XTEMOS ELEMENT
AJAX PRODUCTS TABS
PNEUMATIC TROUGH
PRODUCT DESCRIPTION:
Use a circular Glass Circular Pneumatic Trough made of soda lime glass to conduct gas analysis experimentation in the laboratory. A secondary use is for specimen storage
Features:
- Circular soda lime glass
- For collection of gases over water
- Three sizes
Digital Stroboscope
Description :-
Stroboscopic flashes are triggered by either the internal oscillator or by external pulses which may be connected to the two 4mm sockets mounted on the rear panel of the instrument. Example of the many applications of this unit are to be found in motion analysis multi exposures photography, examination of moving parts and measurement of rotational speed.
Specifications:-
Input Volts : 220V AC, 50 Hz
Flash Rate: 0- 9999 Flashes per minute.
Resolution : 1
Display: 7 Segment LED (4 nos.)
Solar Wind 3Φ, 2KW Smart Grid
This consists of 2 Microgrids of 2000W &1000W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. A 3Φ 3KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 3Φ, 2.5KVA Grid Commercial Solar Power Inverter can be added to this experimental setup. By adding 3Φ, 2.5KVA commercial solar inverter, when the experimental setup is not used by student, it may be used to generate power.
This Advanced Smart Grid Experimental Setup Consists of
• 2 Micro Grids, each 1000W of power generation using Solar, Wind or Hybrid • An Isolation Transformer Coupled to the utility Grid, acts as Main Grid to this Setup • Various other Power Sources • Commercial 3Φ 5KVA Grid Connected Inverter (Optional) • Optional Components for the Smart Grid Setup • DSP /FPGA Controller for PE, SG, PS Applications • Other Add ons • Components for Building 10/25KW Smart Grid Power Generation • IoT Based Data Acquisition.Solar Wind Grid Connected 3Φ, 2KW Smart Micro Grid
• Main Frame • 1KW Solar PV Module with Stand • Wind Turbine • DC-DC Boost Converter • 120V Battery Bank - 12V x 100AH x 10 Nos • 2KW Bi-Directional DC-DC Buck-Boost Converter for Charging battery • 2KW 3Φ Inverters • DSP/FPGA Controller • Microcontroller based Protection Relays • Smart Energy Meter • Synchronizing Panel • Three Phase RL Load 2KW • PLC with SCADA Software • 14 Channel PC based Power Quality Analyzer (Optional)
Human Eye In Bony Orbit
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Microtome
Decade Inductance Box – 7 Dial
Description
Housed in a box with seven dials and fitted with 4 mm output plugs, the unit allows a range of inductances from 1ΩH to 10ΩH. 7 Decade Inductance Box (i) 1ΩH to 10ΩH in steps of 1ΩH (ii) 10ΩH to 100ΩH in steps of 10ΩH (iii) 100ΩH to 1mH in steps of 100ΩH (iv) 1mH to 10mH in steps of 1mH (v) 10mH to 100mH in steps of 10mH (vi) 100mH to 1mH in steps of 100mH (vii) 1mH to 10mH in steps of 1mH
IoT Development System
The industrial networks are primarly concerned with Programmable Logic Controllers(PLC),Distributed Control Systems(DCS), Supervisory Control and Data Acquistion Systems(SCADA) any many other hetrogenous devices in the form of differnt applications. More over these devices are based on either wired or wireless communication protocols like Profinet, Profibus, MODbus, WiFi, Zigbee and Etc.
Specification:
• To impart the knowledge about Industrial IoTa the Students, We have designed a IIOT trainer kit, which have inter-quark chip based IoT Gateway. • This Gateway is a universal Gateway supports many different types of communication protocols such as wired and Wireless communication for industrial applications. • The IIoT Gateway connected with Siemens based Distributed Control System(DCS), Programmable Logic Controller(S7-1200, S7-1500) using S7-protocol and OPC UA. • The Intel centrino based powerful WiFi chip enables us to the access data via Mobile Application. • The Gateway can get the internet connectivity via Ethernet and WiFi also. • This Gateway can communicate with our own ingenious data acquisition system using RS485 BUS and RS232 Bus. • The USB based communication exchange the data between Zigbee co-coordinator and Gateway.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Amphibia
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall, Size 75×100 cm. Frog External character Frog Internal Anatomy Frog Skeleton Frog Skull, different views Frog Development part I-showing stages from egg to Gastrulation Frog Development part II-showing Gastrula to newly hatched Tadpole
francis turbine test setup
DESCRIPTION:
Francis Turbine is a reaction Turbine, which was developed by English born American Engineer Sir J.B. Francis. The water enters the turbine through the outer periphery of the runner in the radial direction and leaves the runner in axial direction and hence it is called a mixed flow turbine. As the water flows to the runner, a part of pressure energy goes on changing into kinetic energy. Thus the water through the runner is under pressure. The runner is completely enclosed in an air tight casing and the casing & runner is always full of water. The present Set-up consists of a runner. The water is fed to the turbine by Means of centrifugal Pump, radially to the runner. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is provided with a transparent. The circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the runner. The runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of brake arrangement so that the efficiency of the turbine can be calculated. A draught tube is fitted on the outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and vacuum Gauge are fitted at the Inlet and Outlet of the turbine to measure the total supply head on the turbine.UTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V Ac, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 101 (1.33 HP) | HM 101 (2 HP) | HM 101 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1 Kw | 5 HP / 3.75 Kw |
| Discharge | 1000 LPM (Approx.) | 1000 LPM (Approx.) | 2000 LPM (Approx.) |
| Supply Head | 10 m | 10 m | 15 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 300 Ltrs. | Capacity 300 Ltrs. | Capacity 600 Ltrs. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1500 RPM (approx.) | ||
| Runner | Having Curved Vanes | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
Three Phase Transmission Line Fault Analysis Trainer
Three phase Transmission line fault Simulation Study Module
Specification
• 3 phase power supply from 3 phase generator • To simulate 3 phase balanced system fault and unsymmetrical faults • Fault study with single line and double line in 3 phase system • Faults : - L-G-Fault - L-L-Fault - L-L-G-Fault - Single Conductor open fault - Double Conductor open fault - Fault through impedance • Theoretical calculations and verification with practical results. • The transmission lines are simulated by high frequency Inductance & resistance for short, medium and long line.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Capsule Counter (Aluminium) 100 places
Cyclone IV FPGA Controller
FEATURES:
• Based on Altera family Cyclone IV, Device : EP4CE30 • One 34 pin header used for IPM Interface. - 16 PWM output - 8 capture inputs. • One 26 pin header ADC. - 4 channel 1MSPS ADC. - Total 8 channel using 2 Nos of ADC. - 12 bit resolution. - Input range -10V to 10V / -5V to 5V. • One 5 pin phoenix connector DAC - 4 channel DAC, 12 bit resolution. - Output range -10V to 10V / -5V to 5V. • 8 output Light Emitting Diodes (LEDs). • 8 input slide Switches. • 4 user push button switches. • 2-user limit switch. • 20 x 4 Alphanumeric LCD display. • On Board Isolated JTAG Programmer Compatible with QuartusII software. • Isolated USB (USB to Serial) interface. • 3 Nos of 20 pin header each have 16 IOs.
Hypsometer, Regnault’s
Description
Double walled copper cylinder, 340 x 60 mm, mounted on steam boiler, with thermometer tubule at top and side outlets for manometer and draining. Double walled copper cylinder 34 x 6 cm mounted on steam boiler. Fitted with thermometer, draining tube and glass manometer with rubber bungs. For the determination of the upper fixed points of thermometers andboiling points at barometric pressures other than atmospheric. Double walled copper cylinder 34 x 6 cm height x outer dia. mounted on steam boiler. Fitted with thermometer tubulure at the top, side outlet draining tube and glass manometer mounted in tubulure with rubber bungs.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Polarising Filter Stress Determination
Description
Demonstrate stress patterns in solids with this new and valuable equipment. Two polarising filters, mounted on a graduated frame are placed on a plastic base. Clear acrylic pieces of different shapes are introduced between the filters; when pressure is applied to the solids the resulting stress patterns are observed. An important method of demonstrating polarisation and stress. Includes instructions.
Tuning Fork, Superior
Porifera , Coelenterata
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Phylum Porifera showing sponges of principal types Sycon Development structure & L.H. Obelia structure & Life History Hydra structure & Internal Anatomy Ascaris Internal structure of male & female Tapeworm structure & Life History Liver fluke structure & Life History Hook worm,structure & Life HistoryXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Micrometer Screw Gauge
Micrometer Screw Gauge
• Strong rugged metal construction.
• Economical, suitable for all uses, teaching, demonstration, labs, machine shops.
• Measuring screw handle, Satin finish with friction knurling for easy rotation.
• With locking mechanism to hold measurements.
• 25 x 1 mm, reads to 0.01 mm.
• Supplied with hex wrench for zero adjustment and plastic case for storage.
Planck’s Constant
Modern LEDs (light emitting diodes) cover the range from deep blue (440 nm) to infra-red (940 nm). By monitoring the voltage at which each LED just begins to emit light a graph of energy input as a function of light emitted frequency can be plotted and an approximate value of Planck’s constant deduced. Complete with viewing tube but without power supply.
Accessories For Plane Table
Description
We offer a wide range of very high quality Plane Table Accessories that are suitable for maps preparation and recording topography in various engineering surveys. This outfit consists of a plane table board with a fitted tripod. These products undergo various quality tests at each level of its production to ensure good quality and flawless performances. These products are basically used in the construction industry for the purpose for surveying the land for commercial use.Features :
• Export quality. • Reasonable price. • Customer centric organization. • Customizable.Specifications:
• Size: 54 X 34 X 22 + 8 CM. • Material: Green Bamboo, Natural and Environmental.
Bacteriological Incubator
Specification
Standard Double Wall Fabrication, inner & outer chamber made of thick mild steel sheet. Painted with hammer tone paint finish. The gap between the walls is fitted with special grade glass wool. Provided with two or three removable shelves. Heating elements provided on three sides to attain quick and uniform heating in range of 30°C to 110°C + 1°C controlled by hydraulic type capillary thermostat. An L- Shaped prismatic thermometer is fitted to the unit for reading the chamber temperature. Equipment suitable to be working on 220V AC 50Hz single phase.Optional
Air circulating fan. Timer 0-24 hours.| Chamber Size In mms | Chamber Size | Cap. (App.) |
|---|---|---|
| 300x300x300 | (12"x12"x12") | 28L |
| 350x350x350 | (14"x14"x14") | 45L |
| 400x400x400 | (16"x16"x16") | 65L |
| 450x450x450 | (18"x18"x18") | 95L |
| 600x450x450 | (24"x18"x18") | 125L |
| 600x600x600 | (24"x24"x24") | 224L |
4 Stroke 6 Cylinder Petrol Engine V-6
4 Stroke 6 Cylinder Petrol Engine (V-6) Motor Driven Actual Cut Section Working Model
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine willbe supplied with key card & very interesting literature regarding working.
LABORATORY JACK MILD STEEL
Product Description
Laboratory jack, an all purpose constructed from stainless steel, mild steel. Suitable for hot plates, burners, baths, glassware many more items. it is a knob operated scissor action lifting mechanism for quick, easy accurate height adjustment. Mild steel jacks are finished with powder coated. AVAILABLE SIZES:- Plate Size 8”x8”
- Plate Size 10”x10”
