XTEMOS ELEMENT
AJAX PRODUCTS TABS
6 Axis Robotic Trainer
For beginners this kit is very useful to learn the concept and working. For experienced, this kit helps to make new ideas. This kit is used to study the ROBO characteristics of arm movement. Each axis has one stepper motor. Gripper has one miniature cylinder to pick and place the object. Software controls the ROBO arm and measures the motor axis and arm axis. Simplicity of this kit makes maintenance easier and friendly to user. This kit is very flexible to operate and easy to move.
Features
• Easy to learn • New design • Easy for maintenance • Drive by stepper motor • Easy to programSpecification
• Arm : Jointed Arm • Axis : 6 • Motor : Stepper Motor • Gripper : Pneumatic • Drive : Stepper Motor Drive • Controller : MicrocontrollerBase
• Angle of movement : 320º • Gear Type : Spur Gear • Position Detector : Limit SwitchIntermediate ARM
• Angle of movement : 90º • Gear Type : Spur Gear, Worm Gear • Position Detector : Limit SwitchVertical ARM
• Angle of movement : 90º • Gear Type : Spur Gear • Position Detector : Limit Switch
Cortex M4 Development Board
Cortex M4 is an ideal replacement solution for the traditional Microcontroller & DSP Processors. Vi-S32 based on ST Microelectronics cortex M4 processor offers many features for Embedded Real Time world. The full range of hardware features on the board is provided to help you to evaluate and develop many applications. STM32 Embedded target enables systems and software Engineers to quickly deploy their application models in Matlab& Simulink to Cortex M4 ARM.
Specification
• STM32F407VGT6 microcontroller high performance 32bit ARM Cortex M4. • Operating upto 168MHz • 196Kbytes of SRAM • 2.4 MSPS Analog to Digital Converter • Two Nos. of Potentiometer interface for ADC input. • Two Nos. of DAC with simultaneous conversion • 1MB On-Chip Flash. • 4 Nos. of User LEDs, Relay Interface. • 8 way dipswitch for user input • I2C Based 2 digit 7 Segment display interface. • 4 keys keypad, Stepper Motor driver interface. • USB OTG FS with micro AB connector interface. • RTC with battery backup • I2C EEPROM device interface • SPI based temperature sensor interface • 1 Gbyte Micro SD Card interface • RS232 UART interface at a pin D connector/USB connector • CAN 2.0 lines are terminated at 9 pin D female connector • 3.2inch 240 x 320 TFT color LCD with Touch Screen • 10/100Mbps Ethernet interface • Extension header for I2C, SPI & CAN • Camera Interface
Distributed Control System
A powerful, modular & upgradable DCS has been designed and configured based on Siemens controller SIMATIC PCS7 ASRTX (Micro Box). Distributed I/O system ET200M can be provided for field automation. The distributed I/O can be connected via Profibus, Communication. DCS consists of controller, Power supply unit, distributed I/O, Digital Input and Output modules, Analog Input and Output module. a Demo Panel and Simatic PCS7 V9.0 Software.
DCS Controller
• Make : SIEMENS. • Controller : SIMATIC PCS 7 AS RTX BOX. • Profibus Communication done via CP5611 onboard. • Transmission Rate of Profibus cable is 12 Mbit/s. • 2 x GBIT & RJ45 LAN • Core 17-3517 Processor 1.7GHz, 4GB DDR3 RAM, SSD 80GB, 4xUSB V3.0 • Mouse and Keyboard • Windows7 • Win AC RTX 2010 software controllerDistributed I/O station ET200M
• Support HART, PROFIBUS, Foundation Field bus. • 16 No’s of digital Inputs with 24V DC. • 16 No’s of digital Outputs with 24V DC. • 8 channels of Analog Inputs with 4-20mA. • 8 channels of Analog Outputs with 4-20mA. • 24VDC /10A inbuilt power supply.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Surface Tension Balance, Searle’s
A horizontal frame is mounted on a rod fitted to a base & carries a steel wire stretched across it, the tension of which can be adjusted by a tightening screw.
A light metal pointer with a counterpoise is attached to the centre of the wire clamp.
A pan is hung from a notch in the pointer and has a hook at its underside from which can be suspended a light weight rectangular frame or a metal clip to hold a micro slide edge.
The tip of the pointer moves over a graduated scale. With rectangular wire frame, slide clip, six micro slides & 3 meters of spare wire.
Action of Cams
Carburetors Actual Cut Section
Bar & Gauge
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
SILICON RUBBER TUBING
PRODUCT DESCRIPTION:
The Rubber Company supply a wide range of high-quality silicone rubber tubing which is suitable for use in a range of applications. This highly versatile product is available in a variety of compounds and finishes to suit any application or environment. We also supply this particular tubing in a range of different colours and sizes to match your unique requirements.
Silicone rubber tubing is a highly durable as well as flexible product. This ensures that you get a product which can follow any curves or bends without showing signs of deterioration or warping. It also has a wide temperature range which enable you to use it in almost any environment with ease. In order to ensure you get the perfect product for your application we have included information about the 4 most popular silicone tubing products.
Material Kit Solids
Economy Kit of 14 materials blocks.
This economy kit consist fourteen materials in the form of rectangular blocks, intended to familiarize the student with the appearance, 'feel', texture, hardness and density of a range of common substances.
Blocks, 50 x 40 x 30 mm. Wood, paraffin wax, aluminium, Iron, foamed polystyrene.
Blocks, 20 x 20 x 100 mm. Perspex, glass, slate, aluminium, softwood, Marble.
Blocks other sizes: Lead 50 x 50 x 20 mm
Brass 20 x 20 x 50 mm
Iron 40 x 40 x 20 mm
Air Conditioning Trainer Window Type
Window air conditioner is becoming now a day’s necessity. The unit demonstrates the application of window air conditioner & evaluation of its performance. It consists of a small room to which a small air conditioner is connected the room is provided with a transparent front cover with a heater inside to simulate heat load in the room. Various measurements are provided so that performance of system that is COP of system, actual & theoretical cooling capacity of system & power consumption of unit with different load conditions.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirloskar make, having the capacity of 1/10 ton of refrigeration using R-12 refrigerant to keep room temperature between 20 to 30 c. 2.Condenser – Finned tube type, with forced air flow over the tubes, 3.Capillary tube of matched length as expansion device. 4.Evaporator – Finned tube type with forced air flow, 5.Room – 0.6 X 0.7 X 0.7 m. height, provided with transparent front wall. A heater with input control is provided inside the room. Which simulates different load conditions. 6.Measurements and Controls a) H.P. / L.P. Pressure gauges b) Digital temperature indicator to measure the temperatures at various points. c) Energy meters to measure input to compressor & heater. d) High and low pressure cutout. e) Thermostat to put off the compressor at set room temperature. f) Necessary switch for electrical components.SERVICES REQUIRED:
1.Floor area of 2m X 1 m. 2.230V, 15AC stabilized supply with earthing connectionXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Hand Stroboscope
Refrigeration And Air Conditioning Components
Actual Cut Section – Display Board (Set Of 30)
This actual cut section model is a set of thirty components used in refrigeration & air conditioning. With the help of this model students can understand the working parts of the components used in refrigeration & air conditioning. This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Human Circulatory System
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Single Shoe Brake Working Model
Small Dental Care Model (32 Teeth) PVC
Newton’s Color Disc
Description
To demonstrate the discovery made by Newton that white light is composed of seven colors. Consisting of a pulley mounted on a metal stand, the seven colored disc is driven by gears connected to a hand driven wheel. When the colored disc rotates, the eye can’t distinguish between individual colors and perceive it as white color.
Laboratory Spatula
Acquire from us high quality Laboratory Spatula at affordable price range.
Moulded in Polypropylene, Spatula consists of a spoon on one side while the other end is a flat construction with a knife edge.
This is helpful in breaking up crystals of different salts while the spoon is used to draw salts from the containers.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Spatula 150 mm | 12 | |
| Spatula 200 mm | 12 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Clinometer Compass
Description
Clinometer Handle Compass is a reproduction of an antique Clinometer compass. The Handle Compass gets its name from its "handle" shaped sight, which actually serves two purposes With the compass level, an object can be viewed through the peep sights to determine its magnetic heading. The second and most interesting purpose is when tilting the compass on its side and viewing an object through the sights, its angle of elevation or declination can be found. A weighted pendulous arm beneath the compass needle can be read from one of three scales : Angle in degrees beneath the zenith (from straight up), angle in degrees of elevation or declination, and in inches per yard of slope. The compass has a needle lift mechanism to protect the compass jewel and the pendulous arm when being transported.
Smart LED Lighting module
Zigbee offers Green and Global Advanced Wireless Technology, Connecting the widest range of Devices to work together intelligently and help you to control your real world. CC2530 is the first System On chip, which has integrated 8051Microcontroller with ZigBee RF transceiver. A WSN based Smart LED lighting module has been developed with latest LED controller from MICREL, 10 LEDs, ZigBee RF module using CC2531 for Wireless Control with onboard Light Sensor. WSN based LED lighting module has a Base Board and a Zigbee RF module. Zigbee RF module can be plugged into the connector provided on the Base Board, meant for further upgradation.
Features
• 10 Nos. of LED of 2watt each • 400 milliwatts LED • Constant current driver for LED control • Connectors for plug-in Zigbee RF module • Remote ON/OFF control by Zigbee RF Control • On board light intensity sensor • LED Brightness control either by program or by Light Sensor input.
