XTEMOS ELEMENT
AJAX PRODUCTS TABS
TDS Meter
Human Larynx With Tongue
Description
Natural size, three parts. Larynx showing cartilages, ligaments, muscles, relief of mucous membrane and thyroid gland. Tongue showing front part of the lower jaw which is detachable and separates into two parts, median section, sublingual gland and sub mandible gland are shown. on base with key card.
Animal Cage
Description
Made of iron S.S frame provided with thick iron mesh on sides. Hinged door on front. Provided with water bottle and feeding tray. Extra drawer provided in the base for collection of excreta. Well painted for elegant looking Feeding arrangement allows removal of bin from outside of cage with automatic drop closure. Size 30x23x30cm Size 45x45x38cmXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Model of Compound Microscope (BI STU)
TI MSP430 Development Board
ON Chip Features
• CPU - MSP430F1611 • Core - 16 bit RISC Architecture. • Speed - Up to 8 MHZ. • Flash - 48 KB + 256B. • SRAM (on-chip) - 10KB. • 48 GPIO Lines. Two UARTs. • One I2C Module. One SPI Module. • Two 16 bit Timers. • Five Power Saving Mode. • 12 bit ADC with single channel. • 12 bit DAC with two channel.ON Board Features
• Eight Digital Output - LED Interface. • Two Digital Input. • 16 x 2 Character LCD Interface. • 7 Segment Display via I2C Interface. • 10 Base T Ethernet Connectivity. • SD Card Interface Support. • Audio Interface. • Jtag connector is provided for Debugger. • USB to serial interface provided.
Power Steering Trainer System Actual Working
Power Steering Trainer System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Wheatstone Bridge, Two Gap
Description
Comprising a resistance wire swg 24 stretched along a meter scale subdivided in mms and marked every cm. is clamped to stout brass plates so as to avoid end errors. A plated brass strip with 4 mm socket terminal is fitted along the meter rule to provide a two gap system for normal Wheatstone bridge work. Complete with jockey.
Jockey
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
400W Smart Grid Experimental Setup
This consists of 2 Microgrid, one 400W& 200W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. 3Φ, 1KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 1KVA Grid Connected Solar Power Inverter can be added to this experimental setup. By adding 1KVA commercial solar inverter, when the experimental setup is not used by student, it could be used to generate power.
This Advanced Smart Grid Experimental Setup Consists of
• 2 Micro Grids, 400W& 200Wof Power Generation using Solar, Wind or Hybrid • An Isolation Transformer coupled to the utility grid, acts as main grid to this Setup • Commercial 1KVA Grid Connected Inverter with Solar Panel (Optional) • Optional Components for the 400W Smart Grid Setup • DSP/FPGA Controller for PE, SG, PS Applications • IoT Based Data Acquisition • Other Add onsMicro Grid - I (Solar/Wind Grid Connected 1Φ, 400W Smart Micro Grid)
• Main Frame • 200W Solar PV Module with Stand • 200W Wind Turbine with Tower (Optional) • 30W Wind Turbine with Blower setup • 200W DC-DC Boost Converter for Solar • 200W DC-DC Boost Converter for Wind • 400W Hybrid DC-DC Buck-Boost Converter • Battery Bank • 400W Inverters • Bi-Directional Buck-Boost Converter for Battery Charging • DSP/FPGA Controller • Microcontroller based Protection Relays • Smart Energy Meter • Synchronizing Panel • Single Phase R Load & Lamp Load (200W) + (200W) • PLC with SCADA Software • 8 Channel, PC based Power Quality Analyzer (Optional)
Structure of bone model
SAFETY GOOGLES
PRODUCT DESCRIPTION
- Economical goggle offers indirect venting and anti-fog coating for reduced fogging
- Polycarbonate lens absorbs 99.9 percent UV
- Meets the high impact requirements of ANSI Z87.1-2010 Standard
- Sturdy polycarbonate lens wide opening to fit over prescription eyewear
- Protective splash goggle clear lens
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Air Conditioning Trainer Window Type
Window air conditioner is becoming now a day’s necessity. The unit demonstrates the application of window air conditioner & evaluation of its performance. It consists of a small room to which a small air conditioner is connected the room is provided with a transparent front cover with a heater inside to simulate heat load in the room. Various measurements are provided so that performance of system that is COP of system, actual & theoretical cooling capacity of system & power consumption of unit with different load conditions.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirloskar make, having the capacity of 1/10 ton of refrigeration using R-12 refrigerant to keep room temperature between 20 to 30 c. 2.Condenser – Finned tube type, with forced air flow over the tubes, 3.Capillary tube of matched length as expansion device. 4.Evaporator – Finned tube type with forced air flow, 5.Room – 0.6 X 0.7 X 0.7 m. height, provided with transparent front wall. A heater with input control is provided inside the room. Which simulates different load conditions. 6.Measurements and Controls a) H.P. / L.P. Pressure gauges b) Digital temperature indicator to measure the temperatures at various points. c) Energy meters to measure input to compressor & heater. d) High and low pressure cutout. e) Thermostat to put off the compressor at set room temperature. f) Necessary switch for electrical components.SERVICES REQUIRED:
1.Floor area of 2m X 1 m. 2.230V, 15AC stabilized supply with earthing connection
Transmission Line Trainer
This trainer is designed for study of co-oxial cable characteristics like Impedance measurement, VSWR measurement etc., It is based, i) The latest technology of DDS Based RF source. ii) Directional coupler for VSWR Measurement. iii) TDR to measure the cable fault.
Specification
• DDS RF Source - Frequency: 10 to 400MHz. - Step Size: 1KHz. - Direct Digital Synthesis (DDS) Method Based. - Since DDS Device is primarily digital, it offers. • Display: Graphics LCD display of 240x128 pixels with backlight to plot VSWR, TDR characteristics etc., • One directional coupler provided for VSWR, Return loss measurement. • In-Built RF Detector for 10-400MHz Frequency range. • In-Built TDR (Time Domain Reflectometer) to measure and study nature of discontinuation in the co-axial cable. • Output Impedance: 50 ohms. • Co-axial cable: Various lengths of 50 ohm, 75 ohm cables supplied. • All relevant waveforms are displayed graphically in the Graphics LCD
Human Head And Neck L. S.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Magnetic field demonstrator
Description
Consist of a closed transparent box with a transparent tube through the center. The box contains iron filings and silicon oil. When one or more cylindrical magnets are inserted into the central tube, the filings are attracted and line up along the field lines in all dimensions With Cylindrical Magnet.
Heat Pipe Apparatus
Heat Pipe Apparatus:
Heat pipe is an interesting device, which is used to transfer heat from one location to another.
The apparatus consists of three pipes, viz. A heat pipe, copper pipe and stainless steel pipe. Ail the pipes have same physical dimensions. Copper and stainless steel pipes serve the purpose of comparison of heat pipe performance. All pipes are mounted vertically with a band heater at lower end and water filled heat sink at upper end. Nearly isothermal operation of heat pipe is clearly visualized from longitudinal temperature distribution of the pipe.
SPECIFICATIONS:
1.Heat pipe – Stainless Steel pipe, 25 mm O.D., 450 mm. Long. Sealed at both ends, evacuated and filled partially with distilled water – one No. 2.Copper and stainless steel pipe of same size as that of heat pipe – one each. 3.Equal capacity heater at bottom end of each pipe. 4.Water filled heat sinks at upper end of each pipe.Measurements and controls
a) Dimmerstat to control heat input to all the heaters – 4 amp. Capacity One No. b) A voltmeter and an ammeter to measure input to heaters One each. c) Multichannel digital temperature indictor to measure temperatures along the length of pipes.Four thermocouples are provided on each pipe. v Thermometers to note down water temperatures in heat sinks – 3 Nos.Services Required:
230 VA.C. Single Phase supply. Floor Area = 1 m X 0.5m X 0.5 m height.
