XTEMOS ELEMENT
AJAX PRODUCTS TABS
Corner Cube Reflector
Description
To demonstrate principles of light and reflection, The reflector features three front-surfaced triangular mirrors mounted at right angles to one another on a hardwood base. Light beams hitting any of the mirrors from any angle are bounced off the other two mirrors and reflected back in the same direction they came from. With instructions.
Burner Bunsen-Heavy Base
Description
Comprises of heavier casted base giving the stability to the burner. Total weight of the burner is about 350 g. Nickel plated brass burner tube with rotatable air regulator & cylindrical riffled connector, mounted on casted base. Burner tube 12.5 mm dia. base 75 mm dia. connector 10 mm o.d. For use with LPG / Butane gas.
Synchromesh Gear Box 4 Forward 1reverse
Synchromesh Gear Box – 4 Forward & 1Reverse Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Fully Automatic Battery Charger
SILICA MOISTURE DISH With Lid – Translucent
Falling Body Apparatus
L-Section launcher with holes for locating two 19mm.
diameter steel balls which act as projectiles.
Launcher is released by push button and projects one ball forward while allowing the other to fall freely Launching mechanism mounted on wooden block, 180x60x30mm.
which may be clamped by bench and has a convenient storage pocket for the balls.
Complete with two steel balls.
Micrometer Screw Gauge
Micrometer Screw Gauge
• Strong rugged metal construction.
• Economical, suitable for all uses, teaching, demonstration, labs, machine shops.
• Measuring screw handle, Satin finish with friction knurling for easy rotation.
• With locking mechanism to hold measurements.
• 25 x 1 mm, reads to 0.01 mm.
• Supplied with hex wrench for zero adjustment and plastic case for storage.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Water Tap, Swan Neck, Light
Tubing, Rubber
Resistance Box, Plug Pattern
Description
All plugs are turned to a fine standard taper and are interchangeable. These are moulded in fluted plastic tops. The brass blocks are undercut and are fitted to a thick insulating plate. Heavy 4 mm brass terminals are used. Coils are non-inductively wound and are treated to be strain-free. Coil values are engraved on the plate and an infinity plug is also included. Accuracy ±0.5% for 0.01 to 0.05 ohm coils, ±1% for the rest 0.01 to 0.1 ohm, Total 0.2 ohm 0.1 to 1 ohm, Total 2 ohm 0.1 to 5 ohm, Total 11 ohm 0.1 to 10 ohm, Total 21 ohm 0.1 to 50 ohm, Total 111 ohm 0.1 to 100 ohm, Total 211 ohm 0.1 to 500 ohm, Total 1111 ohm 1 to 10 ohm, Total 20 ohm 1 to 50 ohm, Total 110 ohm 1 to 100 ohm, Total 210 ohm 1 to 500 ohm, Total 1110 ohm 1 to 1000 ohm, Total 2110 ohm 1 to 5000 ohm, Total 11110 ohmXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Neuron
Tangent Galvanometer
Episiotomy Training Simulator
Description
Suturing Simulators provide a realistic way for students to learn good surgical techniques. The simulators provide students with a variety of repair experiences without the constraint of time and concern for safety, which are factors with a live patient. The simulators can be used by the student in a learning lab with an instructor or by the student individually in the clinical setting just prior to a patient experience. They are also useful as homework teaching aids that can be signed out at night and returned the next day. In addition to being portable, the lifelike texture allows the learner to develop a “feel” for instrument handling, tension on suture, and the advantages of one method of tying knots over another.Includes one of each simulator:
Midline Suture Simulator Left Mediolateral Suture Simulator Right Mediolateral Suture Simulator Each simulator comes with an instruction booklet and is individually boxed.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Desert Cooler Trainer
Desert Cooler Trainer works on the principle of evaporative cooling. It is used mostly in the dry hot regions; it consists of a fan which sucks the air from atmosphere through the pads which are used in desert coolers very frequently. The difference in DBT & WBT at inlet and outlet can be measured hence the RH from the charts. Also the amount of water evaporated can be calculated by knowing the water level difference in the reservoir.
SPECIFICATIONS:
1.Fan connected to 1/2 HP motor. 2.Air Cooler Pump to circulate water. 3.DBT & WBT Measuring Thermometer at inlet and outlet. 4.Orifice meter with manometer to measure the air flow. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Floor Area – 1, X 1 m. X 1 -5m. Height. 2.220 V., 15 Amp. , Single Phase Stabilized power supply
Refrigerant Charging Unit
This charging unit is fitted with motorised vacuum pump and other safety devices like pressure gauge. With the help of this charging unit students can charge the refrigerant gases into compressor or store the gas of a refrigerator or air conditioner inside the cylinder fitted inside the charging unit that can be used later.
8086 Microprocessor Trainer Kit
Specification
• INTEL 8086CPU AT 4.77 MHZ CLOCK SPEED • 16KB for monitor EPROM upgradable to 64kb • 16KB RAM expandable to 64KB • Battery backup provision for RAM upto 64KB • 16 x 2 (or) 20 x 4 Alphanumeric LCD display • 101 keys IBM compatible keyboard • 24 TTL I/O lines brought out to two nos., of 26 pin FRC connector • 1 number of standard RS232C compatible serial port brought out to a pin D type male connector. • 3 channel 16 bit counter/timer using 8253. • Fully buffered address data and control signals terminated at a 50 pin header(VXT BUS) for interfacing VBMB series • of experiment boards and bus expansion. • 8 no’s of interrupt lines are terminated at a 10 pin connector. • Kit operates with a single +5V/DC supply • The kit and the power supply are mounted on a attractive light gray color fiber glass cabinet with fiber glass top cover. • Built-in line assembler & Disassembler • Powerful debugging monitor to develop user program.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Orfice Mouthpieces Apparatus
DESCRIPTION:
An orifice is an opening made in the side or bottom of tank, having a closed perimeter, through which the fluid may be discharged. A mouthpiece is short tube fitted to a same size circular opening provided in a tank so that fluid may be discharged through it. Orifice and mouthpiece are used to measure the rate of flow of liquid. The apparatus is designed to measure the co-efficient of discharge of orifice & mouthpiece. The apparatus consists of a supply tank, at the side of which a universal fixture for mounting orifice or mouthpiece is attached. A centrifugal pump supplied the water to supply tank. Head over the orifice/mouthpiece is controlled by a by pass valve provided at pump discharge. A measuring tank is provided to measure the discharge. A gauge for measuring X and Y co-ordinates of jet from the orifice is provided, which is used to calculate Cv of orifice.SPECIFICATIONS:
[1] Supply Tank – 0.4 X 0.3 X 0.5m height [2] Orifice – 8mm and 10 mm. [3] Mouthpiece (a) LID = 4 (b) L/D = 1 (c) Bordas mouthpiece. (d) Convergent mouthpiece. [4] X-Y gauge for orifice jet co-ordinates. [5] Measuring tank of suitable capacity OR a calibrated water flow meter. [6] Sump tank of suitable capacity. [7] 0.5 HP pump with valve. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC. Power Supply.
Smart LED Lighting module
Zigbee offers Green and Global Advanced Wireless Technology, Connecting the widest range of Devices to work together intelligently and help you to control your real world. CC2530 is the first System On chip, which has integrated 8051Microcontroller with ZigBee RF transceiver. A WSN based Smart LED lighting module has been developed with latest LED controller from MICREL, 10 LEDs, ZigBee RF module using CC2531 for Wireless Control with onboard Light Sensor. WSN based LED lighting module has a Base Board and a Zigbee RF module. Zigbee RF module can be plugged into the connector provided on the Base Board, meant for further upgradation.
Features
• 10 Nos. of LED of 2watt each • 400 milliwatts LED • Constant current driver for LED control • Connectors for plug-in Zigbee RF module • Remote ON/OFF control by Zigbee RF Control • On board light intensity sensor • LED Brightness control either by program or by Light Sensor input.
