XTEMOS ELEMENT
AJAX PRODUCTS TABS
4 Stroke 6 Cylinder Diesel Engine
4 Stroke 6 Cylinder Diesel Engine – Motor Driven Actual Cut Section Working Mode
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine willbe supplied with key card & very interesting literature regarding working.
10KW IGBT Based Power Module
FEATURES:
• 1200V/ 75A, Peak Semikron based IGBT module • 8 Nos of IGBT’s provided with independent eight driver (inbuilt opto isolator) • All the collector and emitter terminals are brought out of proper connectors for power circuit connection • All the gate and emitter terminals are brought out and terminated on front panel to view driver output fault output • Indicator LED provided for PWM input and power supply input • Proper heat sink provided for all the IGBTs with cooling fan provision • All are enclosed by viewable acrylic cabinet • Temperature sensor provided for over temperature Protection • PWM inputs are brought out on Front Panel, you may connect any controller for interface • One common +15V Power supply for all the driver circuit, Inbuilt isolated power supply provided. • Over current protection and short circuit protection provided for all individual IGBT module • Reset circuit provided and terminated to clear the fault • Snubber capacitor provided for dv/dt protection for all IGBT module • 60A 3 phase bridge rectifier and filter circuit available for power circuit input.
Friction In Pile Lines Apparatus
DESCRIPTION:-
The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the losses due to fiction in pipes Ø To determine the friction factor for Darcy Weis back equationUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pipes (2 Nos.) : Material GI of ½ “ & 1” Diameter Ø Pipe Test Section : Length 1 m Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 25 Ltrs. Ø Sump Tank : Stainless Steel, Capacity 50 Ltrs. Ø Stop Watch : Mechanical / Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted StructureXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Wide Range Adjustable Micrometer
Description
Micrometer is used to measure short lengths accurately Technical Details : Printed Marking on the Vernier Scale Carbide Tipped Measuring Faces Blue Metallic Finsh Frame Plate Frame With Locking Clamp and ratchet stop Least Count: 0.01/0.001” Wide Range Measurement Interchangeable Anvils Type Sizes 300-400mm 400-500mm 500-600mm 600-700mm 700-800mm 800-900mm 900-1000mm 1000-1200mm 1200-1400mm 1400-1600mm Specifications: Guarantee ; 6 Months without abuse Packing ; Wooden Box Calibration ; In house.
Venturimeter Orificemeter Calibration Set Up
DESCRIPTION:-
The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different floe rate. Flow rate of water is measured with the help of measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the Co-efficient of discharged through Venturimeter and Orificemeter Ø To measure discharge through Venturimeter and Orificemeter as flow meters.UTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATIONS: –
Ø Venturimeter : Material Clear Acrylic, Compatible to 1” Dia pipe Ø Orificemeter : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Pins
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Direction of Current
Bar Breaking Apparatus
Description
A heavy cast iron stand slotted to carry a stout iron bar, with ten cast iron breaking bars. Comprising a heavy cast iron frame 340 x 120 x 100 mm with slotted end pillars to carry a stout iron bar. The bar is threaded at one end for a large tensioning nut and has holes at the other end to accommodate the cast iron breaking bars. Supplied complete with ten breaking bars.
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
Bell In Bell Jar
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Lathe Tool Dynamometers
This is a strain gauge type two component lathe tool dynamometer designed to measure vertical and horizontal forces on the while orthogonal cutting process. The unit is in two parts one is mechanical sensing unit or tool holder, which can mounted on the top of the Ross slide after removing swivel base and compound slide of a lathe and digital force indicator. With this Dynamometer student can study the change in these forces by varying Speed, Cut and Feed.
FEATURES:
1.Rigid in construction 2.Sensitive transuding and amplifying system for accuracy in force measurement. 3.Compact Digital force indicator. 4.Use of cutting fluid during operation is possible.SCOPE OF SUPPLY:
1.Mechanical sensing unit or Tool Holder with string gauges. With H.S.S. tool of ½ “ size. 2.Control panel housing digital force indicator to measure two forces simuletensiously, balancing potentiometers, connoting cable. 3.Necessary switches, fuses and polycarbonate front plate. Range o to 500 Kg. 4.Centre Height, P.C.D.of clamping bolt size, clamping Bolt size. Three component lathe tool dynometer is also available.
Rocking Microtome
Description
A sectioning equipment, economical and simple, yet providing all facilities of a standard rotary microtome. The internal mechanism is fully enclosed in a sturdy metal case, for protection against dust and grit & is driven by a handle which can be locked in position. A ball & socket type movement permits use of the entire knife edge. With a feed range of 1 to 25 microns in steps of 1 micron. Supplied complete with a set of three object holders, one razor 120 mm with back and handle, one honing plate, one bottle of oil for lubrication, dust cover and wooden cabinet.
Multiple Input/Output Process Trainer
Panel Features
• Power ON/OFF switch • Heater selection switch • Heater and pump indicators • High current fuse carrier for • Heater protection • Provision to run the stirrer • Digital panel meters • Two numbers of industrial PID Controller • Electrical test points are provided to measure the current signal • Mimic DiagramFeatures
• Two numbers of flow Transmitter (DPT) are provided to sense the flow of the liquid. • Three numbers of temperature transmitter (RTD) are provided at various stages to measure the temperature. • Five numbers of level sensor (RF capacitance) are provided to sense the level of each tank. • Industrial type Conductivity sensor is provided to analyze the conductivity of given Solution. • RTD sensor (or) Thermocouple acts as a temperature sensor. • Digital panel meters are provided to indicate the output of each sensor. • Provision to measure the conductivity. • Two numbers of motorized control valve or pneumatic control valve are provided to control the flow of the pipe line. • A powerful thyristor based power driver is provided to drive the heater power. • An industrial type water heater is used as a heat Source. • Storage tank of 50 litre capacity (SS). • Process tank of 15 litre capacity (SS). • Four numbers of acrylic tank are provided to study the response of four tank systems. • In necessary location Ball valve, globe valve and needle valves are provided. • Two numbers of stirrer are provided in the temperature process and alkaline process. • Three numbers of centrifugal pump (FHP) is used to circulate the water from storage tank. • Six numbers of rotameter are provided in the process inlet to visualize the real flow. • Regulated power supply is mounted in the panel. • All the flow lines are fitted by (SS) pipe fitting. • An over head tank is provided to give constant flow. • All the equipments are mounted in a rugged and mobile type metallic work station.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Front Axel Assembly With Differential Gear
Front Axel Assembly With Differential Gear (Actual Cut Section)
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Laser Distance meter Lite
Description
Base Model for all basic measurements. It is small, robust base model for modern measurements. Reliable, accurate, precise and easy-to-use. We are among the prestigious industry players, engaged in offering Laser Distance Meter to our valuable customers. The offered meters are designed in strict compliance with the industry standards and are highly appreciated by the customers. These meters are accurate and are regarded for their compact size and.
Laser Distancing Meter
Description
Laser Distancing Meter The professional Laser Distance Meter is designed to give special users a high accuracy, one person distance measuring and estimating tool measure remote and difficult reaching places. The compact and handy base model was specifically designed for indoor applications. Shortcut keys for addition, subtraction, Pythagoras, area and volume calculation make measuring fast and very reliable. The last 20 measurements are also stored. Simple to Operate: Due to the shortcut keys addition and subtraction, as well as surface and volume calculations could be easier. Features : Area, Volume Calculations Indirect measurement using Pythagoras Addition/ Subtraction Continuous Measurement Min/ Max. Distance Tracking Display illumination and multi-line display Buzzer indication Multifunctional end pieces.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Tablet Coating Pan
Product Description
We offer coating pan that is designed to perfection and fabricated from best grades of raw material procured from reliable sources. These coating pan are suitable for coating tablets and is checked by our quality controllers for high performance and uniform coating all over the tablet. The different parts of our coating pan machines are listed as under:PAN
The coating pan is SS semi ellipsoidal size pan with a circular mouth for charging & discharging of tablets, Pan mounted at an inclination of 45 degrees to the horizontal.DRIVE ASSEMBLYPAN
The tablet coating pan consists of a suitable HP 3 Phase, 440 V, 1440 RPM TEFC motor with suitable worm reduction gear box and cone pulley arrangement to give three speed output.HOT AIR BLOWERPAN
The tablet coating pan unit is provided with a hot air blower consisting of suitable HP 3 Phase 440 V, 2880 RPM TEFC electric motor & centrifugal blower with damper delivering required CFM. The air is heated by means of suitable electric heater to give air at 30 to 90 degrees Heater with thermostat control and flexible hose pipe.
Open Wind Tunnel Apparatus
Technical Description
A wind tunnel is the classic experiment system for aerodynamic flow experiments. The model being studied remains at rest while the flow medium is set in motion, and thus the desired flow around the model is generated. Open wind tunnel used to demonstrate and measure the aerodynamic properties of various models. For this purpose, air is drawn in from the environment and accelerated. The air flows around a model, such as an aerofoil, in a measuring section. The air is then decelerated in a diffuser and pumped back into the open by a fan. The carefully designed nozzle contour and a flow straightener ensure a uniform velocity distribution with little turbulence in the closed measuring section. The flow cross section of the measuring section is square. The built-in axial fan with guide vane and a variable-speed drive is characterised by an energy-efficient operation at high efficiency. Air velocities of up to 28m/s can be reached in this open wind tunnel. The trainer is equipped with an electronic two-component force sensor.Lift and drag are detected and displayed digitally. The air velocity in the measuring section is displayed on the inclined tube manometer. The tube manometers is recommended for measuring the pressure curves in drag bodies. Extensive accessories allow a variety of experiments, for example lift measurements, pressure distributions, boundary layer analysis or visualisation of streamlines. The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.Learning Objectives & Experiments
– Determine drag and lift coefficients for different models – Pressure distribution when flowing around drag bodies – Boundary layer analysis – Investigation of flutter – Wake measurementFeatures
* Open wind tunnel for a variety of aerodynamic experiments * Homogeneous flow through the flow straightener and special nozzle contour * Transparent measuring section
TMS320F2812 Based DSP Trainer
FEATURES:
• 12 Motor control PWM & 4 Individual PWM output • 16 channel, 12 bit ADC • 56 Individually programmable GPIO lines • 2 Quadrature encoder interface / 6 capture input • 128K x 16 bit flash memory • 1K x 16 bit OTP ROM • 14K x 16 bit SARAM • 16 LEDs are provided for user program development & debug • Opto isolated USB to Serial Interface • 3 Switches are provided for user interface like, frequency, speed variations etc., • Bead Inductances provided for RF EMI rejection • 16 ADC inputs are protected and terminated at 26 Pin FRC connector. • 8 I/O lines are protected and terminated at 50 Pin FRC connector • 12 PWM outputs and 6 capture inputs are terminated at 34 pin FRC connector • On board isolated USB to JTAG interface
Rotary Shaker (Platform Type)
Body made out of thick mild steel finished with powder coating.
Heavy duty PMDC motors for suitable capacities are provided for long time, continuous operation.
Fixed speed and variable speed models are offered.
Platform is provided RPM range-upto 250 RPM, electronic control, 0-60 min timer.
Workable on 220 V AC 50Hz single phase.
Optional
Digital R.P.M. indicator. Digital timer (0-99 min.).| Platform size in cm | Holding capacity | |
|---|---|---|
| 45x45 mm | 25 flasks of 100 ml | |
| 45x45 mm | 36 flasks of 50 ml | |
| 45x45 mm | 16 flasks of 250 ml | |
| 55x55 mm | 25 flasks of 50 ml | |
| 65x65 mm | 36 flasks of 250 ml | |
| 105x105 mm | 81 flasks of 50 ml | |
| 105x105 mm | 64 flasks of 250 ml |
