XTEMOS ELEMENT
AJAX PRODUCTS TABS
Human Head And Neck L. S.
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
4 Stroke 6 Cylinder Petrol Engine V-6
4 Stroke 6 Cylinder Petrol Engine (V-6) Motor Driven Actual Cut Section Working Model
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine willbe supplied with key card & very interesting literature regarding working.
Six Phase Power Analyzer
Specification
• 6 phase measurement @ 50Hz • 6 voltage inputs (250V AC max., 50Hz) & 6 AC current inputs (5A max) • Zero crossing output for both voltage and current waveforms • 6Nos of phase sensing circuits provided to measure the phase difference of 2 waveforms • Signal Conditioning for Torque & Speed (QEP, Proximity, Optical) • After Signal Conditioned, 6 voltage outputs, 6 current outputs, 12 zero crossing outputs & 6 phase sensing outputs are terminated at 34 pin and 26 pin FRC connectors • Power input through banana sockets • Housed in a sleek cabinet
Pole Holder
Description
We are supply of high quality Pole Holders for prisms. These have been manufactured using the finest quality of aluminium and brass, in order to ensure their strength and durability. We provide the poles in the shape of a tripod for increased sturdiness while holding prisms and other survey instruments. We also offer customization and can supply these products in accordance with the demands of our clients.The specifications of the Pole holder :
• Manufactured using fine quality aluminium and brass • High on parameters like strength and durability • Improved sturdiness while holding survey instruments
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Rear Suspension System
In this model the working of rear suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a rear suspension system are shown in actual working form. This model helps the student to understand the working of the rear suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Leaf Spring Type Suspension System With Rear Rigid Axle
(B) Rear Independent Type Suspension System
Electromagnet
Candle Holder
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Air Conditioning Trainer General Cycle Type
The unit consists of ducting fitted with various air conditioning components. Airflow is generated by an axial flow fan and in the airflow, heaters, cooling coil and steam humidifier connection is provided. Cooling circuit consists of a hermetic compressor; air cooled condenser, thermostatic expansion valve and evaporator (i.e. cooling coil). Measurements of various parameters Torn cooling cycle and heating cycle are provided and students can easily visualize and understand the basic principles of air conditioning.
SPECIFICATIONS:
1.Cooling circuits – It consists of: a) Hermetic compressor, having the capacity of 2/3 ton of refrigeration (approx.) using R-22 refrigerant. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for high and low pressure. d) Prescott (i.e. high and low pressure cut-out). e) Thermometers for temperature measurement at various points In the cycle. f) Energymeter for compressor input measurement. g) Condensate measuring arrangement. 2.Heating Circuit – Air heaters with input control provided with energymeter for input measurement. Maximum heating capacity 1 Kw. 3.Steam generator and injector for humidification of air. All above components are connected to a duct of size 200mm. X 200mm. in which airflow is generated by axial flow fan. 4.Anemometer for measurement of air velocity, (range 0-15 m/sec. Following experiments can be conducted on the unit a) Cooling of atmospheric air. b) Heating of atmospheric air. c) Humidification of atmospheric air. d) Dehumidification and heating of atmospheric air. (Cooling coil acts as dehumidifier at reduced airflow.)SERVICES REQUIRED:
1.440 V, 15 A, 3 Phase supply with earthing connection. 2.Floor space area about 3 m. X 2 m.
Rotary Pipette Stand
Moulded in Polypropylene, the unique Rotary Pipette Stand holds a maximum of 94 pipettes and rotates on a central vertical axis for convenient selection of any particular pipette.
The lower rotating disc has four concentric troughs with tapered sides and open bottoms that cradle the pipette tips protectively and permit water drops to run off.
The upper disc has a grid pattern concentric with the bottom disc and keeps the pipettes vertical.
Liquids draining off the pipettes are retained on the top of the stationary base by the outer ring.
Our Rotary Pipette Stand can be easily disassembled and reassembled.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pipette Stand (Rotary) - For 94 pipettes | 1 | |
| Pipette Box | 4 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Burner Bunsen – Simple, LPG
Dissecting Microscope
Specifications
Microscope with round base is designed for greater stability. Having joint revolving arm for moving the magnifying lens over the stage allowing the whole stage are to be scanned. Focussable by Rack and Pinion. Detachable rests on either side of the stage provided steadying support for hands during fine dissection. Illumination by plano concave mirror in fork mount. With dust cover duIy packed in styofoam case. (Wooden Box optional).| Drawtube | Monocular | |
| Eyepiece | 10X | |
| Objective | 4X |
Trans-Ratio
Description
Trans-Ratio is a simple transformer system that allows students to investigate the relationship between primary voltage, secondary voltage and the turns ratio. The Primary coil has tappings at 200, 400 and 600 turns while the Secondary has 100, 200, 300, 400, 500 and 600 turns all brought out to 4mm sockets. An AC supply of upto 6 V as well as AC voltmeters are required for demonstration purpose.
Triangle Kit
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
4 Stroke 6 Cylinder Diesel Engine
4 Stroke 6 Cylinder Diesel Engine – Motor Driven Actual Cut Section Working Mode
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine willbe supplied with key card & very interesting literature regarding working.
REAGENT BOTTLE Wide mouth
PRODUCT DESCRIPTION:
Reagent Bottle, Clear, Wide Mouth, Glass Stopper, Soda-lime Glass.
Reagent bottle has a soda glass body, a ground glass stopper, and a wide pour lip. This bottle has a wide mouth for easy filling, and it is used to hold fluids that can have a solvent or chemical reaction. The ground glass stopper seals the bottle to secure contents and help prevent spills and evaporation. This bottle is suitable for use in mixing and storing samples, liquids, and reagents.
Lab bottles are suitable for use in chemistry and biology applications, as well as in pharmaceutical and scientific testing.
Size:
60ml
125ml
250ml
500ml
1000ml
CNC Lathe Trainer1
CONTROLLER:
Type of control system: PLC based system Main Spindle Drive : AC Motor with VFD Z and X Drives : Stepper drive with RAMP function Input to Stepper Motor : Optically Isolated Motor Drive :TTL Compatible Run Speed Control : Computer controlled through software Interpolation : Linear / Circular / Parabolic Cycles Used :G,M,S,T,F,I,K,M,F Cycles : Circular Interpolation / Canned Threading : Straight / Taper Power Devices : Short Circuits and over Temperature Protected Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
Center height : 100mm Swing over Carriage : 80mm Distance between Centre : 250mm Longitudinal Travel : 250mm Weight : 350 kg Dimension in mm : 1100 x 750 x 1700 Rapid Travel : 500mm/min Resolution X & Z Axis : 10micron Dt. Motor Power : 40V – 4A Lubrication : ManualSPINDLE:
Spindle Speed : Continuous Variable Spindle Power : 1.5 HP Inside Taper : MT3 Speed Range : 100 to 3000 RPM
Accessories Set For Demountable Transformer
Description
Comprising 1 welding coil of 5 turns on former with insulated handle and short-circuiting pins,1 annular melting trough with insulated handle to show heating by induction,1 jumping ring which is thrown clear when primary current is started and a floating ring which remains freely suspended when primary current is flowing.
400W Smart Grid Experimental Setup
This consists of 2 Microgrid, one 400W& 200W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. 3Φ, 1KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 1KVA Grid Connected Solar Power Inverter can be added to this experimental setup. By adding 1KVA commercial solar inverter, when the experimental setup is not used by student, it could be used to generate power.
