XTEMOS ELEMENT
AJAX PRODUCTS TABS
Forceps (Different Types)
Refrigeration Air Conditioning Tool Kit
Water Table Model
Window Air Conditioning Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Mosquito Breeder
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Sterling Engine Working Model
The Stirling engine was invented by Robert Stirling, a Scottish minister, in 1816. A Stirling engine is a heat engine that operates by cyclic compression and expansion of air or other gas, the working fluid, at different temperature levels such that there is a net conversion of heat energy to mechanical work.
Formation Of Rocks
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
3Ø – 3Ø Matrix Converter
FEATURES:
• 9 No. Bi-directional Switch with IGBT and Fast Diode Bridge,Rating@1200V 50A Forms 3 Phase to 3 phase Matrix Converter Power Circuit • Output of Matrix Converter Terminated by Banana Connector in the Front Panel • 9 No. High Speed Opto- IC Provided for Gate PWM Isolation. • 9 No. Single Channel IGBT Driver IC with Current Limiting Facility Provided for IGBT Gate Driving. • 9 No. 15V DC Power Supply Provided Internally for Control Circuit. • 3 No. Inductor and AC Capacitor Provided for Three Phase Input Filter. • One No Three Phase Synchronizing Transformer (230/9V) Provided for three Phase Supply Synchronization • 6 nos Hall-effect Current Sensor with Signal Conditioning Circuit Provided for Output and Input Current Measurement and Protection. • AC voltmeter is provided for measure the input AC voltage. • +/- 15V DC Internally Provided for Sensor Signal Conditioner Circuits. • MCB Provided for Input power ON/OFF and OL Protection ON/OFF Switch. • Test points are provided on the front panel to measure the voltage, current and PWM signals • 34 pin FRC Connector Provided for IGBT Gate PWM Inputs. • Input : Three Phase 440V AC, 50 Hz. • Output : Three Phase Variable Voltage, variable frequency • Rating : Suitable for 1 HP 3Ø AC Induction Motor
Ultrasonic Interferometer
Ultrasonic Interferometer is a simple and easy to use unit for the accurate measurement of ultrasonic velocity in a Liquids and Liquid systems at the desired temperature (and at desired frequencies).
FEATURES:
• Accuracy in wavelength measurement – 0.01mm • Digital Panel Meter ( DPM) for observing the change in the reading between nodes /anti nodes (75mV approximate between a node and anti node) • Easy replacement of transducers with other frequency • Only one Liquid cell is required for all frequencies • Built in IC regulated power supplies. • The frequency of the Crystal oscillator at the piezo electric transducer is so matched at the 3 digit Decimal accuracy • The accuracy of Meter is 3 Digit Decimal • Stainless Steel based mechanical setup.ACCESSORIES:
• Liquid cell - One (with provision for water circulation) • Transducer (Longitudinal, 2MHz) - One • Micrometer assembly - One (with Tx)
Automatic Knife Sharpener
Description
Portable, precision automatic knife sharpener with timer 0-60 minutes to adjust sharpening time. This equipment can sharpen all microtome knives up to 140 mm in length. Complete with one universal holder, two honing plates, one bottle honing glass compound, one knife inspection block and one re-dressing pad but without micro abrasives.
Sliding Mesh Gear Box
Sliding Mesh Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Rain Gauge
Description
Rain gauge is designed to measure the precipitation. This small Version consisting of upper and lower housing part, measuring cylinder; Housing made of stainless steel, orifice rim made of brass. Type 7019.0000 can be supplied with a receiving area of 100 cm2. (This type is not conforming to meteorological standards). • Receiving area : 100 cm². • Rain measure (graduated glass) : 250 cm³. • Measuring range : 0 t0 25 mm precipitation (relative to a receiving area of 100 cm²). • Graduation : 1/1 mm precipitation. • Dimensions : dia 115 mm; height 300 mm. • Weight : approx. 0.8 kg.
400W Smart Grid Experimental Setup
This consists of 2 Microgrid, one 400W& 200W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. 3Φ, 1KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 1KVA Grid Connected Solar Power Inverter can be added to this experimental setup. By adding 1KVA commercial solar inverter, when the experimental setup is not used by student, it could be used to generate power.
This Advanced Smart Grid Experimental Setup Consists of
• 2 Micro Grids, 400W& 200Wof Power Generation using Solar, Wind or Hybrid • An Isolation Transformer coupled to the utility grid, acts as main grid to this Setup • Commercial 1KVA Grid Connected Inverter with Solar Panel (Optional) • Optional Components for the 400W Smart Grid Setup • DSP/FPGA Controller for PE, SG, PS Applications • IoT Based Data Acquisition • Other Add onsMicro Grid - I (Solar/Wind Grid Connected 1Φ, 400W Smart Micro Grid)
• Main Frame • 200W Solar PV Module with Stand • 200W Wind Turbine with Tower (Optional) • 30W Wind Turbine with Blower setup • 200W DC-DC Boost Converter for Solar • 200W DC-DC Boost Converter for Wind • 400W Hybrid DC-DC Buck-Boost Converter • Battery Bank • 400W Inverters • Bi-Directional Buck-Boost Converter for Battery Charging • DSP/FPGA Controller • Microcontroller based Protection Relays • Smart Energy Meter • Synchronizing Panel • Single Phase R Load & Lamp Load (200W) + (200W) • PLC with SCADA Software • 8 Channel, PC based Power Quality Analyzer (Optional)
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Fertilization Process Simulator
Orsted’s Apparatus
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Electrical Power Steering System Actual Working
Electrical Power Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Crucible with Lid Low Form
Description
Chemical porcelain crucibles are glazed inside and out, except outside bottom and rim. Crucible covers are completely glazed except for rim. For use in temperatures up to 1150 C (2102 F). Not recommended for minerals or metals.Capacity :
250mlHeight :
2.36 inch (60mm)Top Outside Diameter :
4.02 inch (102mm)
Pelton Wheel Turbine Test Setup
DESCRIPTION:
Pelton Wheel Turbine is only impulse water turbine now in common use named in honor of Sir L.A. Pelton (1829-1908) of California, USA. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the Inlet of the Turbine is only kinetic energy. The Pressure at the Inlet and Outlet of the atmospheric. This turbine is used for high heads. The Present Set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through SS nozzle with a SS spear, by means of Centrifugal Pump, tangentially to the runner. Row of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel the runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is providing with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid MS structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure Gauge is fitted at the Inlet of the turbine to measure the total supply head to the turbine.EXPERIMENT:
1.To study the operation of a Pelton Wheel Turbine 2.To determine the Output Power of Pelton Wheel Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 111 (1.33 HP) | HM 111 (2 HP) | HM 111 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1.5 Kw | 5 HP / 3.75 Kw |
| Discharge | 300 LPM (Approx.) | 400 LPM (Approx.) | 630 LPM (Approx.) |
| Supply Head | 25 m | 40 m | 45 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 150 Liters. | Capacity 200 Liters. | Capacity 300 Liters. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 7.5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1000 RPM (approx.) | ||
| Impeller | Material Brass, Bucket type | ||
| Nozzle | Material Stainless Steel/Mild Steel | ||
| Spear | Material Stainless Steel/Mild Steel | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
