XTEMOS ELEMENT
AJAX PRODUCTS TABS
Microcontroller Based Differential Relay
This test set-up consists of a. Microcontroller based differential relay. b. 300VA transformer set-up
Specification
• One PIC Microcontroller used as processor to read all current, (PY, SY) & activation of relay function • One LCD to indicate, - Set value, All currents - Set time, DMT/IDMT type - Relay tripping time. - Biased/Unbiased type status • Four numbers of key used - To select IDMT/DMT type or biased un-biased type - Set current value adjustment - Set time adjustment - Reset function • Six 5A CT used to sense primary and secondary current. • One 12V TPTT auxiliary relay used for contactor operation. • Specification: - Current input : 0-5Amp - Voltage input : 0-230V - Number of contact : Three number No contact @ 220V, 10Amp rating. - Auxiliary supply : 230VAC, 50Hz • PC interfacing facility power ON/OFF switch with indicator. • Make : VI MICRO • Model : VPL - 83A
Refrigeration Trainer Domestic Type
The unit enables students to study the various parameters affecting the performance of a domestic refrigerator. It consists of refrigeration cycle of domestic refrigerator, it consists a hermetically sealed compressor, air-cooled condenser, capillary tube and a natural convection type evaporator. The evaporator is fitted with a small heater to simulate different load conditions various measurements are provided so that power consumption, COP, theoretical and actual refrigerating effects refrigerant flow rate and effect of door opening on power consumption can be studied and also students can visualize automatic operation of unit using a thermostat.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirioskar make having capacity of approx. 1/25 ton of refrigeration. 2.Air – cooled condenser with natural convection airflow. 3.Capillary tube of matched length as expansion device. 4.Evaporator coil with an electric heater inside and adequate glass wool insulation on all side. 5.Measurement a)Energymeter Tore compressor input power measurement. b)Pressure gauge for condensing and evaporating pressure. c)Flow meter for liquid refrigerant flow d)Digital Temperature indicator for measurement of temperature 6.safety & Controls a)High & low pressure cutout. b)Thermostat. c)Necessary Switches. A technical manual accompanies the unit. Also, the unit is provided with an attractive and rust proof powder coating.SERVICES REQUIRED:
1.Floor space of 2m x 1m. 2.230V AC stabilized supply with earthing connection
Sieve Shaker (Hand Operated)
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Abney Level Made of Brass pipe
Thermistor Unit
Rotary Pipette Stand
Moulded in Polypropylene, the unique Rotary Pipette Stand holds a maximum of 94 pipettes and rotates on a central vertical axis for convenient selection of any particular pipette.
The lower rotating disc has four concentric troughs with tapered sides and open bottoms that cradle the pipette tips protectively and permit water drops to run off.
The upper disc has a grid pattern concentric with the bottom disc and keeps the pipettes vertical.
Liquids draining off the pipettes are retained on the top of the stationary base by the outer ring.
Our Rotary Pipette Stand can be easily disassembled and reassembled.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pipette Stand (Rotary) - For 94 pipettes | 1 | |
| Pipette Box | 4 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Force on a Conductor Balance
Description
To demonstrate that when a current is passed through a conductor in a magnetic field, it is subjected to attraction or repulsion depending upon the direction of current in it. The apparatus consists of a plastic base 160 x 140 mm on which two contact pillars are mounted. Each pillar is provided with an external circuit. A balanced beam is supported by the pillars on two bearings which form the fulcrum. Two screwed masses are provided in the beam system, one moving vertically for the adjustment of sensitivity and the other moving horizontally for the adjustment of the equilibrium position, when no current is flowing. Scale marked 0 to 75 x 1 mm, rider of 1 gm. weight with instruction manual.
Mock Layout Of Car Wiring Conventional Type
It is an open type instructional apparatus. This unit is capable of operation when a standard battery is connected to the given terminals, Consisting of all essential parts as self starter, alternator, ampere-meter, ignition coil, distributor, 4 spark plugs, horn, long lights with dipper light, park-lights, dipper, back stop light and switches. The whole system is beautifully fitted on 100 x 80 cm base with electric motor working on 220 volts A.C and capable to drive the alternator. Without battery.
Histology (Shark)
Cylinderical Magnet
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Pentax Tribrach Adaptor
Description
Traverse Tribrach Adapter with Optical Plummet • 2.5X optical plummet • 60-second plate vial, adjustable • Precision-machined axis rotates 360º • Compatible with all prisms with a 24.9 mm bayonet base • Adjustable height : 100 mm-to-120 mm • Fits all standard three-prong tribrachs • The over point accuracy is 0.5 mm at 1.5 m
Calorimeter copper
Demonstration Meter Inter Scale
Description
Housed in a ABS plastic case 300x150x300 mm with glass front and rear. Moving coil type with accuracy of + 2.5%. Basic sensitivity of meter is 5 mA, 100mV f.s.d. The meter can be used to demonstrate the working principle of AC or DC ammeters or voltmeters with the interchangeable plastic scales. DIFFERENT DIALS ARE AVAILABLE.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
PAM-PPM-PWM Modulation and Demodulation Trainer
PAM- PPM- PWM is the basic pulse modulation techniques. This trainer provides complete setup to the students for performing Experiments on these techniques. They can study Sampling, Pulse Modulation &Signal reconstruction process. Separate circuits are provided for each Techniques.
FEATURES:
• PAM- PPM- PWM Modulation and Demodulation Techniques,using Natural and Flat - top Sampling. • Natural Sample, Sample and Hold and Flat-top outputs. • Selectable 2 different sampling pulse frequencies on board. • On board Sine wave generators. • Voice communication using dynamic microphone and speaker • On board Filters and Amplifier • Functional blocks indicated on board schematic • Input- Output and Test points provided on board. • Built in DC Power Supply • Fully documented operating ManualTECHNICAL SPECIFICATION:
• Crystal Frequency : 6.14MHz • Sampling Frequency : 16 KHz, 32 KHz • Sine wave Generator : 1 KHz &500Hz, Amplitude (0-5)V, Tolerance +5% • Low Pass Filter : 4 Order BW Filter • Cut off frequency : 3.4 KHz • Voice Communication : Voice Link using dynamic mic& speaker • AC Amplifier : With Adjustable Gain control • Microphone type : Dynamic, 600 Ohm. • Audio Pre-amplifier : Op-amp based • Power amplifier : 1W Mono • Interconnections : BS2 Connector. • Power : 230V, 50Hz
P-N-P Transistor Unit
PIPETTE BULB
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Optical Bench, wooden
Description
A wooden base board with one meter scale divided into mm with following accessories: One each White face object and receiving screens each 150 x 100 mm with aperture mounted on wooden base with an index mark. Two plane mirrors 150 x 100 mm mounted as above. One lens holder V shaped, wooden. One needle vertically mounted in a short wooden rod on base. One candle holder on base. The components have the same optical center height.
Sliding Mesh Gear Box
Sliding Mesh Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
Laboratory Timer
This is a versatile timer quartz crystal controlled for very high accuracy.
which can be used for conducting experiments related to timing and motion with high accuracy.
Can be used for G by free fall liner air tracks, dynamic trolleys etc.
This timer has an in built power supply for the coil for G by free fall apparatus and lamps for photo gates.
Range : 0.001, 0.01, 0.1 Sec.
The above timer has a built in power source for photo gates and the coil for 'G' by free fall apparatus.
4 Stroke 4 Cylinder Diesel Engine
4 Stroke 4 Cylinder Diesel Engine – Motor Driven Actual Cut Section Working Model With Valve Timing Attachment
The engine be sectioned to show the internal constructional details.The working of individual part and accessories like Valves,Pistons,pumps,Crank and Camshaft,etc.will be demonstrated.It is provided with Flyweel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes.The actual cut section engine will be supplied with key card & very interesting literature regarding working.
Hydraulic Linear Actuation System Trainer with Labview Interfacing
Features
• This trainer helps to learn the characteristics of double acting cylinder namely direction, speed & force. • A Microcontroller ADC relay driver provided to actuate the cylinder. • Gear pump supplies the hydraulic fluid to double acting cylinder through direction control valve. • Pressure control valve controls the flow rate of fluid to cylinder. • Single phase induction motor drives the pump. • Control unit communicate with PC and controls the double acting cylinder using LabVIEWSoftwares. • Two proximity sensors are provided to indicate the position of the cylinder. • Load cell measures the force developed by the cylinder. • 5/2 Double Solenoid Valve directs the cylinder. • One tank is used to store the hydraulic fluid.
Elastically Coupled Beam Apparatus
Apparatus consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the centre of another elastic beam supported at two outer ends only. Mild steel Apparatus to be supplied should be complete with a supporting stand and a set of weights.
