XTEMOS ELEMENT
AJAX PRODUCTS TABS
Ultrasonic Transmitter And Receiver Set
This apparatus consists of a self-contained transmitter and receiver operating in the 40 kHz region. The transmitted wave is modulated at a user controlled variable frequency of about 2 kHz and this is detected by the receiver which amplifies the signal and drives a miniature integral loudspeaker. Both transmitter and receiver are contained in separate plastic enclosures measuring 175 x 100 x 40 mm which contain all the electronics and the 9 V batteries. The receiver has front panel 4mm sockets so that the output can be monitored on an oscilloscope for more quantitative measurements. The system is ideal for demonstrating sound waves above the hearing threshold and reflection properties associated with sonar etc. A special feature is the second transducer on the transmitter which can be switched on when required to produce two coherent sources. By moving the receiver along a line parallel to the two sources interference patterns can be dramatically demonstrated simplifying the Young’s slits experiment or enabling it to be demonstrated using waves other than light. Complete with batteries, full instructions and suggestions for use.
Spring Unit of Mechanical Model
Description
For showing potential energy in a wound-up spring and its conversion to electrical energy by driving a dynamo and lighting a lamp. May also be used to wind up a weight on a cord showing the change from potential energy to kinetic and back to potential in the raised weight. The steel shaft carries a clock spring with a free wheel device and winding ratchet, also an aluminium 'V' pulley 56 mm. diameter. One end of the shaft overhangs the base for use as line shaft when winding up a weight. Dimensions 220 x 100 x 100 mm. high Supplied complete with driving belt.
Thermocouple Calibration Test Rig
The Unit helps in calibrating given thermocouple for the range 0°C to 100°C. While calibrating, thermocouple is once dipped in ice for 0Q C and then in boiling water for 100°C. This is done till the thermocouple shows the actual temperature of ice (0° C) and boiling wafer (100°C) and a linear calibration is set. A mV meter is provided to know the corresponding voltage.
SPECIFICATIONS:
1.A digital mV Meter and a digital temperature indicator with 2 different type of thermocouples. 2.A water container with heater of 1 KW. 3.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Table surface area – 2 m X 1 m X 0.5 m height. 2.220V, 50hz. Stabilize Electric Power Supply. 3.Ice cubes – 0.5Kg. Approx.
Siemens IoT 2040 Gateway Based IoT Development System
SIMATIC IoT 2040 is an Industrial IoT Gateway, reliable open platform for collecting, Processing and transmission data. It helps the students to get the industrial IoT experience and develop Industry 4.0 Projects rapidly.
Specification:
• IoT 2040 Gateway - PLC and sensors of many brands can be integrated through Ethernet & Serial ports. - Open Protocols: Modbus, Profinet, REST or MQTT, AMQP, OPC UA - Based on Intel Quark X1020 ,(x86)@400MHz - Compatible With Open Source Software Arduino IDE and Yocto Linux - High level language support : Java, Python, C/C++ - 1 GB RAM, 8MB Flash ,256KB SRAM - Micro SD card Slot up to 32GB - One miniPCIe Slot for hardware expansion for WLAN/Additional Ethernet Port - Arduino Uno – R3 Compatible - Intel Wi-Fi + Bluetooth Module for 300MB data rate - 2xRS232/422/485(Switchable) - 1xUSB Controller + 1 x Device - 2 x 10 /100 Mbps Ethernet RJ45 • 5 types of sensors such as Temperaturesensor, LDR sensor, Motion sensor, Humidity sensor, Magnetic sensor included to • interface with IoT2040 & add on modules of IoT2040 • The IoT 2040 Gateway can communicate with PLC, DCS using profinet or OPC UA. • Analog Inputs are terminated in a SP7 patch connector • 4Nos of Digital Input SPDT Switch • 4Nos of user LEDsXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
ANALYTICAL BALANCE
 DESCRIPTION
- Student Physical Balances with flat beam.
- Chemical Balances with Flat beam and rider using facility.
- Chainomatic Analytical Balances with external alteration of weights up to 100 mg.
- Analytical Balances with Triangular beam with rider using facility / Flat beam with vernier scale.
- Capacity 1mg to 100gms
- Capacity 1mg to 200gms
- IDDC Certified & Tested, 100gm
- Capacity 1mg to 500gm
- 1gm
- 2gm
- 5gm
- 10gm
- 20gm
- 50gm
- 100gm
- 200gm
Car Chassis Rear Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM:It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Burner Bunsen – Semi Micro
Minerals Collection
Description
A quality collection of minerals, in wooden box, with partitioned tray containing 30 specimens, each numbered and enclosed in transparent plastics bag. Specimens may be removed from bags for detailed examination. Each speciman is labelled also on the inside of the box lid, indicating the geological name.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Heart Models
Our capability and industrial know how has enabled us to manufacture, supply and export Heart Models.
Made of superior quality raw materials that are supposed to be the best in the market, these products have a descriptive structure and construction.
With clear depiction of external features and internal structures of the heart, these provide an appropriate indication of various large blood vessels.
These products help in education medical students about the clearer conception of the routes of the systemic and pulmonary circulation in the heart.
Heart Models are packed in special packaging material so as to ensure its safe and secure transit.
Vacuum Assisted Hydraulic Drum Brake
Vacuum Assisted Hydraulic Drum Brake With Vacuum Booster & Motorised Vacuum Pump
Suitably sectionised full size unit. Consisting of original parts such as :- vacuum booster with master cylinder assembly, wheel cylinder, brake shoes, brake drums, motorised vacuum pump and necessary connections. Completed with operating lever and mounted on heavy iron stand.
Steam Engine Model
Rear Axial Assembly With Differential Gear Semi
Rear Axial Assembly With Differential Gear Semi Floating Type – Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Mammal
Ticker Tape Timer 12V
Ticker Tape Timer 12V
These devices use an electromagnet which activates a striker, producing dots via a carbon disk on the ticker tape.
With 4mm terminal sockets.
The dots are produced at a rate of 50 - 60Hz depending on the mains frequency.
There are 6V and 12v units available.
The Ticker Tape Timers are used in the measurement of velocity, acceleration and general timing.
2 Stroke Diesel Engine Sectional Working Model
Karl Fisher Titrimeter
Description
Auto Karl Fischer Titrimeter – 761 is an automatic apparatus designed to carry out Karl Fischer Titrations for accurate determination of moisture content in various samples. The instrument comprises of two units i.e CONTOL UNIT & TITRATION UNIT. The CONTROL UNIT controls the complete automatic titration. On pressing the START button, the titration starts and the KF reagent is added automatically from the burette, through a solenoid valve into the titration vessel. As soon as the end point is reached, the titration is stopped automatically by the Control Unit. It has fully solid state circuitry incorporating advanced IC technology. Titration unit contains the magnetic stirring mechanism and the solenoid valve assembly. The cabinet is designed to serve as a titration stand. Karl Fischer method for determination of moisture content is used in pharmaceutical and drug manufacturing industries, food stuff, sugar, wood, paper and textile industries, petroleum refineries, chemical and fertilizer units etc.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Laboratory Timer
This is a versatile timer quartz crystal controlled for very high accuracy.
which can be used for conducting experiments related to timing and motion with high accuracy.
Can be used for G by free fall liner air tracks, dynamic trolleys etc.
This timer has an in built power supply for the coil for G by free fall apparatus and lamps for photo gates.
Range : 0.001, 0.01, 0.1 Sec.
The above timer has a built in power source for photo gates and the coil for 'G' by free fall apparatus.
Motorised Governor Apparatus
The unit consists of a base upon which the bearing holders and driving motor are bearing can be fitted in a holders to end conditions for test shafts, viz. Both end fixed and one end free, one end fixed. A Variac provided control of driving motor. The unit demonstrates the phenomenon of whirling of shafts with single rotor. As the test is destructive, after the test cannot be used, hence the unit only demonstrates the principle.
However, results obtained are closer to theory, as compared to those with bare shafts. Also, It can be demonstrated that, after passing whirling speed, shaft again starts running true.
SPECIFICATIONS OF MOTORISED GOVERNOR APPARATUS:
1.Test shaft – 4.75 mm, 6.35 mm and 7.9 mm – 2 each. 2.Bearing to provided end conditions, (a) Both ends fixed, (b) One end fixed and one end free. 3.Drive motor 1/8 HP, 1500 rpm with control arrangement. 4.The whole unit is mounted on a sturdy base. 5.Rotor for each shaft of suitable size. 6.A technical manual accompanies the unit.SERVICES REQUIRE FOR MOTORISED GOVERNOR APPARATUS:
Floor space area of 2m. X 1m. at working height. 230V, 15 A, AC electric supply connection.
Hot Air Oven
| Specification | : | Hot air oven, 2 shelves |
|---|---|---|
| Technical Specifications | : | |
| Inside Body | : | Stainless Steel |
| Out Side Body | : | MS Powder coated with stove enamel paint. (SS body also available) |
| Number of Selves | : | 2 Adjustable Perforated Selves. |
| Body Structure | : | Double Walled structure filled with glass wool insulation |
| Number of Heaters | : | 2 x 1000 Watts |
| Heater Quality | : | High Quality Chrome Heater insulated with ceramic beads |
| Air Circulation | : | By Air Circulating Fan to ensure even temperature distribution. |
| Ventilation | : | Ventilation port with adjustable Opening. |
| Temperature Control | : | By Digital Temperature indicator and Controller |
| Temperature Display | : | Digital Temp. display |
| Range of Temperature | : | Ambient to 250ºC |
| Accuracy | : | 0.10C |
| Least Count | : | 1.0C |
| Power | : | 220 Volt AC 50 Hz. Single Phase |
| Sizes available are | : | 12" x 12" x 12" (28 Ltr.)14" x 14" x 14" (45 Ltr.)18" x 18" x 18" (95 Ltr.)24" x 24" x 24" (224 Ltr.) |
Storage Vial (O Ring)
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
2 Axis Robotic-MatlabTrainer
This Robo Trainer is working along with Matlab. Two axisrobo consists of two AC Servo Motors which are made to rotate using PWM pulse output of the controller. Two rotational encoders are present to determine shaft position of the motors. One AC Motor is used to rotate the handle from 0 to 360°, and the other is to move the handle up and down which can cover a distance of 450 mm. Pneumatics ARM is used for the application of pick and place of an object.
Specification
• Horizontal Handle Rotation - AC servo Geared motor - 500 rpm - 0 - 300º Rotation • Vertical Handle Rotation - One AC servo Geared motor - 500rpm - 450mm Movement • Pneumatic Gripper - 12mm Bore Diameter - 25mm Stroke Length - Miniature cylinder type - 1kg Pay load
JUMBO CONDENSER CLAMP
PRODUCT DESCRIPTION
4 Fingers covered with Silicon Sleeves, Jaws do not cross over; can hold upto 125 mm. dia. with 300 x 10 mm. C.P. rods. Brass casted, Chrome Plated.
AVAILABLE IN DIFFERENT TYPES:
-
- Jumbo 3 Finger Clamp (Aluminium Casted)
- Jumbo 4 Finger Clamp (Aluminium Casted)
- Jumbo 4 Finger Clamp (Brass C.P )
- 3 Finger Clamp with two keys independently operated (Al.Casted)
- 3 Finger Clamp with two keys independently operated (Brass C.P)
Transistor Char Appt
Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when an unknown printer took a galley of type and scrambled it to make a type specimen book. It has survived not only five centuries, but also the leap into electronic typesetting, remaining essentially unchanged. It was popularised in the 1960s with the release of Letraset sheets containing Lorem Ipsum passages, and more recently with desktop publishing software like Aldus PageMaker including versions of Lorem Ipsum.
Utility Tray
We excel in providing high quality Utility Tray to our valuable clients.
Our range of Utility Tray is well appreciated in the market for its high quality and durability.
this Polypropylene Tray can be utilized for wide range of purposes ranging from drying glassware to sterilizing and for storing any laboratory apparatus.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Utility Tray 375 x 350 x 130 mm | 6 |
Separating Throttling Calorimeter
AIM
To find out dryness fraction of steam by combined separating and throttling calorimeter.
