XTEMOS ELEMENT
AJAX PRODUCTS TABS
Ultrasonic Transmitter And Receiver Set
This apparatus consists of a self-contained transmitter and receiver operating in the 40 kHz region. The transmitted wave is modulated at a user controlled variable frequency of about 2 kHz and this is detected by the receiver which amplifies the signal and drives a miniature integral loudspeaker. Both transmitter and receiver are contained in separate plastic enclosures measuring 175 x 100 x 40 mm which contain all the electronics and the 9 V batteries. The receiver has front panel 4mm sockets so that the output can be monitored on an oscilloscope for more quantitative measurements. The system is ideal for demonstrating sound waves above the hearing threshold and reflection properties associated with sonar etc. A special feature is the second transducer on the transmitter which can be switched on when required to produce two coherent sources. By moving the receiver along a line parallel to the two sources interference patterns can be dramatically demonstrated simplifying the Young’s slits experiment or enabling it to be demonstrated using waves other than light. Complete with batteries, full instructions and suggestions for use.
pH Meter, Digital, Portable
Highly stable and accurate.
Digital display.
Technical Specification
Display: 3½ digit LCD Range: pH : 0 to 14.00 Resolution: pH : 0.01 Accuracy: pH : ±0.01 Compensation: Manual 0 to 100° Slope Correction: 80 to 120% Power: 1 x 9V Battery Dimensions: 85 x 28 x 165 mmAccessories
Combination pH Electrode Operation Manual
Pulley With Universal Clamp
Storage Vial (O Ring)
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Continuously Variable Transmission
Continuously Variable Transmission – Actual Cut Section
The working of CVT is shown with the help of actual parts assembled on square iron pipe frame. The CVT is driven through permanent magnet D.C. motor with variable speed control drive. RPM Sensor With Digital Display Is Also Provided. All the necessary parts of CVT are shown in actual working form. This model helps the student to understand the working of the CVT very easily. It is specially made dissectible for demonstration purposes.
Mock Layout Of Car Wiring Latest Type
Mock Layout Of Car Wiring Latest Type
All the components used in the apparatus are of modern car. The complete mock layout is beautifully divided into 5 sections as under
(A) Front Lighting Panel
(B) Dash Board Panel
(C) Ignition System
(D) Rear Lighting Panel
(E) Motorised Charging System
With the help of this mock layout system its becomes very easy for the students to understand the actual working of electrical system of a modern car.
Three Phase Cyclo Converter
This module is designed for three phase half wave-step down cycloconverter. It consists of 18 Synchronized firing pulses, 18 SCRs, Relevant power supply and circuitry for frequency divisions.
Specification
• Eightin nos. SCR with RC snubber protection is provided for 3phase • cycloconverter power circuit (each phase consist of 6 SCRs) Rated at 1200V@25Amps. • Three nos. center tapped inductor (0%.50%, 100%) is provided for power circuit. • Eightin nos. Isolated gate pulses for SCR power circuit. • One potentiometer is provided to vary the frequency. • One potentiometer is provided to vary the output voltage. • MCB protection. • Housed in sleek screen printer cabinet. • Provision for V/F control Power Supply. • Input 440V ± 10%, 50HZ three phase AC supply. • ± 15V DC, 9V, 9V, 9V AC (3phase) for the firing circuits. • 24-0-24V 3phase input for power circuit.
Turbine/Pump Unit
Description
For use as a water turbine to drive a generator producing electricity or for use as a pump driven by a motor and raising a head of water to produce potential energy. The rotor has eight 'bucket' blades and is housed in a block turbine chamber with a clear Perspex front. Two inlet tubules (for turbine and pump operation respectively) and one outlet tubule are provided and the shaft carries a 15 mm. diameter pulley. With driving belt.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Cam Analysis Apparatus
The apparatus is designed to study the cam profiles and performance of cam and follower system. The apparatus consists of a shaft supported by ball bearings upon which three different types of cams can be mounted.
The push rod for follower is supported vertically, which can adopt three different types of followers. Cams and followers can be changed easily. A variable speed motor rotates the cam. A dial gauge permits plotting of follower displacement with respect to cam position. By operating the system at different Speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. Jump can be visualized also with the help of stroboscope (it is not supplied With the product).
SPECIFICATIONS OF CAM ANALYSIS APPARATUS:
1.Cam -Eccentric, tangent and circular ARC type – one each. 2.Follower- mushroom, flat faced and roller type – one each. 3.Cams and followers are hardened to reduce wear of the surfaces. 4.Variable speed motor coupled to camshaft of suitable range and Variac. 5.A dial gauge to note the follower displacement. 6.A technical manual accompanies the equipment.SERVICES REQUIRE FOR CAM ANALYSIS APPARATUS:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Bench area 0.5m x 0.5m x 0.5m height. 3.Tachometer to measure the jumping speed, (can be supplied extra)
COPLIN JAR FOR 5 SLIDES
PRODUCT DESCRIPTION:
This popular staining jar has heavy glass walls and a broad base for increased stability. It holds five single 3" x 1" (75 mm x 25 mm) slides vertically, or 10 slides back to back, and requires low reagent volume (approximately 65 mL). Manufactured from soda-lime glass. Approximate inside dimensions: 26 mm L x 26 mm W x 90 mm D.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Light Box and Optical Set
Description
A Robust light box in matt black finish with a 12 V 24 W axial filament lamp with flexible leads. One end of the box takes a cylindrical convex lens in an adjustable sliding mount to enable production of convergent, parallel or divergent beams. Complete with accessories which consist of: 5 Plastic blocks, one rectangular, One semicircular, One equilateral prism 60° x 60° x 60°, One right angle prism 90° x 60° x 30° and one right angle prism 90° x 45° x 45°. 3 Cylindrical acrylic lenses: one double convex, one double concave, both having the same radius of curvature and one thick convex lens. 3 Mirrors, one plane glass, one curved parabolic and one curved semi-circular. 2 Slit plates, one with three narrow and one narrow slits, the other with four narrow and one wide slits 1 Set of eight colour filters, Red, Green, Blue, Cyan, Violet, Yellow, Orange and Magenta. 1 Set of coloured cards, Red, Green, Blue, Violet, Orange, Cyan, Yellow and Pink. Complete with one spare lamp, in box.
Continuously Variable Transmission
Continuously Variable Transmission – Actual Cut Section
The working of CVT is shown with the help of actual parts assembled on square iron pipe frame. The CVT is driven through permanent magnet D.C. motor with variable speed control drive. RPM Sensor With Digital Display Is Also Provided. All the necessary parts of CVT are shown in actual working form. This model helps the student to understand the working of the CVT very easily. It is specially made dissectible for demonstration purposes.
Block, Glass
Pin Fin Appatatus
The apparatus consists of a channel in which the pin fin is tested in both natural as well as forced convection. The channel is connected to the suction of blower. The blower is operated to touch the pin fin in forced convection only. In natural convection, the window above the pin fin is kept open to the atmosphere. Five thermocouple tapings are given along the length of the fin. Thus the temperature distribution along the length can be distinguished. Also natural and forced heat transfer co-efficient, effectiveness, etc. can be found out.
Specifications:
1.Three pin fins- a) M. S. b) Brass c) Al 2.Channel- 150mm x 100mm x 1000mm 3.Blower – run by f.h.p. motor. 4.Orifice meter along with water manometer to measure airflow. 5.Voltmeter and ammeter to measure power input. 6.Cr- Al thermocouple with 6 tapings along with temperature indicator. 7.Dimmerstat to control power input. 8.A band heater to heat the pin fin. A technical manual accompanies the unit.Services required:
1.220v, stabilized single phase supply along with earthing Connection. 2.Floor area 2m x 1m x 1m height.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Sets of metal discs
Description
For demonstrating that some metals are magnetic whilst others are not and for general Metal Identification’ exercises. Comprises sixteen discs, 25 mm. diameter 2 each of Mild Steel, Stainless Steel, Brass, Zinc, Nickel, Silver, Bronze, Aluminium and copper. One of each is stamped with the name of metal. the other is unmarked.
Motor Generator Model Set
Description
This motor-generator set gives students an insight into the physical and technical relationships on which electric motors, generators and transformers are based. The modular system allows to set up different function models without tools: Various DC motors Series and shunt motor Synchronous motor DC generator and alternator Transformer. This set allows the performance of 10 student experiments about the following topics: Magnetic field of a coil Conversion of electrical energy into kinetic energy Commutator Direct current motor Synchronous motor Series and shunt-wound motors Electromagnetic induction The electrical generator Engine-generator Transformer
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Centrifugal Pump Test Rig
Centrifugal Pump Test Rig
Closed Circuit Type With S.S. Tanks, ISI Mark Pumps & Motors, Powder coated The closed circuit test rig consists of a “kirloskar make” monoblock centrifugal pump. The pump is provided with a vacuum gauge on suction pipe and a pressure gauge on discharge pipe. The gate valve is used to adjust the head on the pump. The discharge is measured by measuring tank / water flow meter. The input power is measured by energy meter.
Specifications:
l. Centrifugal monoblock- 1 h.p. 2. Pressure gauge and vacuum gauge for measuring the head. 3. Measuring tank of 400×400 x400 mm OR Water flow energy meter for measuring the discharge. 4. Stop watch. 5. Sump tank of sufficient capacity. 6. Energymeter to measure input power. 7. A technical manual accompanies the equipment.Features:
1. The equipment is coated with an attractive and anticorrosive powder coating. 2. The equipment consists of ISI standard (i) Monoblock ————————- Kirloskar make (ii) Energymeter ————————- Maxwell Jaipur make (iii) Water flow meter ————————- Kranti/Anand make.Services required :
(i) 440 v, 15 A, stabilized three phase A.C. supply. (ii) Floor area-2 mx2mxl.5m height (iii) Tachometer for speed measurement (can be supplied at extra cost)
Stop Cocks
We bring to you, polypropylene Stop Cocks.
The Stop Cocks offered by us are fitted with a PTFE plug & have serrated tubulations, that accept from 6 mm to 10 mm tubing.
The Stop Cocks are leakproof and are available in two different options i.e. 2 way & 3 way.
Material : Polypropylene/ PTFE
| Particulars | Pack (Pcs) | |
|---|---|---|
| Stop Cocks 2 Way | 6 | |
| Stop Cocks 3 Way | 6 |
Wheel And Axle, Simple Form
Wooden double wheeled pulley
Consisting of a wooden double wheel with flat-bottomed grooves, 150 and 50 mm diameter respectively.
The wheel is pivoted on a spindle 10 mm diameter which projects for a distance of 100 mm so that the apparatus may be clamped to a normal retort stand.
The apparatus is supplied complete with two hooks and 6 meters of cord but without masses and stand.
Synchromesh Gear Box 4 Forward 1reverse With Clutch Plate
Synchromesh Gear Box – 4 Forward & 1Reverse Actual Cut Section With Single Plate Clutch
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
Fuel Supply System Diesel CRDI Type
Fuel Supply System Diesel CRDI Type (Actual Working Model) Common Rail Direct Injection.
This is an actual working model of fuel supply system of a CRDI diesel engine. The parts details is as under ::
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under ::
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Power Supply
9. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of CRDI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
