, in which cold fluid is cold water and hot fluid is hot water, which is obtained from geyser. The inlet and outer connections of the fluids are positioned so as to make the exchanger counter flow type. Hot and cold fluids pass between alternate plates various measurements provided enables the students to determine heat transfer rate, LMTD, heat transfer coefficients and effectiveness of the heat exchanger.
SPECIFICATIONS:
1.Heat Exchanger- S.S. Plate heat exchanger wiles nos. of 200 X 400mm. 2.Geyser to obtain hot water – 3 KW capacity. 3.Calibrated water flow measuring vessel 4.Thermometers to measure inlet and outlet temperatures of fluid. 5.Flow controls valves. A technical manual accompanies the unit.OPTIONAL ACCESSORIES:
Rotameters to measure water flow rates instead of measuring vessel. Multi channel digital temperature Indicator to measure the temperatures instead of thermometers.SERVICES REQUIRED:
1.Floor space 1.5m. X 1m, 2.230V, 15A, AC supply with earthing connection, 3.Water supply at the rate of about 10 lit/min at constant heat.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Tilt Telescopic Collapsible Steering System
Tilt, Telescopic & Collapsible Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Female Catheterization Training Simulator
Description
With the female catheterization trainer, female bladder catheterization procedures can be realistically demonstrated, practiced and assessed. The genital inserts are placed into the anatomically correct lower abdominal model and held in place with magnets.The material is soft and flexible:
the foreskin is movable and the penis can be stretched. The material gives a realistic feeling when inserting and removing the catheter into the bladder with realistic resistance and insertion depths.Direct learning:
When the catheter has been correctly inserted, fluid runs out, just like with a real patient. The catheter can also be checked through the transparent bladder. The abdominal wall can be removed so that the process can be viewed better.Includes suprapubic catheter:
If it is no longer possible to carry out catheterization through the urethra, a suprapubic catheter can be inserted. On the PRO version, a suprapubic catheter has already been put in place, and the student can practice cleaning it and taking care of it with the trainer.All the benefits of the female catheterization simulator at a glance:
Female catheterization with realistic resistance Soft and movable labia (for practicing disinfection, for example) Anatomically realistic pelvic structure Liquid outflow if catheterization is successfully carried out The transparent bladder can be checked and the abdominal wall can be removed. Includes suprapubic catheter for practicing, cleaning and caring for it. Stands securely on the table thanks to the non-slip feet Magnetic connectors for quick set-up and dismantling Easy to clean and maintain and can be completely taken apart A sponge on the inside prevents a build-up of moisture
Composite Walls Apparatus
Composite Walls Apparatus:
The apparatus consists of a pair of M.S. plates, Bakelite, brass/aluminum. These plates in series on either side of the heater form a composite wall. The whole unit is clamped in a frame, which can be viewed through the Perspex sheet. The thermocouple tapings enables us to find out the conductivity and resistance of the composite walls.
