XTEMOS ELEMENT
AJAX PRODUCTS TABS
Pressure Process Station
Panel Features
• Digital Panel Meters. • Mimic diagrams. • Pressure gauges are provided, wherever necessary.Softwares
• MATLAB • LabVIEW • PLC • C/VB CompatibilityFeatures
• The Pressure process station is an attractive module comparing to the Analyzer and Laboratory trainer. • All are the industrial standard (4-20)mA interfacing signals. • It provides a real industrial feeling of the process to the students. • A Piezo Resistive Pressure Transmitter (0-7)Bar is used to sense the pressure. • An Electronic Regulated Power supply is fixed for voltage Regulation. • An electro pneumatic converter is mounted to control the pneumatic control valve. • A globe Pneumatic Control Valve for controlling flow of air. • An air regulator cum filter is provided for Air regulation. • A two separate pressure tank is provided as process tank with pressure gauges and relief valves. • All the air flow lines are fitted by flexible hoses/fittings for better reliability. • Hand valve provisions are given for series, parallel connection of pressure tanks. • USB/Serial port data acquisition is provided.
Suspension Bridge Apparatus
DESCRIPTION:
Cables are frequently used to support loads over large spans such as cable stayed for suspension bridges, cable car systems and stadium roof. They are used extensively for permanent guys on structures such as microwave towers and derricks. They are also used for temporary guys during erection. The only force in a cable is direct tension. They are too flexible to carry any moment. A cable is used to carry concentrated loads, uniformly distributed load along its length and uniformly distributed load along the horizontal span. It takes the shape of a polygon under concentrated loads, a catenary under uniform load along its length (such as its own weight), and a parabola under uniform load along the horizontal span.EXPERIMENT:
• Study the Extension of each spring Balance Left & Right Both. • Study of the effect of a point loadTECHNICAL SPECIFICATION:
• Apparatus Consists of two mild steel cables 0.5cm diameter in cross section and 150cm long, pinned to two supports 90cm apart situated symmetrically. • One of the ends can be converted to a roller by applying a known load at the end with the help of suspended pulley system. • Vertical loads can be applied at various points along the span of the beam. • A dial gauge with 25mm travel (with a magnetic base) is to be supplied with the apparatus complete with a supporting stand and a set of weights.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Optical Bench, Junior
Description
On wooden base, with 1.5 meter scale, with six sliding bases. Each siding base is with an index mark, a brass pillar and locking screw, with following accessories: 1. One lamp house with 230 V lamp. 2. One object screen, metal, white. 3. One lens holder for 38 mm diameter Lenses. 4. One receiving screen, metal, white, with slot for squared paper on reverse. 5. One object needle, mounted in brass rod. 6. One plane mirror in metal frame. Each of these accessories is mounted on a 6 mm brass rod which fits into the pillars and is adjustable for height.
Hydraulic Trainer Electrohydraulic
Silent Features:
1. software for simulation of Hydraulic circuits. 2. We are manufacturing cylinders for industrial applications. Our cylinders can withstand pressure up to 160 Bar. 3. Mobile and self-contained unit, only electrical connections are required. 4. Simplicity of operation and designed for amateur use. 5. Two pressure relief valves are provided in the system. One is provided inside the tank to increase the safety. 6. Hoses can withstand pressure of 188 Bar. 7. Test Pressure : 80 Bar ; Operating Pressure : 40 Bar. 8. Realistic Industrial circuits are demonstrated. 9. Special Bell housing is provided to maintain the Run out between Pump and Motor below 0.020mm. 10. Special fixtures used for pipe bending and ferrule fitting arrangement. 11. Specially designed front mounting plate. 12. System is flushed with very high velocity (4 times the working pressure) by separate oil which maintains class A cleanliness of system. 13. Lowest pressure drop in the system to avoid overheating. 14. Cylinder are manufactured from precision honed tubes, hardened ground, hard chrome plated piston rods and imported quality seals
Spring Unit of Mechanical Model
Description
For showing potential energy in a wound-up spring and its conversion to electrical energy by driving a dynamo and lighting a lamp. May also be used to wind up a weight on a cord showing the change from potential energy to kinetic and back to potential in the raised weight. The steel shaft carries a clock spring with a free wheel device and winding ratchet, also an aluminium 'V' pulley 56 mm. diameter. One end of the shaft overhangs the base for use as line shaft when winding up a weight. Dimensions 220 x 100 x 100 mm. high Supplied complete with driving belt.
Refrigeration Trainer General Cycle Type
The unit consists of vapor compression refrigeration cycle provided with components normally used in refrigeration system so that student can get familiar with the components. Various measurement provided enable students to estimate the performance of the system.
SPECIFICATIONS:
1.Compressor- Hermetically sealed compressor, having capacity of 0.3 T. 2.Expansion Devices a) Thermostatic Expansion Valve b) Capillary tube. 3.Evaporator coil. 4.Controls: a) Services Valve b) Solenoid Valve c) Filter-Drier for refrigerant d) High/Low pressure cutout e) Thermostat. 5.Measurements: a) Thermometers (mercury in glass) – 4 Nos. b) Pressure gauges for condensing and evaporating pressure. c) Energymeter for compressor d) Voltmeter and Ammeter for compressor. e) Rotameter for liquid refrigerant flow measurement. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 1m x 2m x 2m height. 2.220V, I5Amp, Single Phase Stabilized power supplyXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Conical Percolator
Underground Mine Model
Tooth Hygiene Set
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
RAY OPTICS KIT
Phase Shift Keying Modulation and Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Phase Shift Keying Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supplies of ±12 V and ±5 V.
2. Built in Carrier wave Generator (Sine Wave) of 5 Vpp, 22 KHz ± 5% Frequency range with output on sockets.
3. Built in Data Generator using IC 7490 with four modulating signal outputs on sockets.
4. IC TL084 & IC 7486 are using for PSK demodulator.
5. Circuit diagram is printed on the milky white top panel and important connections are brought out on the sockets.
4 Stroke 4/3 Cylinder Petrol Engine
4 Stroke 4 Cylinder Diesel Engine – Motor Driven Actual Cut Section Working Model With Valve Timing Attachment
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine will be supplied with key card & very interesting literature regarding working.
Animal Cage Stainless Steel
Description
MAde of S.S. frame provided with thick S.S.mesh o sides. Hinged door on front,Provided with water bottle and feeding tray. Extra drawer provided in the base for collection of excreta. Feeding arrangement allows removal of bin from outside of cage with automatic drop closure. 60x45x60cm. 45x38x45cm.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Model of Astronomical Telescope
Stop Watches
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Refrigeration And Air Conditioning Components
Actual Cut Section – Display Board (Set Of 30)
This actual cut section model is a set of thirty components used in refrigeration & air conditioning. With the help of this model students can understand the working parts of the components used in refrigeration & air conditioning. This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Wooden Levelling Staff Telescopic type
Description
We bring forth an impeccable array of Wooden Leveling Staff to eminent customers. Products that we come up are ideally used to cater to the various needs and preferences of customers of various construction industry along with others. Therefore, this range is quality tested as per industry laid parameterst.
Projection Measuring Microscope
Specifications
The instrument is used for microscopy applications.The device is used to examine or view the specimens that can't observe with a naked eye. It is a dual-purpose testing device which is provided with the fine grain screen to observe the samples. The major difference between the base model and advanced model is the objectives that are provided with the device i.e. 5x, 10x and 20x. It is easy to operate instrument that offers highly accurate test results. The instrument is supplied complete with the vinyl cover in a packing of a cardboard box. The instrument provides high-quality and clear images.The instrument is provided with the fine grain glass screen with the magnification range up to 400X. It is a dual purpose instrument which is equipped with the halogen projection bulb. The works efficiently on the power supply of 220AC. The device is assembled with the effective cooling fan inside the instrument.
PCR Tube Rack
We are one of the prime Exporters and Traders of PCR Tube Rack .
Used for keeping PCR Tubes, Top & base of this rack are made of tough & transparent polycarbonate while the middle portion is made of polypropylene.
PCR Tube Rack facilitates the use of multipipetters.
A number of racks can be stacked together to save shelf space.
Material : Polycarbonate / Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| PCR Tube Rack (Rack for 96 PCR Tubes of 0.2 ml | 4 |
