XTEMOS ELEMENT
AJAX PRODUCTS TABS
Half lower Jaw
FLASK TONG
Amplitude Modulation And Demodulation
Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission. It is still used in radio system to transmit audio signal although it has lesser in popularity compared to FM (Frequency Modulation) due to its lower signal to noise ratio.
Technical Specification :-
1. I C based DC regulated Power Supply ±12 V / 500 mA.
2. Audio frequency 1 KHz / 0-2 Vpp for modulating signal 455 KHz / 2.5 Vpp approx. for Carrier Frequency.
6 Axis Robotic Trainer
For beginners this kit is very useful to learn the concept and working. For experienced, this kit helps to make new ideas. This kit is used to study the ROBO characteristics of arm movement. Each axis has one stepper motor. Gripper has one miniature cylinder to pick and place the object. Software controls the ROBO arm and measures the motor axis and arm axis. Simplicity of this kit makes maintenance easier and friendly to user. This kit is very flexible to operate and easy to move.
Features
• Easy to learn • New design • Easy for maintenance • Drive by stepper motor • Easy to programSpecification
• Arm : Jointed Arm • Axis : 6 • Motor : Stepper Motor • Gripper : Pneumatic • Drive : Stepper Motor Drive • Controller : MicrocontrollerBase
• Angle of movement : 320º • Gear Type : Spur Gear • Position Detector : Limit SwitchIntermediate ARM
• Angle of movement : 90º • Gear Type : Spur Gear, Worm Gear • Position Detector : Limit SwitchVertical ARM
• Angle of movement : 90º • Gear Type : Spur Gear • Position Detector : Limit SwitchXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Bernoulli S Theorem Apparatus
DESCRIPTION:-
The Set-up is designed to verify Bernoulli’s Theorem experimentally. Set up consists of a one piece clear acrylic test section with convergent and divergent part section, supply tank, measuring tank, inlet water tank and pump for closed loop water circulation. The test section is connected to Piezometer tubes through pressure tapping at different locations on the section to demonstrate the Bernoulli’s Theorem. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENTS:-
Ø To verify Bernoulli’s Theorem experimentally.FEATURES:-
Ø Clear test section Ø Closed loop water circulation Ø Compact & stand alone setup Ø Stainless Steel tanks and wetted parts Ø Superb Painted structure Ø Simple to operate & maintainUTILITIES REQUIRED: –
Ø Electricity Supply: Provide 230 +/- 10 VAC, 50 Hz, Single Phase electric supply with proper earthing (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump Ø Water Supply : Tap water connection ½ “ BSP, Distilled water @ 60 Ltrs. (Optional)TECHNICAL SPECIFICATION: –
Ø Test Section : Material Acrylic, Size Ø Inlet Tank : Capacity 20 Liters., Stainless Steel Ø Supply Tank : Capacity 70 Liters., Stainless Steel Ø Measuring Tank : Capacity 20 Ltrs. Fitted with Piezometer Tube & Scale Ø Piezometer Tubes : Material P.U. Tubes (9 Nos.) Ø Pump : FHP Capacity make Tullu/Crompton Graves Ø Piping : GI / PVC Size BSP Ø Stop Watch : Electronic Ø The whole Set-up is well designed and arranged in a good quality painted Structure.
Frequency Response Analysis of Lead Lag Network
Frequency response of Lead, Lag network using P+I+D controller is a special purpose analog simulation, create using operational amplifiers. This simulator permits a detailed analysis of the first order and second order systems on the application of proportional, integral and derivative control to the improvement of their performance. The simulator may be used at high frequency for oscilloscope observation.
FEATURES:
• Built-in Function Generator (sine & square). • Self contained power supplies and power ON/OFF switch with indication. • Full mimic diagrams in the front panel. • The simulated process. - Simple Lag Process - Simple Lead Process • The simulated PID controller - Integral controller scaled in Integration time. - Derivative controller scaled in derivative action time. - Proportional band control scaled in % proportional band (PB).
Rear Suspension System
In this model the working of rear suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a rear suspension system are shown in actual working form. This model helps the student to understand the working of the rear suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Leaf Spring Type Suspension System With Rear Rigid Axle
(B) Rear Independent Type Suspension System
Flower & Embryology
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Typical flower showing parts Fertilization showing germination of pollen T.S Anther & its development Germination of pollen grain and development of male Gametophyte Megasporogensis Development of embryo and endosperms Development of embryo in sagittaria Embryo in Capasella Microsporangium Types of emchryo sacs Forms of Androecium Form of Gynaecium Development of Monocot embryo Placentation Aestivation L.H. Datura Inflorescene Part – I showing simple racemose & simple cymose Inflorescene Part – II showing compound & special Pollination different types Forms of ovules Forms of Calx & corollaXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Photon Energy Array
Rock Cycle Model
Electrophoresis Horizontal
Description
With rich industry experience and support of highly skilled quality experts our organization is engaged in providing a wide range of Electrophoresis Horizontal Mini-GEL that is commonly used for carrying out number of analytical tests by separating DNA and RNA on the basis of shape, size, and electrical affinity. It is offered with platinum electrodes that are almost hundred percent pure. We also provide gel casting tray, one comb with a terminal lead.Features:
Easy maintenance Precision-designed Flawless functioning
Aves Histology
Educational Equipments Manufacturer, Exporters & Suppliers - School Educational Equipments Manufacturers & Exporters of Educational Equipments for Lab.
Science Lab Products, Teaching Aids, Classroom Instruments, Educational Laboratory
| Skin VS | Skin VS with Feather |
| Bird Filoplume Feather WM | Bird Down Feather WM |
| Epiglottis TS | Oesophagus TS |
| Proventriculus TS | Duodenum TS |
| Small Intestine TS | Large Intestine TS |
| Gizzard TS | Spleen TS |
| Spleen TS | Liver TS |
| Pancreas TS | Trachea TS Lung TS |
| Kidney TS | Ovary TS |
| Testis TS | Heart TS Ventricle |
| Heart TS Auricle | Heart LS |
| Artery TS | Vein TS |
| Bone TS | Spinal Cord TS |
| Nerve TS | Choaca TS |
| Eye Pectin | Brain TS through different Regions |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Roots, Stems, Leaves
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multicolours with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. T.S Dicot root T.S Monocot root T.S Dicot stem T.S Monocot stem T.S Dicot leaf T.S Monocot leaf Root modification Stem modification (Arial) Leaf modification T.S dicot stem secondary growth Vegetative propagation Artificial propagation Specialized stems Typical leaf showing parts Types of leaves Simple leaves Stipules Leaf venation Compound leaves Phyllotaxy T.S. Dicot root Leaf Lamina secondary growth
Funnel Holder
The Funnel Holder offered by us is made of Polypropylene.
The corrosion free Funnel Holders can hold funnels with diameter 3" to 6".
The extra plate provided can be placed to hold funnels bearing diameter 1" to 3".
Two tapered wedges are provided to ensure firm grip on Rods having diameter ½" or 3/8".
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Funnel Holder - Single | 12 | |
| Funnel Holder - Double | 6 | |
| Seperatory Funnel Holder | 12 |
6 Axis Robotic Trainer
For beginners this kit is very useful to learn the concept and working. For experienced, this kit helps to make new ideas. This kit is used to study the ROBO characteristics of arm movement. Each axis has one stepper motor. Gripper has one miniature cylinder to pick and place the object. Software controls the ROBO arm and measures the motor axis and arm axis. Simplicity of this kit makes maintenance easier and friendly to user. This kit is very flexible to operate and easy to move.
Features
• Easy to learn • New design • Easy for maintenance • Drive by stepper motor • Easy to programSpecification
• Arm : Jointed Arm • Axis : 6 • Motor : Stepper Motor • Gripper : Pneumatic • Drive : Stepper Motor Drive • Controller : MicrocontrollerBase
• Angle of movement : 320º • Gear Type : Spur Gear • Position Detector : Limit SwitchIntermediate ARM
• Angle of movement : 90º • Gear Type : Spur Gear, Worm Gear • Position Detector : Limit SwitchVertical ARM
• Angle of movement : 90º • Gear Type : Spur Gear • Position Detector : Limit SwitchXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
TMS320VC5416 Based DSP Trainer
This Kit provides new performance enhancing Features such as USB Communications. This is Suitable for applications that require optimized Combination of Power Performance & area. Suitable for the range of Signal processing applications, including speech Compression / decompression Speech recogniation, echo generation and Cancellation.
ON-CHIP FEATURES:
• 160MIPS Performance, can operate upto 160MHz • Advanced multi bus architecture with one program bus, three data buses and four address buses • 40-bit arithmetic logic unit (ALU), including a 40-bit barrel shifter and two independent 40-bit accumulators • 17-bit × 17-bit parallel multiplier coupled toa 40-bit dedicated adder for non pipelined single-cycle multiply/accumulate (MAC) operation. • Compare, select, store unit (CSSU) for the add/compare selection of the Viterbi operator • Exponent encoder to compute the exponent of a 40-bit accumulator value in a single cycle • Two address generators, including eight auxiliary registers and two auxiliary register arithmetic units.ON-BOARD FEATURES:
• 4 Mbit (256Kb x 16) Flash Memory • 4 Meg (256K x 16-Bit) Static RAM for External Program/Data • 8 way DIP switch & LED • ON Board JTAG Emulator (XDS 100 version - 2) • PCM3002 AUDIO CODEC • Expansion connector for GPIO & Peripheral interface • On board USB for serial communication
Cryo Bath
Cryo Bath are one of the very important equipments which are used in several laboratory utilities.
These cryo baths are generally used for the purpose of freezing down the tissue samples at drastically low temperatures in very quick span of time while keeping the samples intact, distortion free and free from microscopic ice crystals.
Features
Micro-controller based temperature controller for temperature control. The unit is mounted on castor wheels for ease of mobility. Circulating pump for uniform temperature. Cabinet construction with stainless steel interior tanks to withstand critical applications. Audio visual alarm for controlling temperature deviation from preset temperature. Display of set value & process value. Integrated industrial strength pump for internal circulation. Temperature uniformity throughout the liquid medium. Rounded corners for better water circulation, improved uniformity and easier cleaning. Foam in placed PUF insulation for improved temperature stability and energy efficiency. 316 stainless steel construction for resistance against chemicals and simplified cleaning. Long-life heating elements for quick response to controller. Attractive front panel bezel for easy cleaning. GMP model: Inner chamber is made of 0.8 mm thickness and outer is of S.S 304, 1.0 mm thickness. NB: Specifications are subject to change without prior notice.Below mentioned are other details of our range of Cryo Bath
| Operating Voltage | 230 V AC | |
| Heating Power | 1250 W. | |
| Protection Fuse | 10 amps. | |
| Temperature | 0 to 40 °C | |
| Accuracy | ± 0.2 °C |
Reciprocating Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Reciprocating Pump. The Set-up consists of a Reciprocating Pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop water circulation. Pressure and Vacuum Gauge are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
To determine overall efficiency and pump efficiency of the Reciprocating Pump To plot Head vs. Discharge, Pump efficiency vs. DischargeFEATURES:
Closed loop water circulation Compact & stand alone set-up MS Excel sample calculation program on demand Stainless Steel tanks and wetted parts Superb painted structure Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½” BSP., Distilled water @ 80 Ltrs. (Optional extra cost)TECHNICALS SPECIFICATIONS:
Pump : Double acting, single Cylinder, Capacity 1 HP Speed 250 RPM (max.), Head 5 Kg/cm2 (max.) Drive : AC Motor with step cone pulley arrangement for 3 prefixed speed Or DC Motor with DC Drive along with non-contact type Digital RPM Indicator Supply Tank : Capacity 70 Ltrs. Measuring Tank : Capacity 50 Ltrs. fitted with Piezometer Tube & Scale Piping : GI / PVC Stop Watch : Electronic Control Panel : With required electrical instrumentation The whole Set-up is well designed and arranged in a good quality painted structure.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Distributed Control System
A powerful, modular & upgradable DCS has been designed and configured based on Siemens controller SIMATIC PCS7 ASRTX (Micro Box). Distributed I/O system ET200M can be provided for field automation. The distributed I/O can be connected via Profibus, Communication. DCS consists of controller, Power supply unit, distributed I/O, Digital Input and Output modules, Analog Input and Output module. a Demo Panel and Simatic PCS7 V9.0 Software.
DCS Controller
• Make : SIEMENS. • Controller : SIMATIC PCS 7 AS RTX BOX. • Profibus Communication done via CP5611 onboard. • Transmission Rate of Profibus cable is 12 Mbit/s. • 2 x GBIT & RJ45 LAN • Core 17-3517 Processor 1.7GHz, 4GB DDR3 RAM, SSD 80GB, 4xUSB V3.0 • Mouse and Keyboard • Windows7 • Win AC RTX 2010 software controllerDistributed I/O station ET200M
• Support HART, PROFIBUS, Foundation Field bus. • 16 No’s of digital Inputs with 24V DC. • 16 No’s of digital Outputs with 24V DC. • 8 channels of Analog Inputs with 4-20mA. • 8 channels of Analog Outputs with 4-20mA. • 24VDC /10A inbuilt power supply.
SILICON RUBBER CORK
PRODUCT DESCRIPTION
A Bung, Stopper or Cork is a truncated cylindrical or conical closure to seal a container such as bottle, tube or barrel. Unlike a lid, which encloses a container from outside without displacing the inner volume, a bung is partially inserted inside the container to act as a seal. These can be used for all types of glass bottles. These stoppers fit tightly to prevent chemical leaks. We are one of the very few manufacturers of silicone rubber corks, septa gasket, silicone rubber stoppers in India.
Features:
- Silicon rubber cork / stopper /bung,
- Silicon rubber cork for filtration flask.
Window Air Conditioning Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
