XTEMOS ELEMENT
AJAX PRODUCTS TABS
Baby Weighing Balance
A single beam scale, robust steel body with epoxy powder coated parts.
The beam carries a sliding weight to indicate the weight from 0 to 5kg in divisions of 20 grams each.
One hanger and one slotted mass is provided to increase the capacity of the balance.
When only the hanger is suspended from the end of the beam the capacity increases to 10 kg and the reading starts from 5 kg onwards on the scale up to 10 kg.
On adding the slotted mass on to the hanger the capacity increases to 15 kg and the reading starts from 10 kg onwards on the scale up to 15 kg.
The tray is detachable and can be easily replaced in position by sliding on to fixed plate.
Second scale is provided which reads 0 to 1 kg in division of 10 gms.
Making the total capacity of balance 16 kg in to 10 gms.
Diesel Fuel Pump Actual Cut Section
Diesel Fuel Pump Actual Cut Section
The working of diesel fuel pump is shown with the help of actual parts assembled on iron base. All the necessary parts of diesel fuel pump are shown in actual working form. This model helps the student to understand the working of the diesel fuel pump very easily. It is specially made dissectible for demonstration purposes.
A. Inline Type
B. Rotary Type
Lamp Unit, Triple
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Bell In Bell Jar
Pinned Joint Model
SPECIFICATION:
Model consists of hinged. Model will be able to demonstrate the qualitative behavior of the truss under load. As are very flexible, a compression members will easily it`s bucking i.e. It will curve of plain. The tension member however remains straight and tight. The student will therefore have a visual picture of the type of stresses i.e. Compressive or tensile that member of truss will carry under various positive of the load. In case of pinned joint truss, the student will be able to observe that angle between members at each joint undergo a small change.
Pulse Code Modulation/Demodulation
FEATURES:
• In-built sine wave generator • Test points to study different waveforms • In-built DC Power supplyTechnical Specifications:
• Sine wave Generator : Frequency : 1 KHz, Amplitude : 0 to 3Vpp • DC Voltage : -1.5 V to +1.5V • Clock Generator : Crystal based, 4.096MHz • Data rate : 64 kbps (for 8 KHz sampling rate)128kbps (for 16 KHz sampling rate) • ADC and DAC bits : 8 • Demodulator filter type : Butterworth low pass filter • Filter type : 6th • Filter cut-off frequency : 3.4 KHz • Mic Pre-amplifier : Transistor based • Compandingrange : -80dBm to +20dbm • Switched faults : 4 • Test points : 35 • Fuse : 30V, 100mV • DC Supply : ±5V, ±12V • System Bandwidth : 3.4 KHz
Germination Of Dicot And Monocot Seed
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Matt White Screen
Thermistor Unit
Photon Energy Array
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Mobile Insect Storage System
Description
An all new 'VERSATILE' space efficient, elegant looking, sturdy and compact system for insect storage supported with care, safety-privacy vis-a-vis being compact to accommodate large quantity in less space, easy to handle, convenient to monitor-sort. The system contains Compactor units which can be arranged to suite your requirements, according to the space available and above all can be secured with a single lock. The metallic compactor units made of mild steel with powder coated paint finish can be moved for handling the specimens and again joined to be locked only on the end unit and all units are secured. Showcases are arranged in rows of 20 each with two rows in each unit. End units are for 40 showcases whereas the intermediate units accommodate showcases back to back, i.e., 80 showcases and again the end unit for 40 showcases. Intermediate units can be increased as per space requirement. There are options for showcases, metallic or wooden. Size options of 53x45x7.5cm. or 45x45x7.5cm. or 45x30x6.5cm. with pinning EVA sheet is base, provision for insecticide, puller knobs, index card holder etc.
Two Stroke Diesel Engine Model
Westminister Electromagnetic Kit
Description
A very effective and motivating learning aid in elementary electromagnetism. Consists of 8 anisotropic alloy magnets, 8 ceramic ferrite magnets, 4 steel magnet yokes, 6 plotting compasses, 4 hardboard formers to take compasses, 1 bottle iron filings 250 gm, 4 dispensers for iron filings , 4 double C-cores, 4 clips for C cores, 4 Aluminium rings, 4 Aluminium split rings, 4 armatures with axle tubes, 4 Aluminium axle rods, 8 split pins, 16 rivets, 4 formers for coils, 4 reels cello tape, 4 reels copper wire, 4 sheets white pasteboard, 4 plain postcards, 4 reels white cotton thread, 1 length latex rubber tubing, 4 each resistors 100 ohms and 10 ohms, 4 support bases, 10 MES bulbs, 8 MES bulb holders,1 wood clamp and 1 wooden block. With instructions.
Buchner Funnel
Moulded in Polypropylene, our Buchner Funnel are highly sought after funnels in the market.
These two piece Buchner Funnel are light weight, easy to clean & autoclavable.
The top portion can be snap fitted with the lower one forming a vacuum seal which does not require greasing.
The base of top portion has a perforated filter plate.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Buchner Funnel 70 mm | 12 | |
| Buchner Funnel 110 mm | 6 | |
| Buchner Funnel 90 mm | 12 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Structure of bone model
Steering Geometry Wheel Alignment Trainer
Steering Geometry & Wheel Alignment Trainer
With the help of this trainer the students can learn about steering geometry and practically perform wheel alignment using various tools.
(A) Turn Tables
(B) Toe In Toe Out Gauge
(C) Magnatic Caster Camber Gauge
(D) Manual Steering System With Four Wheels
(E) Tool Kit
Survey Chain
Automatic Gear Box Actual Cut Section
Automatic Gear Box – Actual Cut Section
The working of automatic gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of automatic gear box are shown in actual working form. This model helps the student to understand the working of the automatic gear box very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
White Board Optics Set
Description
An economical and comprehensive set of equipment for ray optics and color experiments using magnetic-backed components that can be used on the whiteboard (included) or any installed steel (magnetic) board. Included a double ended light box contains a 12 V / 20 W halogen lamp, a wall-mount AC adapter, one end carries a cylindrical lens and slots for mounting the three slit diaphragms for ray optics. The other end carries two adjustable mirrors and an open area for color mixing work using colored filters that fit into slots in the ray box, Seven transparent color filters, seven opaque color filters, Three slits, one rectangular acrylic block, one semicircular block, one right angle 90° x 45° x 45°, One right angle 90° x 60° x 30°, one equilateral prism, four plastic coated ring magnets, one double convex block, One mirror strip, one double concave lens, two magic alphabet card and one mirror holder With instruction manual. The sizes of whiteboard supplied are approx. 580 x 390 mm.
CONDUCTIVITY METER
PRODUCT DESCRIPTION
All aqueous solutions conduct electricity to some degree. The measure of a solution's ability to conduct electricity is called "conductance" and is the reciprocal of resistivity (resistance). Adding electrolytes such as salts, acids or bases to pure water increases conductance (and decreases resistivity)
Conductivity Meter – Bench Top
Features:- Highly Stable & Accurate
- Cell Constant Adjustment Facility
- 3½ Digit Display
- Available in Laboratory & Field Models
- Automatic Temperature Compensation Facility
- Max Make, Table Pattern 6
- Pen Type (TDS/EC) Imported
- E.I Make, Model Alpha 06
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
