XTEMOS ELEMENT
AJAX PRODUCTS TABS
TMS320VC5416 Based DSP Trainer
This Kit provides new performance enhancing Features such as USB Communications. This is Suitable for applications that require optimized Combination of Power Performance & area. Suitable for the range of Signal processing applications, including speech Compression / decompression Speech recogniation, echo generation and Cancellation.
ON-CHIP FEATURES:
• 160MIPS Performance, can operate upto 160MHz • Advanced multi bus architecture with one program bus, three data buses and four address buses • 40-bit arithmetic logic unit (ALU), including a 40-bit barrel shifter and two independent 40-bit accumulators • 17-bit × 17-bit parallel multiplier coupled toa 40-bit dedicated adder for non pipelined single-cycle multiply/accumulate (MAC) operation. • Compare, select, store unit (CSSU) for the add/compare selection of the Viterbi operator • Exponent encoder to compute the exponent of a 40-bit accumulator value in a single cycle • Two address generators, including eight auxiliary registers and two auxiliary register arithmetic units.ON-BOARD FEATURES:
• 4 Mbit (256Kb x 16) Flash Memory • 4 Meg (256K x 16-Bit) Static RAM for External Program/Data • 8 way DIP switch & LED • ON Board JTAG Emulator (XDS 100 version - 2) • PCM3002 AUDIO CODEC • Expansion connector for GPIO & Peripheral interface • On board USB for serial communicationPetri Dish
These Petri Dish offered by us is clear, unbreakable, & autoclavable.
The PS Petri Dish with fitting proves excellent for culture exp.
Made in polystyrene, this transparent Petri Dish provides an excellent inside view.
Material : Polypropylene
Particulars | Pack (Pcs) | |
---|---|---|
Petri Dish 50 mm | 36 | |
Petri Dish 75 mm | 36 | |
Petri Dish 100 mm | 36 | |
Petri Dish 125 mm | 12 | |
Petri Dish 150 mm | 12 | |
Petri Dish (Culture) | 12 |
Pilot Static Tube Set Up
DESCRIPTION:-
A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper / SS is supplied and is fixed below Vernier scale. The Vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow. A U-tube manometer is provided to determine the velocity head. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot tube Ø To plot velocity profile across the cross section of pipeUTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pitot Tube : Material Copper/SS of compatible size fitted with Vernier Scale Ø Test Section : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 40 Ltrs. Ø Sump Tank : Capacity 70 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted StructureXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE

Pole Holder
Description
We are supply of high quality Pole Holders for prisms. These have been manufactured using the finest quality of aluminium and brass, in order to ensure their strength and durability. We provide the poles in the shape of a tripod for increased sturdiness while holding prisms and other survey instruments. We also offer customization and can supply these products in accordance with the demands of our clients.The specifications of the Pole holder :
• Manufactured using fine quality aluminium and brass • High on parameters like strength and durability • Improved sturdiness while holding survey instrumentsCPR Training Manikins(torso)
Conical Friction Clutch Working Model
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
SENIOR RESEARCH BIOLOGICAL MICROSCOPE
BIIC-220 Series
Micron BMC-220 is the newly introduced series o[educational Microscope which extend top quality optics and uncompromising performance for educational and routine research work.
Features :
- Mechanical tube length 160 mm.
- 45 inclined with 360 degree rotatable binocular head.
- Co-axial built in Mechanical stage 140 x 140 mm with fine vernier graduation, designed with convenient coaxial adjustment forjerk free smooth slide manipulation through 55 x 75 mm.
- Dust proof quadruple/ quintuple ball bearing revolving nose piece with positive click stops.
- Co-axial coarse & fine focusing adjustment knobs on ball bearing guide ways. Fine motion, graduated to .002 mm.
- Staple Grey, chemical resistant, back-on finish.
- Adjustable focus lock prevents damage to valuable slide and objectives.
Lubrication System Of An Automobile
In this model the working of lubrication system of a car is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a lubrication system of a car are shown in actual working form. This model helps the student to understand the working of the lubrication system of a car very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION

Water Still with Metal Heater
Specifications
Water stills are carefully designed to produce high purity pyrogen free distilled water. The water still made from 3.3 exp. borosilicate glass comprises of horizontal type boiler, condenser, constant level device, silica sheathed heater, along with stand and clamps.Features
Borosilicate condenser and boiler are with a removable silica sheathed heater and screw threaded connectors for ease of Cleaning. Distillate temperature is approx. between 25° to 45°C which is ensured by an efficient condenser. The stand is powder coated for rust free operation and lustrous appearance. The unit automatically switches off if water level in the boiler falls below heater. Cooling water from the condenser is re-circulated into the boiling chamber, hence saving energy. Drain nozzle/Teflon Stop Cork is provided for easy cleaning and maintenance. Electrical Power: 220/240 V, 50/60Hz, Single Phase Supply.Plaque Building Anatomical Models
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Dissecting Trays
Model of Compound Microscope (BI STU)
Blood Bank Rrefrigerator
Features
Temp Range/Precision : 4 ±1°C, 0.1 °C Control System : Microprocessor control Display Alarm : Large screen LED display/ Audio and visual alarm for Height or low temperature; System failure; Door ajar; Power failure Refrigeration Type : Forced air refrigeration system Door : Three-ply transparent glass door with lock, Heating film preventing frosting, Stealing joint strip with magnetic force Casters : 4 casters Power Supply : 110/220V±10%, 50/60Hz Capacity : 120L Refrigerant : R134a, CFC-Free Material Internal : Stainless steel Material External : Cold-rolled steel with anti-bacteria powder coating Drawers/Shelves : Shelves Consumption : 160W External Size(L*W*H) : 520*600*1050mm Standard Accessory : Temperature printer, 2 shelves, 6 baskets, fluorescent lightSpecifications
Temperature- 2°C to 4°C Temperature Accuracy- + / - 1°C Temperature Controller- Digital P.I.D Controller Display- LCD / LED Display Alarm- Audio visual alarm for high and low temperature. Power Failure Alarm- Yes Refrigerant- Non-CFC Refrigerant Defrost type- Automatic Air Circulation- Forced air circulation External Construction- Stainless Steel 304 grades / MS Power Coated Interior Construction -Stainless steel 304 Insulation- CFC free high density polyurethane foam insulation Shelves- Adjustable and made of quality steel wire Illumination- Fluorescent Lamp Safety Device- High and low temperature protection Power Supply - 220 VoltsMulti Functional I.V. Training Arm
Description
The I.V. Injection Arm P50/1 made of silicone, is unique in quality and design and allows realistic training to teach competence to medical staff. It is also very suitable for group instruction because of its high quality, stain resistance and easy-to-clean soft material.It is ideal for practicing the following:
Correct puncture of peripheral veins for blood sampling. The following veins can be punctured: basilica vein, cephalic vein, median cubital vein, dorsal venous rete of hand Intravenous injections Positioning of a butterfly catheterDelivered in deluxe storage carton with:
1 injection arm with already mounted tubing system 1 infusion bottle 1 stand 1 bottle of artificial blood concentrate(250ml) 1 plastic cup 1 disposable syringe and 2 injection cannulas (recommended cannula size: 20 and 21 gauge) 2 tubing systems as replacement parts 1 container of talcum powderXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT