XTEMOS ELEMENT
AJAX PRODUCTS TABS
Bending Moment & Shear Force Apparatus
INTRODUCTION:
Shear Forces occurs when two parallel forces act out of alignment with each other. For example, in a large boiler made from sections of sheet metal plate riveted together, there is an equal and opposite force exerted on the rivets, owing to the expansion and contraction of the plates. Bending Moments are rotational forces within the beam that cause bending. At any point within a beam, the Bending Moment is the sum of: each external force multiplied by the distance that is perpendicular to the direction of the force.EXPERIMENT MANUAL:
1. To verify the Shear force a cross-section of the beam. 2. To verify the bending moment in cross–section of beam with a flexure condition.APPARTUS SPECIFICATION:
1. Dimensions : 158 cm X 45cm X (h)60cm 2. Total Beam Length : 160 cm with flexure 3. Width of Beam : 5 cm 4. Distance of Length in between : 5 cm 5. Height of beam : 36 mm 6. No. of Hanger for weights : 3 7. No. of Spring Balance : 2 (of 10kg) 8. Total Weight of Apparatus : 13.1 kgACCESSORY REQUIRES:
1. Shear force apparatus 2. Bending Moment Apparatus 3. Hangers 4. Weights 5. Two Spring balances – 10kgs
Human Torso, With Head, Half Size
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Compound Microscope (Student Microscope)
Specification
Elegant body, practical design and coated lenses. Fixed square stage 120mm x 120 mm with optional mechanical stage or slide clips. Focusing by coarse & fine adjustment knobs. Illumination by plano concave mirror reflector or optional LED light. Eye Piece 10x & 15x Objective 4x, 10x , 40x/45x 100x oil immersion is optional. Available in Styrofoam pack for safe & easy transport. Wooden Box is optional.
AED Trainer
Description
The Laerdal AED Trainer 2 offers an affordable alternative for educating the layperson and healthcare provider in the effective use of an automated external defibrillator.Product benefits:
Educationally effective, offers all the essential features necessary for learning appropriate AED use and techniques. Affordable training through the simulation of the HeartStart FR2 AED in appearance and operation. Added instructor flexibility through unique control of the scenario selection by use of the remote control device. Flexible configuration of the device through a scenario builder program that allows the additional creation of custom training scenarios. Cost-effective operation through use of six C-cell batteries.Product features:
Ten pre-configured sudden cardiac arrest scenarios compatible with training programs developed by internationally recognized responder programs. Remote control (optional) for manual scenario selection pause/resume function, AED Trainer 2 volume control, motion artefact, low battery or replace battery, loose electrodes connection, shock able or non-shock able rhythms and error conditions that simulate the red X in the Heart Start FR2’s status display window. Designed for use with the AED Little Anne® and AED Resusci Anne® manikins with Laerdal LINK Technology by providing student feedback as to proper pad placement on the manikins. It can also be used with any other manikin where Laerdal Link Technology is not available. Proper pad placement required in order for the trainer to advance in the scenarios when used with the AED Little Anne or AED Resusci Anne manikins.
Automobile Parts Actual Cut Section
This model helps the student to understand the working of automobile parts very easily. It is specially made dissectible for demonstration purposes.
1 Self Starter
2 Battery
3 Distributor
4 Ignition Coil
5 Spark Plug
6 Magneto
7 Electrical Fuel Pump
8 Mechanical Fuel Pump
9 Master Cylinder
10 Brake Cylinder
11 Gear Lubricating Pump
12 Water Pump or Water Body
13 Radiator
14 Crank Shaft
15 Cam Shaft
16 Connecting Rod
17 Piston With Rings
18 I.C. Injector
19 Speedometer
20 Shock Absorber
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Orbital Shaking Incubator
Specification
Outer made of M.S. Sheet powder coated & inner chamber is made of thick S.S. Sheet. The gap between two walls is fitted with high grade glass wool. The glass window makes it possible to inspect specimen without disturbing inner Temperature. The unit has a temprature range from ambient to 60°. Temperature is controlled by Dual Display Microprocessor PID Digital Temperature Indicator Cum Controller with a accuracy of + 0.5°C. Air Circulation Fan is provided to maintain stability throughout. Speed of shaker is variable from 30 RPM to 250 RPM. The tray of the shaker is also made of S.S. Sheet with Lotus type clamps to hold flasks. Unit is fitted with Digital RPM Meter, 999 min digital time.Optional Accessories
Timer 0-24 Hours. 16 Flasks of 100ml. instead of 9 flasks of 250ml. 9 Flasks of 500ml or 25 flasks of 100ml instead of 16 flasks of 250ml. 25 Flasks of 250ml or 36 flasks of 100ml instead of 16 flasks of 500ml.Size
9 Flasks of 250ml. 16 Flasks of 250ml. 16 Flasks of 500ml.
MCT Box
MCT Boxes are moulded in polycarbonate and are therefore strong as well as autoclavable.
One size can hold 64 MCTs of 1.5 ml. & the other can hold 100 MXT's of 0.5 ml.
These MCT Boxes are designed to work at temperatures ranging from -190'C to + 121" C.
The transparent cover provides a good view of the contents inside & is numbered for better inventory control.
| Particulars | Pack (Pcs) | |
|---|---|---|
| MCT Box (Rack for 100 MCTs of 0.5 ml) | 4 | |
| MCT Box (Rack for 64 MCTs of 1.5 ml) | 4 |
Human Tooth, Upper Triple Root In 2 Parts
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Plantation Pots
Plantation Pots, moulded in polypropylene, are available in four different sizes.
The Plantation Pots have a downward extended rim, which provide convenient lifting even if the pot is filled.
The bottom of the pot is provided with holes for drain purpose.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Plantation Pots 100 mm | 20 | |
| Plantation Pots 150 mm | 20 | |
| Plantation Pots 200 mm | 20 | |
| Plantation Pots 250 mm | 20 |
Ruhmkorff Coil
Description
Ruhmkorff Coil produces pulses of high voltage spark from low voltage DC source (6 – 12 V DC). It is suitable for use with gas-filled discharge tubes, vacuum tubes, eudiometers and for general laboratory work. Includes an adjustable vibrator system, primary current polarity reversal, on-off switch, a capacitor enclosed in the box and special alloy contacts. Spark gap at the discharge points can be adjusted by sliding rods back and forth. Spark Length 15 mm.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Measuring Cylinder (Hexagonal Base)
We bring forth high quality Measuring Cylinder (Hexagonal Base) for our esteemed clients.
The hexagonal base provides excellent stability to the cylinder where as the tapered spout works really well while pouring any reagent.
These Measuring Cylinder (Hexagonal Base) are high on demand for their quality.
We source them from reliable manufacturers.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Measuring Cylinder 10 ml (Hexagonal) | 24 | |
| Measuring Cylinder 25 ml (Hexagonal) | 12 | |
| Measuring Cylinder 50 ml (Hexagonal) | 12 | |
| Measuring Cylinder 100 ml (Hexagonal) | 12 | |
| Measuring Cylinder 250 ml (Hexagonal) | 6 | |
| Measuring Cylinder 500 ml (Hexagonal) | 4 | |
| Measuring Cylinder 1000 ml (Hexagonal) | 3 |
Three Hinged Arch Apparatus
The mild steel model has a span of 100cm and rise 25cm, with hinges at supports and crown. One of the ends should rests on rollers. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically determinate structure, the horizontal thrust developed under the action of any load system can be theoretically calculated and will also be measured directly by neutralizing the outward movement of the roller end. A dial gauge with 25mm travel (with magnetic base) may be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Single Nose Microscope
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Linear IC Trainer
This Trainer Consist of :
1. Regulated power supply of ± 12 V / 250 mA.
2. Variable 0 to ±5 V / 250 mA.
3. Sine wave oscillation of 1 KHz.
4. Digital Voltmeter of 0-20 V DC, LCD display, 3 ½ Digit.
5. Functional diagram of IC 741 is printed with 2 mm sockets.
6. One extra 8 pin IC Base with 2 mm sockets.
7. Potentiometer of 10K Ohms.
8. Required Resistance and Capacitances mounted on board.
9. Interconnection Leads and Manual to perform 15 experiments on IC741 e.g. inverting, non-inverting, summing, difference, multiplier, differentiator, integrator etc.
Oscilloscope
This Oscilloscope is corresponding to horizontal with small size. The bandwidth of Y axis is DC 10 MHz and the deflection factor is 5 mV 5 V / div. It can be up to 50 V / div. using with the 10:1 probe. Sweep deflection factor is 0.1 ?s / div.
(1) Single Channel Single Trace Oscilloscope
(2) Bandwidth : 10 MHz
(3) Confirms to EN61010-1 (1993) and EN-IEC61326-1(1997).
(4) Wide measurement
(5) High sensitivity and trigger lock
(6) Sweep switch adopts digital code switch and accuracy
(7) Proper to use in colleges and for engineers and technicians
(8) Deflection factor is 5 mV – 5 V / div in 1-2-5 Sequence in 10 steps
(9) Accuracy: ±5 % (
10) Maximum Input Voltage: 400Vpk
(11) Sweep deflection factor is 0.1 us / div to 0.1 s / div
(12) Accuracy: ±5 %
(13) Trigger Sensitivity: INT:1.5 div EXT:0.3 V
(14) Trigger mode: INT, EXT, LINE, TV
(15) Trigger Sweep Mode: NORM, AUTO, TV. LOCK.
(16) Calibration Signal: 0.5 V Square wave of 1 kHz.
(17) CRT Effective working Area: 8 x 10 div. 1 div = 6 mm.
(18) Auxiliary Power Supply: 220V AC 50Hz
Hypsometer, Regnault’s
Description
Double walled copper cylinder, 340 x 60 mm, mounted on steam boiler, with thermometer tubule at top and side outlets for manometer and draining. Double walled copper cylinder 34 x 6 cm mounted on steam boiler. Fitted with thermometer, draining tube and glass manometer with rubber bungs. For the determination of the upper fixed points of thermometers andboiling points at barometric pressures other than atmospheric. Double walled copper cylinder 34 x 6 cm height x outer dia. mounted on steam boiler. Fitted with thermometer tubulure at the top, side outlet draining tube and glass manometer mounted in tubulure with rubber bungs.
Reciprocating Compressor Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Friction In Pile Lines Apparatus
DESCRIPTION:-
The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the losses due to fiction in pipes Ø To determine the friction factor for Darcy Weis back equationUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pipes (2 Nos.) : Material GI of ½ “ & 1” Diameter Ø Pipe Test Section : Length 1 m Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 25 Ltrs. Ø Sump Tank : Stainless Steel, Capacity 50 Ltrs. Ø Stop Watch : Mechanical / Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted Structure
