XTEMOS ELEMENT
AJAX PRODUCTS TABS
Human Tooth, Upper Triple Root In 6 Parts
Pinned Joint Model
SPECIFICATION:
Model consists of hinged. Model will be able to demonstrate the qualitative behavior of the truss under load. As are very flexible, a compression members will easily it`s bucking i.e. It will curve of plain. The tension member however remains straight and tight. The student will therefore have a visual picture of the type of stresses i.e. Compressive or tensile that member of truss will carry under various positive of the load. In case of pinned joint truss, the student will be able to observe that angle between members at each joint undergo a small change.
Phase Shift Keying Modulation and Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Phase Shift Keying Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supplies of ±12 V and ±5 V.
2. Built in Carrier wave Generator (Sine Wave) of 5 Vpp, 22 KHz ± 5% Frequency range with output on sockets.
3. Built in Data Generator using IC 7490 with four modulating signal outputs on sockets.
4. IC TL084 & IC 7486 are using for PSK demodulator.
5. Circuit diagram is printed on the milky white top panel and important connections are brought out on the sockets.
Electronic Ignition System Of An Automobile
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Variable Inductor
Description
The enamelled wire winding and a cylindrical soft iron core are built into this unit. The iron core displacement inside the winding can manually adjusted by the knob to give precise measurements up to 1.3 H. Connections are made through 4 mm sockets.Specifications:
Resistivity: 0.0165 W/m; Inductance: 0.15 to 1.3 H; Voltage: 30 V AC or 60 V DC.
Photo Gates & Leads
These pair of photo gates is housed in tough moulded cases giving them excellent durability.
The lamps operate on 6 Volts with a special built in circuitry which prevents lamps from damage in case higher voltage is applied accidently.
The photo gates can be connected by 4 mm. sockets to a timer and power supplies.
Analgesiometer Tail Flick
Analgesiometer Tail Flick (Radiant Heat or Tail Flick Type): It provides pain stimulus by heated nichrome wire in a Rat's tail to determine analgesic effect of drugs.
Complete with one spare element to work on 220 A.C.
Features
Shutter operated lamp illumination system. Automatic or manual mode for detecting tail flick. Precise and reproducible results. PC Connectivity with software. Software with calibration and report generation feature. Software with auto experiment number and serial number feature. Software with provision to convert data in excel or pdf. Cut off timer to avoid damage to animal. Calibration mode using Heat Flux meter (optional device).
Small Dental Care Model (28teeth), PVC
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Ringing Table
CNC Mill Trainer1
CONTROLLER:
Type of Controller System : PLC based system under collaboration from tudor,uk Main Spindle Drive : D.C. Thyristor Drive, Inbuilt Safety X, Y and Z axis Drives : Stepper motor drive TTL Compatible Input to Stepper :Optically lsolated , motor drive TTL Compatible Interpolation : Linear, Circular parabolic Interpolation Code Used : G, M, S, T, F, I, K, M, F, Cycles : Circular Interpolation, Mirror, Pocket Milling Cycle Pocket & Helical Milling : Provided with Std Codes Real time tool path :with online 3D simulationTABLE:
Length x Width : 600 x 225 (approx.) Clamping Area : 450 x 160 (approx.) T Slots : 10mm slot width.MACHINE DETAILS:
Resolution : 5 micron(Standard) Distance from sindle :25-225mm(Nose to table top) Centerline to column :170mm Rapid Travel 700 mm/min Weight in kg : 950kg Dimension in mm : 1200 x 1200 x 1900 mmSPINDLE:
Spindle Speed : Continuous Variable Spindle power : 1.5 HP Inside Taper : ISO 30 Speed Range : 300 to 3000 RPM
Sterling Engine Working Model
The Stirling engine was invented by Robert Stirling, a Scottish minister, in 1816. A Stirling engine is a heat engine that operates by cyclic compression and expansion of air or other gas, the working fluid, at different temperature levels such that there is a net conversion of heat energy to mechanical work.
Newton Meters
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Steam Engine Model
DC Servo Motor Controller
This trainer designed for versatile Applications / Experiments mentioned below. It consists of(i) a PWM Chopper Drive using MOSFET (ii) DC Servo Motor (iii) Speed Sensor (v) PI Loop for speed. This trainer system is a compact & advanced version for class room experiment setup for the students to operate and study a practical speed measurement using optical sensor and speed control system.
FEATURES:
• One 12V PMDC Motor mounted on a open frame. • Speed Range: 0 to 1500 RPM. • Speed Sensor fixed on the frame. - Photo interrupter with optical Encoders. • One F/V converter is provided to convert the pulses to voltage output. • Speed controller provided to select - Proportional circuit. - Proportional plus Integral circuit. • One 3½ digit display to display the speed of the DC Servo motor / set value. • A switch provided to select the reference or the actual speed. • All important signals are terminated at sockets. So that, the student can monitor / measure the signals using CRO, DVM, Frequency counter etc.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Plant Mitosis
Hydraulic Drum Brake Actual Working Two Drum
Pregnancy Pelvis With Baby
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Wireless Connectivity Kit
A Powerful Wireless Connectivity board is designed based on Sitara AM335X Cortex-A8 for detailed and combined study of different Wireless Communications. All in one Wireless Kit contains GSM/GPRS, GPS-GLONASS SBAS (GAGAN), ZIGBEE, RFID, Bluetooth and Wifi on board modules. It supports Linux, WinCE and Android OS Packages which can be used to study different applications like GPS tracking, wireless home and industrial security system, SMS and ZigBee based home application and lighting control and many more.
Features
• TI Sitara AM3354: - ARM Cortex-A8 32-Bit RISC Microprocessor NEON SIMD Co-processor - SGX530 Graphics Engine • DDR3 RAM : 4 GB • NAND Flash : 4 GB • 7” TFT Display Interface • Touch panel (Resistive and Capacitive) interface • On board WLAN (802.11 b/g/n), Bluetooth (802.15) • USB 2.0 – Host, OTG • Serial Interface : UART, SPI, I2C • On board - 10/100MPPS Ethernet PHY • Audio : - Digital Microphone - Multichannel Audio Serial Port (McASP) • Analog to Digital Converter
Arthropoda
| Daphnia WM | Cyclops Male WM |
| Cyclops Female with egg sac WM | Anopheles Male adult WM |
| Anopheles Female adult WM | Anopheles Mouth Parts Male WM |
| Anopheles Larva WM | Anopheles Egg WM |
| Cockroach Mouth Parts WM | Cockroach Malpighian Tubules WM |
| Cockroach Hepatic Caeca WM, TS | Cockroach Ovary TS |
| Cockroach Testis TS | Cockroach Leg WM |
| Cockroach Thoracic Spiracle WM | Cockroach Abdominal Spiracle WM |
| Cockroach Abdominal Spiracle WM | Cockroach Gizzard TS |
| Cockroach Trachea WM | Cockroach Striated Muscles WM, TS |
| Cockroach Wing WM | Cockroach Compound Eye VS |
| Culex Mouth Part Male WM | Culex Mouth Part Female WM |
| Culex Male WM | Culex Female WM |
| Honey Bee Mouth Parts | Honey Bee Leg with Pollen Basket WM |
| Honey Bee Sting Apparatus WM | House Fly Mouth Parts |
| Butter Fly Mouth Parts | Bed Bug WM |
| Bed Bug Mouth Parts WM | Prawn Gill TS |
| Prawn Gill WM | Prawn Statocyst TS |
| Prawn Hastate Plate WM | Prawn Compound Eye V.S. |
| Different Type of Insect Mouth parts WM | Different Type of Antenna WM |
Sonicator
Description
Ultrasonics (Ultrasound) is the sound which human beings cannot hear. Ultrasound utilizes frequencies from and above 18khz (18,000 cycles per sound) High frequency electrical energy is converted into ultrasound waves by means of ultrasonic Transducers, which are bonded on the base of S. Cleaning Tank. These high frequency sound waves create in the liquid countless, Microscopic vacuum Bubbles which rapidly expand and collapse.Features
Easy to operates & maintain with one piece S.S. Tank. Digital Tuning of Transducers with Generators to avoid any frequency shifted even during demanding applications. Compact, rugged and highly durable systems. Extensively protected electronic circuits means longer and safer Operations.Specifications
Operating frequency 33 -3KHz, for all general purpose cleaning is highly recommended Input Voltage range of 170V AC- 270V AC, 50 Hz, Single phase Micro Controller based timer range 0 to 30/99 minutes. Thermostatic controlled temperature controller. (Ultra Sonic Bath),Complete S.S & Digital Temp.Controlled Capacity 2 Ltr Approx Capacity 3 Ltr Approx Capacity 6 Ltr Approx
Multi Tank System
Panel Features
• Rocker switch is provided to ON/OFF the process plant. • Digital Panel Meter. • Pump Indicator. • Short Circuit protection. • Mimic diagram in the panel. • All the electrical connectors are terminated in the panel.Features
• This equipment consists of four tank system, conical tank system and spherical tank system. • Four numbers of Acrylic tank are provided for doing multivariable control of four tank system. • Conical tank (SS) is provided to performing the nonlinerar control system. • Spherical tank (SS) is provided for controlling the complex system. • Six numbers of level transmitter (DPT) are provided to measures the level of the each tank. • Three numbers of smart control valve with positioner are provided in the inlet of Flow rate. • Hand valve is provided at the bottom of the process tank to study the load disturbance. • Three numbers of hand valve are provided to control the Rotameter flow rate. • Three numbers of centrifugal pump are provided for water circulation. • Two flow transmitters are mounted for conducting flow, cascade and Ratio control. • Appropriate Digital panel meters are provided to measure the transmitter and actuator signals. • Delay coils are provided to the input of the process tanks for transportation lag study. • Storage tank of 100 litre capacity (SS). • Rotameter for Visual indication of the flow rate. • Relay circuit is provided to ON/OFF the solenoid valve. • Built in regulated power supply. • All Water flow lines are connected by (SS) fittings. • Necessary patch chords are provided for interfacing the Electrical signal. • Established successful design that mimics a real industrial process. • Front panel includes mimic diagram of the process, so students can clearly see what they are controlling. • Safe, practical and realistic. • Hand valves are provided to study the coupling (Interaction) and decoupling
Oscilloscope
This Oscilloscope is corresponding to horizontal with small size. The bandwidth of Y axis is DC 10 MHz and the deflection factor is 5 mV 5 V / div. It can be up to 50 V / div. using with the 10:1 probe. Sweep deflection factor is 0.1 ?s / div.
(1) Single Channel Single Trace Oscilloscope
(2) Bandwidth : 10 MHz
(3) Confirms to EN61010-1 (1993) and EN-IEC61326-1(1997).
(4) Wide measurement
(5) High sensitivity and trigger lock
(6) Sweep switch adopts digital code switch and accuracy
(7) Proper to use in colleges and for engineers and technicians
(8) Deflection factor is 5 mV – 5 V / div in 1-2-5 Sequence in 10 steps
(9) Accuracy: ±5 % (
10) Maximum Input Voltage: 400Vpk
(11) Sweep deflection factor is 0.1 us / div to 0.1 s / div
(12) Accuracy: ±5 %
(13) Trigger Sensitivity: INT:1.5 div EXT:0.3 V
(14) Trigger mode: INT, EXT, LINE, TV
(15) Trigger Sweep Mode: NORM, AUTO, TV. LOCK.
(16) Calibration Signal: 0.5 V Square wave of 1 kHz.
(17) CRT Effective working Area: 8 x 10 div. 1 div = 6 mm.
(18) Auxiliary Power Supply: 220V AC 50Hz
